Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › SFI SYSTEM(for Automatic Transaxle) › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017071 1NZ-FE ENGINE CONTROL _0090157 SFI SYSTEM(for Automatic Transaxle) C

1NZ-FE ENGINE CONTROL  SFI SYSTEM(for Automatic Transaxle)  P0500  Vehicle Speed Sensor  


DESCRIPTION

The wheel speed sensors monitor the wheel rotation speed and send signals to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

HINT:
·

Various systems use the vehicle speed signal distributed from the combination meter assembly. Check all the components possibly related to speed signal.

·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.



A115899E57
0.771,1.052 1.563,1.427 0.792,0.375 10 false from Speed Sensor 1.833,1.854 3.417,2.417 1.583,0.563 10 false Skid Control ECU 3.5,1.885 5.333,2.052 1.833,0.167 10 false Combination Meter Assembly 3.115,0.604 3.927,0.781 0.813,0.177 10 false 4-Pulse 5.042,0.604 5.854,0.781 0.813,0.177 10 false 4-Pulse 6.073,1.844 6.521,2.01 0.448,0.167 10 false ECM 1.813,2.021 3.5,2.208 1.688,0.188 10 false (Brake Actuator Assembly)

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0500 Vehicle Speed Sensor While vehicle is being driven, no vehicle speed sensor signal is sent to the ECM (1 trip detection logic).
·

Open or short in speed signal circuit

·

Combination meter assembly

·

Skid control ECU (Brake actuator assembly)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM assumes that the vehicle is being driven when the indicated engine speed is more than 2120 rpm and 30 seconds have elapsed since the park/neutral position switch was turned off (typical example value). If there is no speed signal from the combination meter, despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Vehicle speed sensor
Combination meter assembly
Skid control ECU (Brake actuator assembly)
Required Sensors/Components (Related) Park/neutral position switch
Engine coolant temperature sensor
Crankshaft position sensor
Throttle position sensor
Mass air flow meter
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Ignition Switch ON
Time after ignition switch OFF to ON 3 seconds or more
Battery voltage 11 V or higher
Starter OFF
Time after park/neutral position switch turned off 30 seconds

TYPICAL MALFUNCTION THRESHOLDS

Vehicle speed sensor signal No signal

CONFIRMATION DRIVING PATTERN

A240416E10
0.661,0.879 1.859,1.105 1.198,0.226 10 24 km/h (14 mph) 1.421,2.049 1.82,2.219 0.399,0.17 10 Idling 0.596,2.399 1.773,2.583 1.177,0.184 10 Ignition Switch ON 2.387,2.273 2.62,2.443 0.233,0.17 10 [A] 4.706,0.473 4.911,0.643 0.205,0.17 10 [B] 6.249,3.287 6.447,3.485 0.198,0.198 10 [D] 6.062,1.12 6.26,1.318 0.198,0.198 10 [C] 4.012,3.052 5.817,3.197 1.805,0.146 10 Total of 30 seconds or more 4.32,3.453 5.512,3.599 1.192,0.146 10 5 seconds or more 6.084,2.945 5.902,3.529 5.902,3.529 5.533,3.529 false

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

On the GTS, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / Idle Fuel Cut.

8.

Drive the vehicle at 24 km/h (14 mph) or more for a total of 30 seconds or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

10.

Stop the vehicle.

11.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

14.

Input the DTC: P0500.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A301714E09
2.396,1.531 2.854,1.729 0.458,0.198 10 false F38 3.927,1.531 4.385,1.729 0.458,0.198 10 false F38 5.146,1.531 5.604,1.729 0.458,0.198 10 false F82 5.958,2.271 6.417,2.469 0.458,0.198 10 false ECM 6.073,1.115 6.531,1.313 0.458,0.198 10 false 5V 5.458,1.438 5.917,1.635 0.458,0.198 10 false SPD 3.667,1.531 4.125,1.729 0.458,0.198 10 false +S 2.719,1.521 3.177,1.719 0.458,0.198 10 false SI 2.448,1.344 2.906,1.542 0.458,0.198 10 false 34 3.979,1.354 4.438,1.552 0.458,0.198 10 false 35 5.188,1.344 5.646,1.542 0.458,0.198 10 false 18 5.302,2.781 6.417,3.01 1.115,0.229 10 false to Other ECUs 0.208,1.5 2.083,1.823 1.875,0.323 10 false from Skid Control ECU (Brake Actuator Assembly) 2.385,2.24 4.208,2.594 1.823,0.354 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Vehicle Speed
50003 234 10

d.

Drive the vehicle.


e.

Read the value displayed on the GTS.


Result:
Result Proceed to
Values displayed on GTS and speedometer display not equal A
Values displayed on GTS and speedometer display equal B



A

2.CHECK COMBINATION METER SYSTEM (SPEED SIGNAL CIRCUIT)

B

2.CHECK COMBINATION METER SYSTEM (SPEED SIGNAL CIRCUIT)
a.

Check the circuits that send vehicle speed signals to this system in the combination meter system.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speed Signal Circuit


Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

If DTCs (pending DTCs) are not output to the GTS, the repair has been successfully completed.



Result:
Proceed to
NEXT



NEXT

END