Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2013.08–2016.10
RM30M0E _52 Drivetrain _017087 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090604 AUTOMATIC TRANSAXLE SYSTEM U

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

In accordance with the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed Engine speed Min.: 0 rpm
Max.: 16383 rpm
650 to 750 rpm: Idling When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 or varies greatly from the actual engine speed.
N Range Status Judgment for shift lever N position OFF or ON
·

OFF: Shift lever not in P or N

·

ON: Shift lever in P or N


-
Neutral Position SW Signal Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P or N

·

ON: Shift lever in P or N


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Stop Light Switch Stop light switch status OFF or ON
·

OFF: Brake pedal is released

·

ON: Brake pedal is depressed


-
SPD (NT) Input turbine speed Min.: 0 rpm
Max.: 12750 rpm
·

Input turbine speed (NT) equal to engine speed: Lock-up ON (After warming up engine)

·

Input turbine speed (NT) nearly equal to engine speed: Lock-up OFF (Idling in P or N position)

·

0 rpm: Vehicle stopped in R position


-
Shift SW Status (P Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P

·

ON: Shift lever in P


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (R Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in R

·

ON: Shift lever in R


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (2 Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in 2

·

ON: Shift lever in 2


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (L Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in L

·

ON: Shift lever in L


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (N Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in N

·

ON: Shift lever in N


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (N,P Range) Supported Shift lever position P or N support status Supp or Unsupp
·

Supp: Normal

·

Unsupp: Abnormalities in the park/neutral position switch signal


-
Shift SW Status (N,P Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in P or N

·

ON: Shift lever in P or N


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (D Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in D or 3

·

ON: Shift lever in D or 3


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
Shift SW Status (3 Range) Park/neutral position switch status OFF or ON
·

OFF: Shift lever not in 3

·

ON: Shift lever in 3


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect.
A/T Oil Temperature 1 ATF temperature sensor value Min.: -40°C (-40°F)
Max.: 215°C (419°F)
·

Approximately 80°C (176°F): After Stall Test

·

Equal to ambient temperature while engine is cold


If the value is "-40°C (-40°F)" or "150°C (302°F) or more ", ATF temperature sensor circuit is opened or shorted.
Lock Up Lock up status OFF or ON
·

OFF: Lock up not operating

·

ON: Lock up operating


-
ST Solenoid Status Shift solenoid ST status OFF or ON OFF → ON → OFF: Up-shifting and down-shifting between 3rd and 4th gears while driving -
Shift Status Actual gear position 1st, 2nd, 3rd or 4th Same as actual gear -
SLT Solenoid Status Shift solenoid SLT status OFF or ON
·

OFF: Accelerator pedal is depressed

·

ON: Accelerator pedal is released


-
SL Solenoid Status Shift solenoid SL status OFF or ON
·

OFF: Lock Up

·

ON: Except Lock Up


-


ACTIVE TEST


HINT:

Using the GTS to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

In accordance with the display on the GTS, perform the Active Test.

Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the Solenoid (SLT) Operate the shift solenoid SLT and raise the line pressure.
HINT:

OFF: Line pressure up (When the active test of "Activate the Solenoid (SLT)" is performed, ECM commands SLT solenoid to turn off).

ON: No action (normal operation)


ON/OFF [Vehicle Condition]
·

Ignition switch ON

·

Engine idling


Activate the Solenoid (S1) Operate shift solenoid S1 ON/OFF [Vehicle Condition]
·

Ignition switch ON

·

Engine stopped

·

Shift lever in P or N


Activate the Solenoid (S2) Operate shift solenoid S2 ON/OFF [Vehicle Condition]
·

Ignition switch ON

·

Engine stopped

·

Shift lever in P or N


Activate the Lock Up Control shift solenoid SL to set automatic transaxle to lock-up condition. ON/OFF Possible to check SL operation.
[Vehicle Condition]

Vehicle speed: 60 km/h (36 mph) or more, and 4th gear


Activate the Solenoid (SL) Operate shift solenoid SL ON/OFF [Vehicle Condition]
·

Ignition switch ON

·

Engine stopped

·

Shift lever in P or N


Control the Shift Position Operates the shift solenoid valves to allow the gear position to be manually selected [1st - 2nd - 3rd - 4th]
·

Press "→" button: Shift up

·

Press "←" button: Shift down


Possible to check operation of shift solenoid valves.
[Vehicle Condition]

Vehicle speed: 50 km/h (30 mph) or less


Activate the Solenoid (ST) Operate shift solenoid ST ON/OFF [Vehicle Condition]
·

Ignition switch ON

·

Engine idling


HINT:

Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transaxle, which is used in the Hydraulic Test as well. The pressure values in Active Test and Hydraulic Test are different from each other.

Click hereDrivetrain>U340E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>HYDRAULIC TEST