Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2013.08–2016.10
RM30M0E _52 Drivetrain _017087 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090604 AUTOMATIC TRANSAXLE SYSTEM C

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0787  Shift / Timing Solenoid Low (Shift Solenoid Valve ST)  P0788  Shift / Timing Solenoid High (Shift Solenoid Valve ST)  


DESCRIPTION

The shift solenoid valve ST is switched OFF-ON-OFF in accordance with signals from the ECM when up-shifting and down-shifting between the 3rd and the 4th gears. This reduces the shock of gear shifting between these positions.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0787 Shift / Timing Solenoid Low (Shift Solenoid Valve ST) ECM detects short in solenoid valve ST circuit 4 times when solenoid valve ST is operated (1-trip detection logic).
·

Wire harness or connector

·

Transmission wire

·

Shift solenoid valve ST

·

ECM


Comes on DTC stored
P0788 Shift / Timing Solenoid High (Shift Solenoid Valve ST) ECM detects open in solenoid valve ST circuit 4 times when solenoid valve ST is not operated (1-trip detection logic).
·

Wire harness or connector

·

Transmission wire

·

Shift solenoid valve ST

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

When there is an open or short circuit in the shift solenoid valve circuit, the ECM detects the problem and the MIL comes on.

WIRING DIAGRAM

C243326E29
0.979,1.958 1.292,2.125 0.313,0.167 10 B20 0.979,2.115 2.167,2.292 1.188,0.177 10 Transmission Wire 6.021,2.177 6.375,2.344 0.354,0.167 10 ECM 5.833,1.094 6.031,1.25 0.198,0.156 10 ST 5.458,1.094 5.771,1.313 0.313,0.219 10 B31 5.521,0.896 5.698,1.052 0.177,0.156 10 8 2.292,1.219 2.49,1.375 0.198,0.156 10 ST 2.615,0.99 2.708,1.146 0.094,0.156 10 2 1.146,1.333 2.042,1.646 0.896,0.313 10 Shift Solenoid Valve ST

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE ST)
a.
C229166C33
2,0.927 2.573,0.469 true 2.635,0.396 3.031,0.552 0.396,0.156 10 false ST 0.063,0.063 0.26,0.229 0.198,0.167 10 false *a
*a Component without harness connected
(Transmission Wire)


Disconnect the B20 transmission wire connector from the transaxle.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE ST
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.
C279778C39
1,0.5 1.417,0.75 0.417,0.25 2.25,2.49 1.521,2.01 true 2.302,2.417 2.615,2.615 0.313,0.198 10 false ST 0.094,0.115 0.354,0.302 0.26,0.188 10 false *a 1.094,0.552 1.396,0.76 0.302,0.208 10 false B31
*a Rear view of wire harness connector
(to ECM)


Connect the B20 transmission wire connector to the transaxle.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B31-8 (ST) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE ST
a.
C279783C04
0.698,1.094 0.979,1.448 0.281,0.354 18 false Ω 0.719,3.281 1,3.635 0.281,0.354 18 false B 0.583,2.969 1.042,3.167 0.458,0.198 10 false (+) 0.604,3.635 1.063,3.833 0.458,0.198 10 false (-) 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a
*a Component without harness connected
(Shift Solenoid Valve ST)


Remove the shift solenoid valve ST.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid Connector (ST) - Solenoid Body (ST) 20°C (68°F) 11 to 15 Ω



c.

Connect the positive (+) lead to the terminal of the solenoid connector and the negative (-) lead to the solenoid body to check the solenoid valve operation.

OK:

The solenoid makes operating sounds.



Result:
Proceed to
OK
NG



OK

NG