Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2013.08–2017.10
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  DTC CHECK / CLEAR  


DTC CHECK/CLEAR (When Using GTS)


a.

Check the DTCs.

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Read the DTCs following the prompts on the GTS. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105



b.

Clear the DTCs.

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Operate the GTS to clear the codes. Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.


vi.

Press the DTC clear button.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

vii.

According to the display on the GTS, select the trouble code data display with the clear button.




DTC CHECK/CLEAR (When Using SST Check Wire)


a.
C280109C37
1.615,0.813 1.979,0.396 true 1.427,1.875 1.823,1.479 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *1 2,0.302 2.313,0.5 0.313,0.198 10 false CG 1.229,1.802 1.5,2 0.271,0.198 10 false TC
*1 DLC3


Check the DTCs.

i.

Turn the ignition switch off.


ii.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


iii.

Turn the ignition switch to ON.


iv.

Observe the blinking pattern of the ABS warning light in order to identify the DTC.

HINT:

If no code appears, inspect the 13 (TC) and 4 (CG) terminal circuit, and ABS warning light circuits.


Trouble Area See Procedure
TC and CG terminal circuit (Click here)
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)

HINT:
·

When the system is operating correctly, each light will blink continuously in a pattern of 0.25 seconds on, and then 0.25 seconds off.

·

When one DTC is output, each light will output the same code at 4 second intervals (for example, code 21 would be output as 2 flashes, a 1.5 second pause, and then 1 flash).

·

When 2 or more DTCs are output, each light will output a different code at 2.5 second intervals, and when all codes have been output, there will be a 4 second pause and the sequence will repeat.

·

When multiple codes are stored, they are output in order starting with the lowest DTC number.




v.

Check the details of the DTCs.

ABS DTC
ABS Warning Light Display GTS Display
11 C146E
12 C146F
13 C146C
14 C146D
21 C1468
22 C1469
23 C146A
24 C146B
31 C1401
C1405
32 C1402
C1406
33 C1403
C1407
34 C1404
C1408
35 C1413
36 C1414
38 C1415
39 C1416
41 C1241
C1417
49 C1425
51 C1427
C1428
94 U0073


vi.

After completing the check, disconnect terminals 13 (TC) and 4 (CG) of the DLC3 to turn off the display.

HINT:

If 2 or more DTCs are detected at the same time, the DTCs will be displayed in ascending order.




b.

Clear the DTCs.

i.

Turn the ignition switch off.


ii.
C280109C38
1.5,1.875 1.844,1.49 true 1.615,0.781 1.958,0.396 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *1 1.99,0.302 2.302,0.5 0.313,0.198 10 false CG 1.281,1.813 1.552,2.01 0.271,0.198 10 false TC
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


iii.

Turn the ignition switch to ON.


iv.

Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.


v.

Check that the warning light indicates a normal system code.


vi.

Remove SST from the terminals of the DLC3.

HINT:

Clearing the DTCs cannot be performed by disconnecting the battery terminal or the IG1 NO. 2 fuse.





END OF DTC CHECK/CLEAR


a.

Turn the ignition switch to ON.


b.

Check that the ABS warning light go off within approximately 3 seconds after turning the ignition switch to ON.