Home › Engine / Hybrid System › 1NZ-FE STARTING › STARTER › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017085 1NZ-FE STARTING _0090212 STARTER A

1NZ-FE STARTING  STARTER  REASSEMBLY  


PROCEDURE

Hide 28021 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A288939C05
2.708,0.49 3,0.698 false 1.833,0.542 2.125,0.76 false 0.875,1.74 1.167,1.958 false 1.198,1.406 1.354,1.604 0.156,0.198 10 false . 2.542,0.406 2.854,0.604 0.313,0.198 10 false *1 1.656,0.438 1.969,0.635 0.313,0.198 10 false *2 1.229,1.906 1.542,2.104 0.313,0.198 10 false *3
*1 Stop Collar
*2 Starter Center Bearing Clutch Sub-assembly
*3 Shock Absorber
V100135

High-temperature Grease


Apply high-temperature grease to the bushing and spline of the starter center bearing clutch sub-assembly, shock absorber and stop collar.


b.
A302942

Place the starter center bearing clutch sub-assembly and stop collar to the shock absorber.


c.

Apply high-temperature grease to a new snap ring, and install it to the shock absorber groove.


d.
A302951

Using a vise, compress the snap ring.

NOTICE:

Do not overtighten the vise.



e.
A302943

Using a plastic-faced hammer, while holding the starter center bearing clutch sub-assembly, tap the shock absorber and install the stop collar to the snap ring.

NOTICE:

Do not tap the shock absorber too strongly.



f.
A305625C02
2.021,1.594 2.406,1.885 false 2.573,0.656 2.927,0.417 false 1.021,1.031 0.625,0.594 false 2.99,0.292 3.302,0.49 0.313,0.198 10 false *1 2.49,1.823 2.802,2.021 0.313,0.198 10 false *2 0.417,0.5 0.729,0.698 0.313,0.198 10 false *3
*1 Starter Pinion Driver Lever
*2 Starter Center Bearing Clutch Sub-assembly
*3 Shock Absorber
V100135

High-temperature Grease


Apply high-temperature grease to the parts of the starter pinion drive lever that contact the magnet starter switch assembly and starter clutch pivots.


g.

Install the starter pinion drive lever to the starter center bearing clutch sub-assembly.


h.
A156366C06
0.875,0.25 1.781,0.854 true 1.969,0.927 2.448,0.635 true 0.677,0.156 1.094,0.313 0.417,0.156 10 false *a 2.49,0.552 2.844,0.698 0.354,0.146 10 false *b
*a Cutout
*b Protrusion


Align the protrusion of the shock absorber with the cutout of the starter drive housing to install it.


Hide 28160 2.INSTALL STARTER ARMATURE ASSEMBLY

a.

Install the starter armature assembly to the starter yoke assembly.


Hide 28140 3.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.

Install the starter brush holder assembly.


b.
A302944

Using a screwdriver, hold the brush spring back to install the 4 brushes into the starter brush holder assembly.


c.
A302972C03
0,0 3.427,0 false
V100135

Spindle Oil


Apply spindle oil with additives to the bearing of the commutator end frame.


d.
A305622C02
1.938,1.906 2.302,1.906 false 2.365,1.823 2.677,1.979 0.313,0.156 10 false *1
*1 Dust Protector


Install the commutator end frame with the 2 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)

NOTICE:

To avoid interference between the starter brush holder assembly and dust protector, tilt the commutator end frame while installing it.



Hide 28120 4.INSTALL STARTER YOKE ASSEMBLY

a.
A156367C06
1.573,0.771 2.26,0.354 false 1.844,1.063 1.281,1.667 true 2.302,0.25 2.708,0.417 0.406,0.167 10 *b 1.083,1.594 1.406,1.74 0.323,0.146 10 *a
*a Cutout
*b Protrusion


Align the cutout of the starter yoke assembly with the protrusion of the shock absorber.


b.
A288934

Install the starter yoke assembly and starter armature assembly with the 2 through bolts.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


Hide 28150 5.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.
A156359C08
0.865,0.76 0.344,0.354 true 1.271,0.635 0.802,0.146 false 0.156,0.271 0.469,0.427 0.313,0.156 10 false *1 0.615,0.073 0.927,0.229 0.313,0.156 10 false *a
*1 Starter Pinion Drive Lever
*a Hook


Hang the hook of the magnet starter switch assembly to the starter pinion drive lever.


b.
A182596

Install the magnet starter switch assembly to the starter drive housing with the 2 nuts.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


c.
A310451

Connect the lead wire to terminal C with the nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)