Home › Engine / Hybrid System › 1NZ-FE STARTING › STARTER › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017085 1NZ-FE STARTING _0090212 STARTER G

1NZ-FE STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used.

If not, the cable may became hot and cause injury.


NOTICE:

Perform each of the following tests within 3 to 5 seconds to prevent the coil from burning out.


a.

Perform a pull-in test.

i.
A310451

Remove the nut to disconnect the lead wire from the terminal C.


ii.
A156601C03
0.917,0.792 1.375,1.219 false 3.042,0.75 2.74,1.458 true 2.385,1.594 1.823,2.521 true 0.729,0.708 1.042,0.865 0.313,0.156 10 false *a 3.052,0.625 3.365,0.781 0.313,0.156 10 false *b 1.656,2.417 1.969,2.573 0.313,0.156 10 false *c
*a Starter Body
*b Terminal C
*c Terminal 50


Connect the battery to the magnet starter switch assembly as shown in the illustration. Check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move outward, replace the magnet starter switch assembly.



b.

Perform a holding test.

i.
A156602C03
1,0.74 1.385,1.26 false 3.042,0.698 2.708,1.458 true 2.031,2.354 2.396,1.583 true 0.802,0.656 1.115,0.813 0.313,0.156 10 false *a 3.042,0.552 3.354,0.708 0.313,0.156 10 false *b 1.833,2.271 2.146,2.427 0.313,0.156 10 false *c
*a Starter Body
*b Terminal C
*c Terminal 50


Check that the pinion gear does not return inward after the lead is disconnected from the terminal C.

If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



c.

Check return operation.

i.
A156603C03
0.917,0.813 1.375,1.188 false 3,0.854 2.729,1.458 true 1.938,2.406 2.417,1.594 true 0.729,0.729 1.042,0.885 0.313,0.156 10 false *a 3.01,0.708 3.323,0.865 0.313,0.156 10 false *b 1.74,2.302 2.052,2.458 0.313,0.156 10 false *c
*a Starter Body
*b Terminal C
*c Terminal 50


Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear moves inward.

If the clutch pinion gear does not move inward, replace the magnet starter switch assembly.



d.

Perform a no-load performance test.

i.
A310451

Connect the lead wire to terminal C with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


ii.

Clamp the starter assembly in a vise between aluminum plates.

NOTICE:

Ensure that the starter is secured in the vise to prevent it from falling out.



iii.
A156604C04
1.073,0.979 1.344,1.219 false 2.542,1.396 2.76,2.542 true 1.719,2.292 2.135,1.615 true 0.896,0.885 1.208,1.042 0.313,0.156 10 false *a 1.521,2.198 1.833,2.354 0.313,0.156 10 false *b 2.74,2.573 3.052,2.729 0.313,0.156 10 false *c 2.802,0.708 3.115,0.906 0.313,0.198 10 false *d
*a Starter Body
*b Terminal 50
*c Terminal 30
*d Ammeter


Connect the battery and an ammeter to the starter assembly as shown in the illustration.

NOTICE:

Do not allow any lead to get caught as the pinion gear operates.



iv.

Check that the starter operates smoothly and steadily with the pinion gear moving outward.

Measure the current according to the value(s) in the table below.

Standard Current:
Tester Connection Condition Specified Condition
Battery positive terminal - Terminal 30 - Terminal 50 11.5 V 90 A or less


If the result is not as specified, repair or replace the starter assembly.



Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for an open circuit.

i.
A305603C02
2.26,1.177 3.042,0.958 3.042,0.958 2.385,0.948 true 3.073,0.875 3.385,1.073 0.313,0.198 10 false *a
*a Segment


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



b.

Check the commutator for a short circuit.

i.
A305604C02
0.833,1.135 1.563,0.917 true 1.865,1.635 2.26,1.156 true 1.74,1.615 2.052,1.771 0.313,0.156 10 false *a 0.615,1.063 0.927,1.219 0.313,0.156 10 false *b
*a Segment
*b Starter Armature Core


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Starter Armature Core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



c.

Check the commutator appearance.

If the surface is dirty or burnt, restore it with sandpaper (No. 400) or on a lathe.


d.

Check the commutator for runout.

i.
A302937

Place the commutator on V-blocks.


ii.

