DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / EMPS / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Torque Sensor 1 Output | Torque sensor 1 output value | Min.: 0.0000 V
Max.: 4.9725 V |
2.3 to 2.7 V: The engine is running and steering wheel is not being turned (without load).
1.2 to 2.5 V: The engine is running and steering wheel is being turned to the left with vehicle stopped. 2.5 to 3.8 V: The engine is running and steering wheel is being turned to the right with vehicle stopped. |
- |
| Torque Sensor 2 Output | Torque sensor 2 output value | Min.: 0.0000 V
Max.: 4.9725 V |
2.3 to 2.7 V: The engine is running and steering wheel is not being turned (without load).
1.2 to 2.5 V: The engine is running and steering wheel is being turned to the right with vehicle stopped. 2.5 to 3.8 V: The engine is running and steering wheel is being turned to the left with vehicle stopped. |
- |
| Meter Vehicle Velocity | Vehicle speed from meter | Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph) |
·
0 km/h (0 mph) ·
No significant fluctuation. |
·
The vehicle is stopped. ·
The vehicle is driven at a constant speed. |
| Engine Revolution | Engine speed | Min.: 0 rpm
Max.: 8160 rpm |
No significant fluctuation. | The engine is running at a constant speed. |
| Motor Actual Current | Current to motor | Min.: -128 A
Max.: 127 A |
Value changes in proportion to steering effort. | The engine is running and the steering wheel is being turned. |
| Command Value Current | Amount of current requested for motor | Min.: -128 A
Max.: 127 A |
Value changes in proportion to steering effort. | The engine is running and the steering wheel is being turned. |
| Thermistor Temperature | ECU substrate temperature | Min.: -50°C (-58°F)
Max.: 205°C (401°F) |
- | The ignition switch to ON. |
| PIG Power Supply | Power source voltage to activate motor | Min.: 0.0 V
Max.: 25.5 V |
11 to 14 V | The engine is running and the power steering is operating. |
| IG Power Supply | ECU power source voltage | Min.: 0.0 V
Max.: 25.5 V |
11 to 14 V | The ignition switch to ON. |
| TRQ1 Zero Point Value | Zero point value of torque sensor 1 | Min.: 0.0000 V
Max.: 4.9725 V |
2.3 to 2.7 V | The engine is running and the steering wheel is not being turned. |
| TRQ2 Zero Point Value | Zero point value of torque sensor 2 | Min.: 0.0000 V
Max.: 4.9725 V |
2.3 to 2.7 V | The engine is running and the steering wheel is not being turned. |
| Motor Terminal Volt(+) | Motor terminal M1 voltage | Min.: 0.0 V
Max.: 25.5 V |
11 to 14 V: The engine is running and the steering wheel is being turned to the right.
6 to 11 V: The engine is running and the steering wheel is being turned to the left. |
- |
| Motor Terminal Volt(-) | Motor terminal M2 voltage | Min.: 0.0 V
Max.: 25.5 V |
6 to 11 V: The engine is running and the steering wheel is being turned to the right.
11 to 14 V: The engine is running and the steering wheel is being turned to the left. |
- |
| Steering Wheel Torque | Steering wheel torque | Min.: -7.00 Nm
Max.: 7.00 Nm |
Value changes in proportion to steering effort. | The engine is running and the steering wheel is being turned. |
| Motor Overheat Record | Continuous overheat prevention control record | Unrec or Rec | Unrec | - |
| Motor Lo Power Record | PIG power source voltage drop record | Unrec or Rec | Unrec | - |
| Battery Voltage Lo Record | Battery voltage reduction history | Min.: 0 times
Max.: 255 times |
0 to 255 times | - |
| Control Mode | Codes indicating DTC detection timing during ECU control displayed in hexadecimal | - | - | - |
| IG ON/OFF Times | Number of times ignition switch turned to ON/off after failure detected | Min.: 0 times
Max.: 255 times |
- | This value indicates the number of times the ignition switch has been turned to ON and off after the latest DTC storage. |
| The Number of DTCs | Number of stored DTCs when freeze frame data stored | Min.: 0
Max.: 255 |
0 | - |
| ECU Identification | ECU Identification | 01-09, 11 or 12 | - | - |
| Test Mode Status | Test mode status | Normal or Test | Normal mode: Normal
Test mode: Test |
- |