FREEZE FRAME DATA
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / EMPS / Trouble Codes.
According to the display on the GTS, select the freeze frame data.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Torque Sensor 1 Output | Torque sensor voltage | Min.: 0.0000 V
Max.: 4.9725 V |
2.3 to 2.7 V: The engine is running and steering wheel is not being turned (without load).
1.2 to 2.5 V: The engine is running and steering wheel is being turned to the left with vehicle stopped. 2.5 to 3.8 V: The engine is running and steering wheel is being turned to the right with vehicle stopped. |
- |
| Torque Sensor 2 Output | Torque sensor voltage | Min.: 0.0000 V
Max.: 4.9725 V |
2.3 to 2.7 V: The engine is running and steering wheel is not being turned (without load).
1.2 to 2.5 V: The engine is running and steering wheel is being turned to the right with vehicle stopped. 2.5 to 3.8 V: The engine is running and steering wheel is being turned to the left with vehicle stopped. |
- |
| Meter Vehicle Velocity | Vehicle speed from meter | Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph) |
·
0 km/h (0 mph) ·
No significant fluctuation. |
·
The vehicle is stopped. ·
The vehicle is driven at a constant speed. |
| Engine Revolution | Engine speed | Min.: 0 rpm
Max.: 8160 rpm |
No significant fluctuation. | The engine is running at a constant speed. |
| Motor Actual Current | Current to motor | Min.: -128 A
Max.: 127 A |
Value changes in proportion to steering effort. | The engine is running and the steering wheel is being turned. |
| Command Value Current | Amount of current requested for motor | Min.: -128 A
Max.: 127 A |
Value changes in proportion to steering effort. | The engine is running and the steering wheel is being turned. |
| Thermistor Temperature | ECU substrate temperature | Min.: -50°C (-58°F)
Max.: 205°C (401°F) |
- | The ignition switch to ON. |
| PIG Power Supply | Power source voltage to activate motor | Min.: 0.0 V
Max.: 25.5 V |
11 to 14 V | The engine is running and the power steering is operating. |
| IG Power Supply | ECU power source voltage | Min.: 0.0 V
Max.: 25.5 V |
11 to 14 V | The ignition switch to ON. |
| TRQ1 Zero Point Value | Zero point value of torque sensor 1 | Min.: 0.0000 V
Max.: 4.9725 V |
2.3 to 2.7 V | The engine is running and the steering wheel is not being turned. |
| TRQ2 Zero Point Value | Zero point value of torque sensor 2 | Min.: 0.0000 V
Max.: 4.9725 V |
2.3 to 2.7 V | The engine is running and the steering wheel is not being turned. |
| Motor Terminal Volt(+) | Motor terminal M1 voltage | Min.: 0.0 V
Max.: 25.5 V |
11 to 14 V: The engine is running and the steering wheel is being turned to the right.
6 to 11 V: The engine is running and the steering wheel is being turned to the left. |
- |
| Motor Terminal Volt(-) | Motor terminal M2 voltage | Min.: 0.0 V
Max.: 25.5 V |
6 to 11 V: The engine is running and the steering wheel is being turned to the right.
11 to 14 V: The engine is running and the steering wheel is being turned to the left. |
- |
| Control Mode | Codes indicating DTC detection timing during ECU control displayed in hexadecimal | - | - | - |