Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2013.08–2017.10
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0090108 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  DTC CHECK / CLEAR  


CHECK DTC (USING THE GTS)


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Trouble Codes.

Chassis > EMPS > Trouble Codes
50001 13

f.

Read the DTCs by following the display on the GTS.



CHECK DTC (USING SST CHECK WIRE)


a.

Turn the ignition switch off.


b.
C248264C19
1.625,0.813 1.625,0.406 true 1.865,1.854 1.865,1.479 true 1.49,0.219 1.719,0.365 0.229,0.146 10 false CG 1.75,1.875 1.969,2.021 0.219,0.146 10 false TC 0.177,0.042 0.333,0.219 0.156,0.177 10 false *1
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


c.

Turn the ignition switch to ON.


d.

Read and write down any DTCs indicated by the power steering warning light on the combination meter assembly.

HINT:
·

If normal, a 2 Hz blinking pattern repeats.


·

If there is only 1 DTC, the DTC will be output with a 4 second pause afterward. If there are several DTCs, the DTCs will be output with a 2.5 second pause between each code. Once all of the DTCs are output, there is a 4 second pause and the DTCs are output again.


·

If two or more malfunctions are detected simultaneously, DTCs will be displayed in ascending numerical order.




e.

Check the details of the DTCs.



Power Steering System
Power Steering Warning Light Display GTS Display
11 C1511
12 C1512
13 C1513
14 C1514
15 C1515
16 C1516
17 C1517
24 C1524
31 C1531
32 C1532
33 C1533
34 C1534
35 C1535
41 C1541
42 C1542
44 C1544
45 C1545
51 C1551
52 C1552
53 C1553
54 C1554
55 C1555
81 C1581

CLEAR DTC (USING THE GTS)


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Trouble Codes.


f.

Clear the DTCs by following the display on the GTS.

Chassis > EMPS > Clear DTCs
50002 13

g.

Turn the ignition switch off.


h.

Disconnect the GTS from the DLC3.



CLEAR DTC (USING SST CHECK WIRE)


a.

Turn the ignition switch off.


b.
C248264C17
1.604,0.802 1.594,0.354 true 1.354,1.833 1.594,1.51 true 2.063,1.823 1.854,1.49 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *1 1.5,0.156 1.813,0.354 0.313,0.198 10 false CG 1.292,1.854 1.604,2.052 0.313,0.198 10 false TS 2.01,1.854 2.323,2.052 0.313,0.198 10 false TC
*1 DLC3


Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3, and also terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


c.

Turn the ignition switch to ON.


d.

Disconnect and reconnect terminal 13 (TC) of the DLC3 4 times or more within 8 seconds.


e.

Check that the power steering warning light blinks a code to indicate normality.


f.

Turn the ignition switch off.


g.

Remove SST from the DLC3.