Home › Steering › STEERING COLUMN › STEERING SYSTEM
RM30M0E _55 Steering _017104 STEERING COLUMN _0090112 STEERING SYSTEM N

STEERING COLUMN  STEERING SYSTEM  ADJUSTMENT  


PROCEDURE

Hide 1. STEERING OFF CENTER ADJUSTMENT PROCEDURE

HINT:

This is the adjustment procedure for when the steering is off center.


a.

Inspect steering wheel off center.

i.
C286505
2.76,0.635 3.01,0.302 3.01,0.302 2.677,0.542 true 3.063,0.198 3.302,0.354 0.24,0.156 10 true *a
*a Masking Tape


Apply masking tape to the top center of the steering wheel assembly and upper steering column cover.


ii.

Drive the vehicle in a straight line for 100 m (328 ft.) at a constant speed of 56 km/h (35 mph) and hold the steering wheel to maintain course.


iii.
C286506
2.51,0.448 2.344,0.292 true 2.219,0.615 2.49,0.677 true 2.74,0.625 3.073,0.75 3.073,0.75 2.729,0.448 true 2.198,0.198 2.365,0.354 0.167,0.156 10 true *1 2.073,0.521 2.26,0.677 0.188,0.156 10 true *2 3.115,0.708 3.302,0.865 0.188,0.156 10 true *a
*1 Upper Steering Column Cover
*2 Steering Wheel Assembly
*a Marked Line


Draw a line on the masking tape as shown in the illustration.


iv.

Turn the steering wheel assembly to the center position.

HINT:

Look at the upper surface of the steering wheel assembly, steering spoke and SRS airbag or horn button assembly line to find the center position.



v.
C286507
2.354,0.25 2.531,0.427 true 2.271,0.552 2.49,0.677 true 2.75,0.448 3.042,0.302 3.042,0.302 2.74,0.615 true 2.198,0.146 2.396,0.302 0.198,0.156 10 true *1 2.115,0.469 2.323,0.625 0.208,0.156 10 true *2 3.073,0.188 3.271,0.354 0.198,0.167 10 true *a
*1 Upper Steering Column Cover
*2 Steering Wheel Assembly
*a Marked Line


Draw a new line on the masking tape on the steering wheel assembly as shown in the illustration.


vi.

Measure the distance between the 2 lines on the masking tape on the steering wheel assembly.


vii.

Convert the measured distance to a steering angle value.

HINT:
·

Measured distance 1 mm (0.0394 in.) = Steering angle of approximately 1°.

·

Make a note of the steering angle.





b.

Adjust the steering angle.

i.
C283333C02
0.646,1.302 0.938,1.792 0.938,1.792 1,1.292 true 0.906,1.865 1.219,2.021 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the RH and LH tie rod ends and rack ends respectively where they can be easily seen.


ii.
C230944

Using a paper gauge, measure the distance from the RH and LH tie rod ends to the rack end screws.

HINT:
·

Measure both the RH and LH sides.

·

Make a note of the measured values.




iii.

Remove the RH and LH steering rack boot clips from the rack boots.


iv.

Loosen the RH and LH lock nuts.


v.

Turn the RH and LH rack ends by the same amount (but in different directions) according to the steering angle value.

HINT:

One turn (360°) of a rack end (1.5 mm (0.0591 in.) horizontal movement) is equal to a 10.8° change in steering angle.



vi.

Tighten the RH and LH lock nuts to the specified torque.

Torque:
74.5 N*m (760 kgf*cm, 55 ft.*lbf)

NOTICE:

Make sure that the difference in length between the RH and LH tie rod ends and rack end screws is within 1.5 mm (0.0591 in.).



vii.

Install the RH and LH steering rack boot clips.