Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › SHIFT LEVER › 2013.08–2016.10
RM30M0E _52 Drivetrain _017087 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090610 SHIFT LEVER G

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  SHIFT LEVER  INSPECTION  


PROCEDURE

Hide 33560 1.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (w/ Smart Entry and Start System)

a.

Inspect the wire harness and shift lock control ECU.

i.
C286330C02
1.052,2.177 1.521,2.385 true 1.052,2.802 1.51,2.615 true 1.292,2.969 1.646,2.625 true 0.51,1.833 0.823,1.99 0.313,0.156 10 false *a 0.875,2.073 1.083,2.271 0.208,0.198 10 false IG 0.771,2.719 1.083,2.917 0.313,0.198 10 false STP 1.167,2.885 1.354,3.083 0.188,0.198 10 false E
*a Component with harness connected
(Shift Lock Control ECU (Shift Lock Control Unit Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4 (IG) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
8 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V


HINT:

Do not disconnect the shift lock control ECU connector.



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (E) - Body ground Always Below 1 Ω


HINT:

Do not disconnect the shift lock control ECU connector.




b.

Inspect the shift lock solenoid.

i.
C286331

Disconnect the shift lock solenoid connector.


ii.
C197452C24
1.365,1.24 0.854,1.552 true 1.604,1.24 1.375,1.635 true 1.833,1.25 2.031,1.646 true 2.083,1.24 2.583,1.552 true 0.479,1.49 0.854,1.698 0.375,0.208 10 false SLS+ 1.25,1.656 1.646,1.865 0.396,0.208 10 false SLS- 1.969,1.656 2.198,1.865 0.229,0.208 10 false E2 2.635,1.49 2.865,1.698 0.229,0.208 10 false P 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Shift Lock Solenoid (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 112 Ω
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω


·

If the result is not as specified, replace the shift lock control unit assembly.

·

If the shift lock does not operate when the power source of the shift lock control unit assembly is normal and the resistance values of the body ground and the shift lock solenoid are as specified, replace the shift lock control unit assembly.




Hide 33560 2.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (w/o Smart Entry and Start System)

a.

Inspect the wire harness and shift lock control ECU.

i.
C286330C01
1.052,2.177 1.521,2.385 true 1.979,2.396 2.427,2.188 true 1.979,2.604 2.458,2.781 true 1.052,2.802 1.51,2.615 true 1.292,2.969 1.646,2.625 true 0.51,1.833 0.823,1.99 0.313,0.156 10 false *a 0.875,2.073 1.083,2.271 0.208,0.198 10 false IG 0.771,2.719 1.083,2.917 0.313,0.198 10 false STP 2.469,2.094 2.781,2.292 0.313,0.198 10 false ACC 2.49,2.698 2.927,2.896 0.438,0.198 10 false KLS+ 1.167,2.885 1.354,3.083 0.188,0.198 10 false E
*a Component with harness connected
(Shift Lock Control ECU (Shift Lock Control Unit Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
4 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
5 (KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
Ignition switch ACC and shift lever not in P 11 to 14 V
8 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V


HINT:

Do not disconnect the shift lock control ECU connector.



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (E) - Body ground Always Below 1 Ω


HINT:

Do not disconnect the shift lock control ECU connector.




b.

Inspect the shift lock solenoid.

i.
C286331

Disconnect the shift lock solenoid connector.


ii.
C197452C24
1.365,1.24 0.854,1.552 true 1.604,1.24 1.375,1.635 true 1.833,1.25 2.031,1.646 true 2.083,1.24 2.583,1.552 true 0.479,1.49 0.854,1.698 0.375,0.208 10 false SLS+ 1.25,1.656 1.646,1.865 0.396,0.208 10 false SLS- 1.969,1.656 2.198,1.865 0.229,0.208 10 false E2 2.635,1.49 2.865,1.698 0.229,0.208 10 false P 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Shift Lock Solenoid (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 112 Ω
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω


·

If the result is not as specified, replace the shift lock control unit assembly.

·

If the shift lock does not operate when the power source of the shift lock control unit assembly is normal and the resistance values of the body ground and the shift lock solenoid are as specified, replace the shift lock control unit assembly.




Hide 3.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY)

a.

Check the resistance.

i.

Disconnect the transmission control switch connector.


ii.
C193928C24
0.094,0.094 0.271,0.26 0.177,0.167 10 false *a
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Shift lever in 3 or 2 Below 1 Ω
Shift lever not in 3 and 2 10 kΩ or higher


If the result is not as specified, replace the shift lock control unit assembly.