Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM(for LH Side) › 2013.08–2017.10
RM30M0E _53 Suspension _017095 FRONT SUSPENSION _0090097 FRONT LOWER SUSPENSION ARM(for LH Side) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for LH Side)  REMOVAL  


PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 51451A 2.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 51405A 3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 48819A 4.REMOVE FRONT STABILIZER BOLT

a.
C287059C01
0.542,0.385 0.854,0.542 0.313,0.156 10 false *a 1.01,1.76 1.323,1.917 0.313,0.156 10 false *b
*a Turn
*b Hold


While holding the front stabilizer bolt with a wrench, remove the 2 nuts.


b.

Remove the 4 front stabilizer cushion retainers, front No. 2 stabilizer cushion retainer, 4 front stabilizer cushions and front stabilizer bolt.


Hide 48069 5.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C282354

Remove the clip and castle nut.


b.
C282353C01
2.385,1.354 2.573,1.094 false 2.615,1.01 3.073,1.208 0.458,0.198 10 false SST

Install SST to the threaded section of the lower ball joint.

SST
09960-20010  (09961-02060)

NOTICE:

Make sure the upper ends of the threaded section of the lower ball joint and SST are aligned.



c.

Using SST, separate the front lower No. 1 suspension arm sub-assembly LH from the front axle assembly.

C282355C01
1.031,0.531 0.906,0.229 true 1,2.073 0.719,2.365 true 3.677,2.302 3.375,2.427 true 0.552,2.281 0.865,2.438 0.313,0.156 10 false *a 1.792,1.646 1.948,1.802 0.156,0.156 10 false A 0.74,0.104 1.052,0.26 0.313,0.156 10 true *b 6.635,0.313 6.948,0.469 0.313,0.156 10 false *c 6.521,2.26 6.833,2.417 0.313,0.156 10 false *d 4.583,2.354 4.896,2.51 0.313,0.156 10 false *e 1.792,1.875 1.948,2.031 0.156,0.156 10 false B 6.625,0.615 6.938,0.771 0.313,0.156 10 false *c 3.052,2.375 3.375,2.531 0.323,0.156 10 false SST
*a Center Nut *b String
*c Molybdenum Grease Application Area *d Place the wrench here
*e Turn - -


SST
09960-20010  (09961-02010)

NOTICE:
·

Apply molybdenum grease to the bolt threads and the tip of SST.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

·

Install SST so that A and B are parallel.

·

Be sure to place the wrench on the part indicated in the illustration.

·

Do not damage the lower ball joint dust cover.

·

Do not damage the drive shaft outboard joint boots.

·

Do not damage the front disc brake dust cover.




d.
C285055

Remove the 2 bolts and front lower No. 1 suspension arm sub-assembly LH.