Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2013.08–2016.10
RM30M0E _52 Drivetrain _017087 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090604 AUTOMATIC TRANSAXLE SYSTEM C

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0717  Turbine Speed Sensor Circuit No Signal  


DESCRIPTION

This sensor detects the rotation speed of the input turbine. By comparing the input turbine speed signal (NT) with the speed sensor signal (SPD), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure in response to various conditions, thus performing smooth gear shifting.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0717 Turbine Speed Sensor Circuit No Signal All conditions below are detected for 5 seconds or more (1 trip detection logic).
(a) Gear change is not being performed.
(b) Gear position: 3rd or 4th.
(c) T/M input shaft rpm: Less than 300 rpm.
(d) T/M output shaft rpm: 1000 rpm or more.
(e) Park/neutral position switch (NSW, R and L) is OFF.
(f) Shift solenoid valves, park/neutral position switch and vehicle speed sensor are in normal operation.
·

Wire harness or connector

·

Transmission revolution sensor

·

Automatic transaxle (clutch, brake or gear etc.)

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

The ECM detects the revolving signal from the transmission revolution sensor (input speed). The ECM outputs a gearshift signal by comparing the transmission revolution sensor signal with the speed sensor signal (SPD). While the vehicle is operating in the 3rd or 4th gear position in the shift position of D, if the input shaft speed is less than 300 rpm*1 although the output shaft speed is 1000 rpm*2 or more, the ECM detects the malfunction, illuminates the MIL and stores the DTC.

*1: Pulse is not output or is irregularly output.

*2: The vehicle speed is 50 km/h (31 mph) or more.

WIRING DIAGRAM

C243251E09
0.25,1.792 0.563,1.938 0.313,0.146 10 false B21 0.25,1.948 2.292,2.26 2.042,0.313 10 false Transmission Revolution Sensor 5.583,0.813 5.885,0.969 0.302,0.156 10 false NT+ 5.583,1.479 5.885,1.635 0.302,0.156 10 false NT- 1.74,0.708 1.854,0.865 0.115,0.156 10 false 2 1.74,1.375 1.854,1.531 0.115,0.156 10 false 1 5.26,0.802 5.552,1 0.292,0.198 10 false B31 5.302,0.604 5.563,0.781 0.26,0.177 10 false 35 5.26,1.469 5.583,1.688 0.323,0.219 10 false B31 5.292,1.281 5.542,1.438 0.25,0.156 10 false 27 5.802,2.073 6.177,2.26 0.375,0.188 10 false ECM

PROCEDURE

1.INSPECT TRANSMISSION REVOLUTION SENSOR INSTALLATION
a.
B319222C11
0.49,0.052 0.802,0.208 0.313,0.156 10 *a 2.563,0.052 2.875,0.208 0.313,0.156 10 *b 2.677,1.802 2.99,1.958 0.313,0.156 10 *c
*a Correct
*b Incorrect
*c Clearance


Check the transmission revolution sensor installation.

OK:

The installation bolt is tightened properly and there is no clearance between the sensor and transaxle case.



Result:
Proceed to
OK
NG



OK

2.INSPECT TRANSMISSION REVOLUTION SENSOR

NG

SECURELY INSTALL OR REPLACE TRANSMISSION REVOLUTION SENSOR

2.INSPECT TRANSMISSION REVOLUTION SENSOR
a.
C213110C06
0.146,0.125 0.458,0.281 0.313,0.156 10 *a
*a Component without harness connected
(Transmission Revolution Sensor)


Disconnect the B21 transmission revolution sensor connector from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 560 to 680 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR - ECM)

NG

REPLACE TRANSMISSION REVOLUTION SENSOR

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION REVOLUTION SENSOR - ECM)
a.
C279778C38
1.073,0.583 1.5,0.833 0.427,0.25 0.563,2.063 1.042,2.063 true 0.781,2.771 1.031,2.115 true 1.156,0.635 1.615,0.833 0.458,0.198 10 false B31 0.656,2.802 0.938,3.01 0.281,0.208 10 false NT+ 0.313,1.979 0.583,2.177 0.271,0.198 10 false NT- 0.167,0.146 0.479,0.344 0.313,0.198 10 false *a
*a Rear view of wire harness connector
(to ECM)


Connect the B21 transmission revolution sensor connector to the transaxle.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B31-35 (NT+) - B31-27 (NT-) 20°C (68°F) 560 to 680 Ω
B31-35 (NT+) - Body ground Always 10 kΩ or higher
B31-27 (NT-) - Body ground Always



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR