Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › 2013.08–2016.04
RM30M0E _53 Suspension _017095 FRONT SUSPENSION _0090096 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48520 1.INSTALL FRONT SHOCK ABSORBER ASSEMBLY

a.

Secure SST in a vise.

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)


b.
C294136E01
2.458,1.708 2.875,1.292 false 2.927,1.198 3.271,1.396 0.344,0.198 10 false SST

Temporarily install the front coil spring to SST.


c.
C275706C10
0.208,0.208 0.521,0.365 0.313,0.156 10 false *a 0.281,2.771 0.594,2.927 0.313,0.156 10 false *b
*a Correct
*b Incorrect


Attach the arm of SST to the diameter of the front coil spring.

CAUTION:
·

Make sure that the front coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.

·

Make sure that the claws of the hooks are securely attached.




d.

Using SST, compress the front coil spring.

CAUTION:
·

If the front coil spring bends during the compression, immediately stop the compression and reinstall SST.

·

Do not compress the spring until the coil springs contact each other.

·

Do not use an impact wrench. It will damage SST.




e.
C291496C01
0.656,0.865 1.542,0.406 true 1.615,0.302 1.927,0.458 0.313,0.156 10 false *a
*a Lower End


Install the front shock absorber assembly to the front coil spring.

NOTICE:
·

Install the front coil spring so that the end with the smaller diameter is facing upward.

·

Fit the lower end of the front coil spring into the gap of the absorber lower seat.




f.

Install the front spring bumper to the front shock absorber assembly.


g.

Install the front upper coil spring seat to the front shock absorber assembly.


h.
C294134C01
2.448,0.396 2.76,0.552 0.313,0.156 10 false *a 2.469,1.021 2.781,1.177 0.313,0.156 10 false *b
*a Upper Side
*b Lower Side


Install the strut mounting bearing to the front shock absorber assembly.


i.

Install the front suspension support sub-assembly to the front shock absorber assembly.


j.
C291497C01
0.594,0.656 0.99,1.031 false 2.271,2.406 2.583,2.563 0.313,0.156 10 false *a 0.094,2 0.406,2.156 0.313,0.156 10 false *b 0.292,0.552 0.656,0.729 0.365,0.177 10 false SST
*a Turn
*b Hold


Using SST and a 6 mm hexagon socket wrench, install a new front support to front shock absorber nut to the front shock absorber assembly.

SST
09729-97202  

Torque:
without SST : 55 N*m (561 kgf*cm, 41 ft.*lbf)
with SST : 48.5 N*m (495 kgf*cm, 36 ft.*lbf)

HINT:
·

This torque value is effective when SST is parallel to the torque wrench.

·

This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and SST with a fulcrum length of 40 mm (1.57 in.).

·

If using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




k.

Remove the front shock absorber with coil spring from SST.

NOTICE:

Do not use an impact wrench. It will damage SST.



Hide 2.TEMPORARILY INSTALL FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C287609

Temporarily install the front shock absorber with coil spring (upper side) and front No. 2 suspension support to the vehicle with a new nut.


b.

Install the front shock absorber with coil spring (lower side) to the steering knuckle with the 2 nuts and 2 bolts.

Torque:
164 N*m (1672 kgf*cm, 121 ft.*lbf)

HINT:

Keep the bolt from rotating while turning the nut.



Hide 47313J 3.INSTALL FRONT FLEXIBLE HOSE (w/ ABS)

Hide 47313J 4.INSTALL FRONT FLEXIBLE HOSE (w/o ABS)

Hide 5.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 6.TIGHTEN FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C284989C02
0.771,0.885 1.354,0.854 true 0.448,0.781 0.792,0.969 0.344,0.188 10 true SST 3.01,1 3.219,1.146 0.208,0.146 10 true *a 0.469,0.115 0.708,0.271 0.24,0.156 10 true *b
*a Turn
*b Hold


Using SST and a 6 mm hexagon socket wrench, hold the shock absorber rod in place and tighten the nut.

SST
09729-97202  

Torque:
without SST : 55 N*m (561 kgf*cm, 41 ft.*lbf)
with SST : 48.5 N*m (495 kgf*cm, 36 ft.*lbf)

HINT:
·

This torque value is effective when SST is parallel to a torque wrench.

·

This torque value can be obtained by using a torque wrench with a fulcrum length of 300 mm (11.8 in.) and SST with a fulcrum length of 40 mm (1.57 in.).

·

If using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




Hide 7.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 8.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT