Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2013.08–2016.04
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TERMINALS OF ECU  


TERMINALS OF ECU


C280110C06
0.813,0.49 1.125,0.646 0.313,0.156 10 false *a
*a Component without harness connected
(Skid Control ECU (Brake Actuator Assembly))
- -


Terminal No. (Symbol) Terminal Description
1 (GND1) Skid control ECU ground
2 - (Not used)
3 - (Not used)
4 (RL-) Rear wheel speed LH (-) signal input
5 (RL+) Rear wheel speed LH (+) power supply output
6 (FR-) Front wheel speed RH (-) signal input
7 (FR+) Front wheel speed RH (+) power supply output
8 - (Not used)
9 - (Not used)
10 - (Not used)
11 - (Not used)
12 (+BS) Solenoid relay power supply
13 (GND2) Pump motor ground
14 (CANL) CAN communication line L
15 - (Not used)
16 (RR-) Rear wheel speed RH (-) signal input
17 (RR+) Rear wheel speed RH (+) power supply output
18 (FL-) Front wheel speed LH (-) signal input
19 (FL+) Front wheel speed LH (+) power supply output
20 - (Not used)
21 - (Not used)
22 (SP1) Speed signal output for speedometer
23 - (Not used)
24 (+BM) Motor relay power supply
25 (CANH) CAN communication line H
26 - (Not used)
27 - (Not used)
28 (STP) Stop light switch input
29 - (Not used)
30 - (Not used)
31 - (Not used)
32 (TS) Sensor diagnosis check input
33 - (Not used)
34 (IG1) ECU power supply


TERMINAL INSPECTION


a.

Disconnect the connector and measure the voltage or resistance on the wire harness side.

C280111
1.427,1.49 1.781,1.719 0.354,0.229 0.625,0.427 0.938,0.583 0.313,0.156 10 false *a 1.448,1.51 1.781,1.708 0.333,0.198 10 false A35
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))
- -


HINT:

Voltage cannot be measured with the connector connected to the skid control ECU (brake actuator assembly) as the connector is watertight.


Standard:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A35-1 (GND1) - Body ground W-B - Body ground Skid control ECU ground Always Below 1 Ω
A35-12 (+BS) - Body ground W - Body ground Solenoid relay power supply Always 11 to 14 V
A35-13 (GND2) - Body ground W-B - Body ground Pump motor ground Always Below 1 Ω
A35-24 (+BM) - Body ground B - Body ground Motor relay power supply Always 11 to 14 V
A35-25 (CANH) - A35-14 (CANL) L - W CAN bus Ignition switch off 54 to 69 Ω
A35-28 (STP) - Body ground G - Body ground Stop light switch input Stop light switch ON → OFF
(Brake pedal depressed → released)
7.5 to 14 V
→ Below 1.5 V
A35-34 (IG1) - Body ground L - Body ground ECU power supply Ignition switch ON 11 to 14 V