Using a dial indicator, measure the runout.

Maximum runout:

0.05 mm (0.00197 in.)


If the runout is greater than the maximum, replace the starter armature assembly.



e.
A305623C02
0.271,0.469 0.583,0.667 0.313,0.198 10 false *a
*a Diameter


Using a vernier caliper, measure the commutator diameter.

Standard diameter:

28.0 mm (1.102 in.)


Minimum diameter:

27.0 mm (1.063 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


f.
A302939C02
3.229,0.875 3.427,1.073 0.198,0.198 10 false *a
*a Undercut Depth


Check that the undercut portion between the segments is free of foreign matter and measure its depth.

Standard undercut depth:

0.6 mm (0.0236 in.)


Minimum undercut depth:

0.2 mm (0.00787 in.)


If the undercut depth is less than the minimum, adjust it with a hacksaw blade.


Hide 28120 3.INSPECT STARTER YOKE ASSEMBLY

a.

Check the field coil for an open circuit.

i.
A153760C04
1.646,0.531 1.958,0.688 0.313,0.156 10 false *a 0.896,0.958 1.208,1.115 0.313,0.156 10 false *b
*a Field Coil Brush Lead
*b Lead Wire


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Lead Wire - Field Coil Brush Lead Always Below 1 Ω


If the result is not as specified, replace the starter yoke assembly.



b.

Check the field coil for a short circuit.

i.
A153777C04
1.615,0.458 1.813,0.615 0.198,0.156 10 false *a 1.219,1.385 1.458,1.563 0.24,0.177 10 false *b
*a Field Coil Brush Lead
*b Starter Yoke Body


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Field Coil Brush Lead - Starter Yoke Body Always 10 kΩ or higher


If the result is not as specified, replace the starter yoke assembly.



Hide 4.INSPECT BRUSH

a.
A302940

Using a vernier caliper, measure the brush length.

Standard length:

14 mm (0.551 in.)


Minimum length:

9 mm (0.354 in.)


If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.


Hide 28140 5.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.

Check the starter brush holder for a short circuit.

i.
A153747E07
2.052,0.656 2.677,0.656 true 0.948,1.271 0.458,1.271 true 1.031,0.563 0.573,0.313 false 2.042,1.323 2.677,1.563 false 2.021,1.313 2.677,1.563 true 2.677,1.479 2.917,1.646 0.24,0.167 10 false (+) 0.302,0.229 0.542,0.396 0.24,0.167 10 false (+) 0.281,1.177 0.521,1.344 0.24,0.167 10 false (-) 2.698,0.563 2.938,0.729 0.24,0.167 10 false (-)

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) Brush Holder - Negative (-) Brush Holder Always 10 kΩ or higher


If the result is not as specified, replace the starter brush holder assembly.



Hide 28021 6.INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.

Check the starter center bearing clutch sub-assembly.

i.
A153746C05
1.385,0.313 1.698,0.469 0.313,0.156 10 *a 1.417,1.615 1.729,1.771 0.313,0.156 10 *b
*a Free
*b Lock


While holding the starter center bearing clutch sub-assembly, rotate the pinion gear clockwise, and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

If the operation is not as specified, replace the starter center bearing clutch sub-assembly.



Hide 28150 7.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.

Check the plunger.

i.
A302941

Push in the plunger and check that it returns quickly to its original position.

NOTICE:

To avoid damaging the inside of the magnet starter switch assembly, do not release the plunger quickly.


If the operation is not as specified, replace the magnet starter switch assembly.



b.
A194284C05
1.833,0.688 2.094,0.583 false 1.188,1.594 1.583,1.167 true 2.146,0.51 2.458,0.667 0.313,0.156 10 false *a 1.021,1.552 1.333,1.708 0.313,0.156 10 false *b
*a Terminal 50
*b Terminal C


Check the pull-in coil for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the magnet starter switch assembly.



c.
A194285C05
0.698,1.729 1.094,1.458 false 2.021,1.094 2.333,1.031 false 2.427,0.958 2.74,1.115 0.313,0.156 10 false *a 0.51,1.646 0.823,1.802 0.313,0.156 10 false *b
*a Terminal 50
*b Magnet Starter Switch Body


Check the holding coil for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Magnet Starter Switch Body Always Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.