Home › Engine / Hybrid System › 1NZ-FE STARTING › STARTER › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017085 1NZ-FE STARTING _0090212 STARTER A

1NZ-FE STARTING  STARTER  DISASSEMBLY  


PROCEDURE

Hide 28150 1.REMOVE MAGNET STARTER SWITCH ASSEMBLY

a.
A310451

Remove the nut to disconnect the lead wire from the terminal C.


b.
A182596

Remove the 2 nuts that hold the magnet starter switch assembly from the starter drive housing.


c.
A156359C07
1.281,0.646 1.438,0.156 false 0.906,0.792 0.51,0.208 false 0.313,0.125 0.479,0.292 0.167,0.167 10 false *1 1.5,0.073 1.667,0.24 0.167,0.167 10 false *a
*1 Starter Pinion Drive Lever
*a Hook


While lifting the rear of the magnet starter switch assembly, remove the hook from the starter pinion drive lever, then remove the magnet starter switch assembly.


Hide 28120 2.REMOVE STARTER YOKE ASSEMBLY

a.
A288934

Remove the 2 through bolts, and pull out the starter yoke assembly together with starter armature assembly.


Hide 28140 3.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A305622C02
1.938,1.906 2.302,1.906 false 2.365,1.823 2.677,1.979 0.313,0.156 10 false *1
*1 Dust Protector


Remove the 2 screws, hold down the lead wire and remove the commutator end frame.

NOTICE:

To avoid interference between the starter brush holder assembly and dust protector, tilt the commutator end frame while removing it.



b.
A302950

Using a screwdriver, hold the spring back to disconnect the starter brush holder assembly.


c.

Disconnect the 4 brushes to remove the starter brush holder assembly.


Hide 28160 4.REMOVE STARTER ARMATURE ASSEMBLY

a.

Remove the starter armature assembly from the starter yoke assembly.


Hide 28021 5.REMOVE STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A156362C02
0.323,0.729 0.542,0.573 false 1.823,1.698 1.563,1.531 false 1.198,2.063 0.938,1.833 false 0.156,0.646 0.469,0.802 0.313,0.156 10 false *1 1.885,1.656 2.198,1.813 0.313,0.156 10 false *2 1.271,2.01 1.583,2.167 0.313,0.156 10 false *3
*1 Starter Pinion Driver Lever
*2 Starter Center Bearing Clutch Sub-assembly
*3 Shock Absorber


Remove the starter pinion driver lever and starter center bearing clutch sub-assembly with shock absorber from the starter drive housing.


b.
A302935

Using a screwdriver, tap the stop collar toward the starter center bearing clutch sub-assembly.


c.
A302936

Using a screwdriver, pry off the snap ring.


d.
A305594C02
2.781,0.5 2.979,0.708 false 1.729,0.563 2.083,0.771 false 1.01,1.688 1.427,1.865 false 2.604,0.406 2.917,0.563 0.313,0.156 10 false *1 1.51,0.469 1.823,0.625 0.313,0.156 10 false *2 1.531,1.802 1.844,1.958 0.313,0.156 10 false *3
*1 Stop Collar
*2 Starter Center Bearing Clutch Sub-assembly
*3 Shock Absorber


Remove the stop collar and starter center bearing clutch sub-assembly from the shock absorber.