Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2013.08–2017.10
RM30M0E _58 Vehicle Interior _017113 METER / GAUGE / DISPLAY _0087658 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit is the power source circuit for the combination meter assembly. This circuit provides two types of power sources; one is a constant power source, and the other is an IG power source.

WIRING DIAGRAM

E254195E15
0.573,1.531 2.385,2.063 1.813,0.531 10 false from No. 2 Ignition Relay*1 or Ignition or Starter Switch Assembly*2 1.615,0.708 2.521,0.979 0.906,0.271 10 false from Battery 3.969,1.698 4.583,2 0.615,0.302 10 false METER 3.896,0.875 4.906,1.177 1.01,0.302 10 false SECURITY 5.25,1.427 5.583,1.615 0.333,0.188 10 false 39 5.26,0.594 5.604,0.802 0.344,0.208 10 false 40 5.26,2.219 5.583,2.417 0.323,0.198 10 false 21 5.521,1.531 5.844,1.719 0.323,0.188 10 false IG+ 5.51,0.719 5.74,0.896 0.229,0.177 10 false B 5.521,2.313 5.75,2.49 0.229,0.177 10 false ED 4.958,2.854 5.594,3.104 0.635,0.25 10 false F38 4.958,3.01 6.917,3.292 1.958,0.281 10 false Combination Meter Assembly 0.25,3 2.698,3.25 2.448,0.25 10 false *1: w/ Smart Entry and Start System 0.25,3.333 2.698,3.552 2.448,0.219 10 false *2: w/o Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY CIRCUIT)
a.
E219772C04
1.469,0.125 1.958,0.417 0.49,0.292 2.917,1.24 3.083,1.667 true 0.5,1.24 0.333,1.667 true 2.781,1.229 2.615,1.667 true 1.583,0.198 1.865,0.354 0.281,0.156 10 false F38 3.083,1.677 3.25,1.833 0.167,0.156 10 false B 2.5,1.677 2.792,1.833 0.292,0.156 10 false IG+ 0.198,0.094 0.406,0.25 0.208,0.156 10 false *a 0.25,1.677 0.542,1.833 0.292,0.156 10 false ED
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-21 (ED) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F38-39 (IG+) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
F38-40 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR