Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM30M0E _59 Vehicle Exterior _017125 WIPER / WASHER _0090076 FRONT WIPER MOTOR G

WIPER / WASHER  FRONT WIPER MOTOR  INSPECTION  


CAUTION / NOTICE / HINT

CAUTION:

Ensure that fingers or articles of clothing do not get caught in moving parts when performing this test.


PROCEDURE

Hide 85110 1.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for LHD)

B343529
1.052,0.563 1.417,0.865 true 2.219,1.667 1.917,1.302 true 1.333,1.667 1.563,1.323 true 0.021,0.01 0.333,0.167 0.313,0.156 10 false *a 1.229,1.698 1.542,1.854 0.313,0.156 10 false +1 2.219,1.688 2.531,1.854 0.313,0.167 10 false E 0.854,0.469 1.167,0.708 0.313,0.24 10 false +2
*a Component without harness connected
(Windshield Wiper Motor Assembly)


a.

Check low speed operation.

i.

Connect the battery positive (+) lead to terminal 5 (+1) and negative (-) lead to terminal 4 (E), and check that the motor operates at low speed.

OK:

Motor operates at low speed.


If the result is not as specified, replace the windshield wiper motor assembly.



b.

Check high speed operation.

i.

Connect the battery positive (+) lead to terminal 3 (+2) and negative (-) lead to terminal 4 (E), and check that the motor operates at high speed.

OK:

Motor operates at high speed.


If the result is not as specified, replace the windshield wiper motor assembly.



c.
B343529
2.042,0.854 2.417,0.583 true 1.625,0.885 1.156,0.625 true 1.333,1.698 1.563,1.323 true 2.188,1.698 1.896,1.313 true 0.021,0.01 0.333,0.167 0.313,0.156 10 false *a 1.24,1.729 1.552,1.885 0.313,0.156 10 false +1 2.479,0.49 2.792,0.729 0.313,0.24 10 false +S 2.167,1.719 2.479,1.885 0.313,0.167 10 false E 1.042,0.49 1.354,0.729 0.313,0.24 10 false B
*a Component without harness connected
(Windshield Wiper Motor Assembly)


Check automatic stop operation.

i.

Connect the battery positive (+) lead to terminal 5 (+1) and negative (-) lead to terminal 4 (E). With the motor rotating at low speed (LO), disconnect terminal 5 (+1) to stop the motor operation at any position other than the automatic stop position.


ii.

Connect terminals 1 (+S) and 5 (+1). Then connect the battery positive (+) lead to terminal 2 (B) and negative (-) lead to terminal 4 (E) to restart the motor operation at low speed (LO).


iii.
B347425
0.302,1.552 0.781,1.979 true 0.115,1.5 0.427,1.656 0.313,0.156 10 false *a 0.833,1.906 1.146,2.063 0.313,0.156 10 false 30° 1.052,1.823 1.406,1.979 0.354,0.156 10 false +5° 1.052,1.979 1.396,2.135 0.344,0.156 10 false -10°
*a Automatic Stop Position


Check that the motor stops automatically at the automatic stop position.

OK:

Refer to the illustration


If the result is not as specified, replace the windshield wiper motor assembly.



Hide 85110 2.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY (for RHD)

B343529
2.042,0.854 2.417,0.583 true 2.24,1.646 1.917,1.302 true 1.333,1.667 1.563,1.323 true 0.021,0.01 0.333,0.167 0.313,0.156 10 false *a 2.458,0.479 2.771,0.635 0.313,0.156 10 false +1 1.229,1.688 1.542,1.854 0.313,0.167 10 false E 2.188,1.667 2.5,1.906 0.313,0.24 10 false +2
*a Component without harness connected
(Windshield Wiper Motor Assembly)


a.

Check low speed operation.

i.

Connect a battery positive (+) lead to terminal 1 (+1) and negative (-) lead to terminal 5 (E), and check that the motor operates at low speed.

OK:

Motor operates at low speed.


If the result is not as specified, replace the windshield wiper motor assembly.



b.

Check high speed operation.

i.

Connect a battery positive (+) lead to terminal 4 (+2) and negative (-) lead to terminal 5 (E), and check that the motor operates at high speed.

OK:

Motor operates at high speed.


If the result is not as specified, replace the windshield wiper motor assembly.



c.
B343529
2.042,0.854 2.417,0.583 true 1.625,0.885 1.094,0.406 true 1.333,1.667 1.563,1.323 true 1.396,0.99 0.729,0.573 true 0.021,0.01 0.333,0.167 0.313,0.156 10 false *a 2.458,0.479 2.771,0.635 0.313,0.156 10 false +1 0.531,0.458 0.844,0.698 0.313,0.24 10 false +S 1.229,1.688 1.542,1.854 0.313,0.167 10 false E 0.938,0.292 1.25,0.531 0.313,0.24 10 false B
*a Component without harness connected
(Windshield Wiper Motor Assembly)


Check automatic stop operation.

i.

Connect the battery positive (+) lead to terminal 1 (+1) and negative (-) lead to terminal 5 (E). With the motor rotating at low speed (LO), disconnect terminal 1 (+1) to stop the motor operation at any position other than the automatic stop position.


ii.

Connect terminals 3 (+S) and 1 (+1). Then connect the battery positive (+) lead to terminal 2 (B) and negative (-) lead to terminal 5 (E) to restart the motor operation at low speed (LO).


iii.
B343528
2.49,1.969 3.042,1.583 true 3.104,1.51 3.417,1.667 0.313,0.156 10 false *a 1.979,1.917 2.323,2.104 0.344,0.188 10 false 30° 2.24,1.833 2.583,2.021 0.344,0.188 10 false +5° 2.219,1.99 2.563,2.177 0.344,0.188 10 false -10°
*a Automatic Stop Position


Check that the motor stops automatically at the automatic stop position.

OK:

Refer to the illustration


If the result is not as specified, replace the windshield wiper motor assembly.