Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2013.08–2017.10
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0090108 POWER STEERING SYSTEM D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  CALIBRATION  


TORQUE SENSOR ZERO POINT CALIBRATION (USING THE GTS)


NOTICE:

Perform torque sensor zero point calibration if any of the following conditions is met:

·

The electric power steering column sub-assembly (containing the torque sensor) has been replaced.

·

The power steering motor assembly has been replaced.

·

The power steering ECU assembly has been replaced.

·

There is a difference in steering effort between turning right and turning left.



a.

Inspection before calibration.

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Chassis / EMPS / Data List.


vi.

Check the values by referring to the table below.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG Power Supply ECU power source voltage Min.: 0.0 V
Max.: 25.5 V
11 to 14 V The ignition switch to ON.
Standard voltage:

11 to 14 V


NOTICE:

If the IG power supply voltage is 9 V or less, calibration cannot be performed. In this case, charge or replace the battery, and then perform calibration.




b.

Perform torque sensor zero point calibration.

NOTICE:

If DTC C1516 (Torque Sensor Zero Point Adjustment Incomplete) is stored, the torque sensor zero point cannot be calibrated. Clear the DTC before starting calibration.


i.

Set the steering wheel to the center point and align the front wheels straight ahead.


ii.

Turn the ignition switch off.


iii.

Connect the GTS to the DLC3.


iv.

Turn the ignition switch to ON.


v.

Turn the GTS on.


vi.

Calibrate the power steering ECU assembly. Enter the following menus: Chassis / EMPS / Utility / Torque Sensor Adjustment.

Chassis > EMPS > Utility
Tester Display
Torque Sensor Adjustment
50005 13 517
NOTICE:
·

Do not touch the steering wheel during torque sensor zero point calibration.

·

Perform calibration only when the vehicle is stopped.






TORQUE SENSOR ZERO POINT CALIBRATION (USING SST CHECK WIRE)


NOTICE:

Perform torque sensor zero point calibration if any of the following conditions is met:

·

The electric power steering column sub-assembly (containing the torque sensor) has been replaced.

·

The power steering motor assembly has been replaced.

·

The power steering ECU assembly has been replaced.

·

There is a difference in steering effort between turning right and turning left.



a.

Inspection before calibration.

i.

Turn the ignition switch off.


ii.

Disconnect the power steering ECU assembly connector.


iii.

Turn the ignition switch to ON.


iv.
C266275C04
0.49,0.188 0.906,0.469 0.417,0.281 0.854,2.302 1.198,2.156 true 0.198,0.156 0.51,0.354 0.313,0.198 10 false *a 1.24,2.073 1.698,2.271 0.458,0.198 10 false IG 0.573,0.24 0.885,0.438 0.313,0.198 10 false F12
*a Rear view of wire harness connector (to Power Steering ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F12-1 (IG) - Body ground Ignition switch ON 11 to 14 V


NOTICE:

If the IG power supply voltage is 9 V or less, calibration cannot be performed. In this case, charge or replace the battery, and then perform calibration.



v.

Turn the ignition switch off.


vi.

Connect the power steering ECU assembly connector.



b.

Clear sensor calibration value.

i.

Set the steering wheel to the center point and align the front tires straight ahead.


ii.

Turn the ignition switch off.


iii.
C248264C17
1.604,0.802 1.594,0.354 true 1.354,1.833 1.594,1.51 true 2.063,1.823 1.854,1.49 true 0.146,0.146 0.458,0.344 0.313,0.198 10 false *1 1.5,0.156 1.813,0.354 0.313,0.198 10 false CG 1.292,1.854 1.604,2.052 0.313,0.198 10 false TS 2.01,1.854 2.323,2.052 0.313,0.198 10 false TC
*1 DLC3


Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3, turn the ignition switch to ON and connect and disconnect terminals 13 (TC) and 4 (CG) of the DLC3 20 times or more within 20 seconds.

SST
09843-18040  

NOTICE:

Connect the terminals to the correct positions to avoid a malfunction.



iv.

Check that the power steering warning light blinks and then remains illuminated.

HINT:

The power steering warning light illumination indicates that DTC C1515/15 has been stored.



v.

Turn the ignition switch off.

NOTICE:

After clearing the sensor calibration value zero point calibration cannot be performed if the ignition switch is ON.




c.

Perform torque sensor zero point calibration.

NOTICE:

If DTC C1516/16 is stored, the torque sensor zero point cannot be calibrated. Clear the DTC before starting calibration.


i.

Set the steering wheel to the center point and align the front tires straight ahead.


ii.

Turn the ignition switch off.


iii.
C248264C18
1.625,0.813 1.625,0.406 true 1.635,1.854 1.635,1.479 true 1.49,0.219 1.719,0.365 0.229,0.146 10 false CG 1.521,1.875 1.74,2.021 0.219,0.146 10 false TS 0.177,0.042 0.333,0.219 0.156,0.177 10 false *1
*1 DLC3


Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

SST
09843-18040  


iv.

Turn the ignition switch to ON.

NOTICE:
·

Do not touch the steering wheel during torque sensor zero point calibration (for 7 seconds).


·

Perform calibration only when the vehicle is stopped.



HINT:

The power steering warning light blinks (0.125 seconds on and 0.125 seconds off) after calibration has completed.