55900A
1.INSPECT HEATER CONTROL AND ACCESSORY ASSEMBLY (for LHD)
Check the resistance.
| *a | Component without harness connected
(Heater Control and Accessory Assembly) |
| *b | Blower Switch OFF Position |
| *c | Blower Switch LO Position |
| *d | Blower Switch M1 Position |
| *e | Blower Switch M2 Position |
| *f | Blower Switch HI Position |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 3 (LO), 5 (HI), 1 (M1), 6 (M2) - 10 (E) | Blower switch: OFF | 10 kΩ or higher |
| 3 (LO) - 10 (E) | Blower switch: LO | Below 1 Ω |
| 3 (LO), 1 (M1) - 10 (E) | Blower switch: LO - M1 | Below 1 Ω |
| 3 (LO), 1 (M1) - 10 (E) | Blower switch: M1 | Below 1 Ω |
| 3 (LO), 1 (M1), 6 (M2) - 10 (E) | Blower switch: M1 - M2 | Below 1 Ω |
| 3 (LO), 6 (M2) - 10 (E) | Blower switch: M2 | Below 1 Ω |
| 3 (LO), 6 (M2), 5 (HI) - 10 (E) | Blower switch: M2 - HI | Below 1 Ω |
| 3 (LO), 5 (HI) - 10 (E) | Blower switch: HI | Below 1 Ω |
If the result is not as specified, replace the heater control and accessory assembly.
Check that the illumination lights.
| *a | Component without harness connected
(Heater Control and Accessory Assembly) |
Apply battery voltage to the heater control and accessory assembly and check that the heater control and accessory assembly illuminates.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) →B-3 (ILL+)
Battery negative (-) → A-10 (E) |
Illuminates |
If the result is not as specified, replace the heater control and accessory assembly.
Check the A/C switch.
Measure the resistance according to the value(s) in the table below.
| *1 | A/C switch | - | - |
| *a | Component without harness connected
(Heater Control and Accessory Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-3 (LO) - B-4 (B) | A/C switch ON | Below 1 Ω |
| A-3 (LO) - B-4 (B) | A/C switch OFF | 10 kΩ or higher |
If the result is not as specified, replace the heater control and accessory assembly.
Check that the A/C switch indicator.
Connect the positive (+) lead from the battery to terminal A-9 (AC) and negative (-) lead to terminal B-4 (B).
Indicator lights up
If the result is not as specified, replace the heater control and accessory assembly.
55900A
2.INSPECT HEATER CONTROL AND ACCESSORY ASSEMBLY (for RHD)
Check the blower resistance.
| *a | Component without harness connected
(Heater Control and Accessory Assembly) |
| *b | Blower Switch OFF Position |
| *c | Blower Switch LO Position |
| *d | Blower Switch M1 Position |
| *e | Blower Switch M2 Position |
| *f | Blower Switch HI Position |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 (LO), 5 (HI), 1 (M1), 10 (M2) - 6 (E) | Blower switch: OFF | 10 kΩ or higher |
| 3 (LO) - 6 (E) | Blower switch: LO | Below 1 Ω |
| 3 (LO), 1 (M1) - 6 (E) | Blower switch: LO- M1 | Below 1 Ω |
| 3 (LO), 1 (M1) - 6 (E) | Blower switch: M1 | Below 1 Ω |
| 3 (LO), 1 (M1), 10 (M2) - 6 (E) | Blower switch: M1- M2 | Below 1 Ω |
| 3 (LO), 10 (M2) - 6 (E) | Blower switch: M2 | Below 1 Ω |
| 3 (LO), 10 (M2), 5 (HI) - 6 (E) | Blower switch: M2- HI | Below 1 Ω |
| 3 (LO), 5 (HI) - 6 (E) | Blower switch: HI | Below 1 Ω |
If the result is not as specified, replace the heater control and accessory assembly.
Check that the illumination lights.
| *a | Component without harness connected
(Heater Control and Accessory Assembly) |
Apply battery voltage to the heater control sub-assembly and check that the heater control sub-assembly illuminates.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → B-4 (ILL+)
Battery negative (-) → A-6 (E) |
Illuminates |
If the result is not as specified, replace the heater control and accessory assembly.
Check the A/C switch.
Measure the resistance according to the value(s) in the table below.
| *1 | A/C switch | - | - |
| *a | Component without harness connected
(Heater Control and Accessory Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-3 (LO) - B-3 (B) | A/C switch ON | Below 1 Ω |
| A-3 (LO) - B-3 (B) | A/C switch OFF | 10 kΩ or higher |
Check that the A/C switch indicator.
Connect the positive (+) lead from the battery to terminal A-7 (AC) and negative (-) lead to terminal B-3 (B).
Indicator lights up
If the result is not as specified, replace the heater control and accessory assembly.