Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › 2013.08–2016.04
RM30M0E _55 Steering _017104 STEERING COLUMN _0090116 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Refer to Service Bulletin for the installation position of the transponder key ECU assembly.


PROCEDURE

Hide 80960 1.INSTALL POWER STEERING MOTOR ASSEMBLY

NOTICE:
·

Do not drop the power steering motor assembly, strike it with tools or subject it to impacts.

·

If the power steering motor assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness of the power steering motor assembly.

·

Do not allow any moisture to come into contact with the power steering motor assembly.

·

Do not allow any foreign objects to contaminate the steering column assembly and the power steering motor assembly.



a.
C243731

Apply the grease that is supplied with a new steering column assembly or power steering motor assembly to the serrated part of the steering column assembly.


b.

Temporarily install the power steering motor assembly to the steering column assembly with the 2 bolts.

NOTICE:

When temporarily installing the 2 bolts to the power steering motor assembly, do not tighten them all the way down.



c.
C287505C01
0.771,1.51 1.094,1.646 true 0.771,0.833 1.615,1.083 true 0.583,1.396 0.771,1.552 0.188,0.156 10 false *a 0.448,0.729 0.802,0.896 0.354,0.167 10 false SST
*a Wooden Block


Secure the steering column assembly in a vise using aluminum plates and wooden blocks.

NOTICE:

Do not overtighten the vise.



d.

Using SST, turn the steering main shaft once 180 degrees to the left and then 180 degrees to the right at a speed of 60 rpm, and repeat 2 to 3 times to adjust the axis centering of the power steering motor assembly.

SST
09616-00011  


e.

Tighten the 2 bolts.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


f.

Using SST, measure the turning torque of the steering main shaft.

Standard preload:

1.42 N*m (14 kgf*cm, 13 in.*lbf) or less


NOTICE:

Ensure that there is no abnormal resistance during rotation.


If the turning torque is not as specified, readjust the axis centering of the power steering motor assembly.


Hide 84450 2.INSTALL IGNITION OR STARTER SWITCH ASSEMBLY (w/o Smart Entry and Start System)

a.
C232531

Engage the 2 claws and install the ignition or starter switch assembly to the upper steering column bracket assembly.


Hide 85432 3.INSTALL KEY INTERLOCK SOLENOID (for Automatic Transaxle without Smart Entry and Start System)

a.
C287270

Engage the claw to install the key interlock solenoid to the upper steering column bracket assembly.


b.

Install the screw.


Hide 84052 4.INSTALL UNLOCK WARNING SWITCH ASSEMBLY (w/o Smart Entry and Start System)

a.
C287271

Engage the 2 claws and install the unlock warning switch assembly.

HINT:

Slide the unlock warning switch assembly in the direction shown by the arrow in the illustration to install it.



Hide 69057A 5.INSTALL IGNITION SWITCH LOCK CYLINDER AND KEY SET (w/o Smart Entry and Start System)

a.

Secure the steering column assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C294148

Install the ignition switch lock cylinder and key set with a new steering lock set bolt, and then tighten the steering lock set bolt until its head comes off.


Hide 45020A 6.INSTALL STEERING LOCK ACTUATOR ASSEMBLY (w/ Smart Entry and Start System)

a.

Secure the steering column assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C294148

Install the steering lock actuator assembly with a new steering lock set bolt, and then tighten the steering lock set bolt until its head comes off.


Hide 45260 7.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C285110C02
0.896,1.104 1.469,1.146 true 0.927,0.552 1.656,0.75 true 0.708,0.438 1.021,0.594 0.313,0.156 10 false *a 0.667,1.042 0.885,1.198 0.219,0.156 10 false *b
*a Alignment Mark
*b Slit


Align the slit of the No. 2 steering intermediate shaft assembly with the alignment mark of the steering column assembly.


b.

Install the No. 2 steering intermediate shaft assembly to the steering column assembly with the bolt.

Torque:
35.3 N*m (360 kgf*cm, 26 ft.*lbf)


Hide 45209 8.INSTALL STEERING SLIDING YOKE SUB-ASSEMBLY

a.
C232525C05
1.875,0.875 2.51,0.698 2.51,0.698 1.927,0.729 true 2.604,0.604 2.917,0.76 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering sliding yoke sub-assembly and temporarily install them with the bolt.


Hide 89658 9.INSTALL POWER STEERING ECU BRACKET

a.

Install the power steering ECU bracket to the steering column assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)