Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT › 2013.08–2016.10
RM30M0E _52 Drivetrain _017087 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090614 AUTOMATIC TRANSAXLE UNIT G

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  INSPECTION  


PROCEDURE

Hide 35633 1.INSPECT FRONT CLUTCH CLUTCH DISC

a.
C286565

Check whether the sliding surface of the front clutch clutch disc, No. 1 clutch plate and the forward clutch flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF WS for at least 15 minutes.




Hide 35677H 2.INSPECT REVERSE CLUTCH DISC

a.
C286566

Check whether the sliding surfaces of the reverse clutch disc, No. 3 clutch plate and the reverse clutch flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF WS for at least 15 minutes.




Hide 35667A 3.INSPECT DIRECT CLUTCH DISC

a.
C286567

Check whether the sliding surface of the direct clutch disc, rear clutch flange and the direct clutch flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF WS for at least 15 minutes.




Hide 34633 4.INSPECT 2ND COAST AND OVERDRIVE BRAKE DISC

a.
C286568

Check whether the sliding surfaces of the 2nd coast and overdrive brake disc, No. 2 2nd coast and overdrive brake flange and the 2nd coast and overdrive brake flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF WS for at least 15 minutes.




Hide 35682 5.INSPECT 2ND BRAKE BRAKE DISC

a.
C286569

Check whether the sliding surfaces of the 2nd brake brake disc, No. 1 2nd brake brake flange and the 2nd brake brake flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF WS for at least 15 minutes.




Hide 35683 6.INSPECT 1ST AND REVERSE BRAKE DISC

a.
C286570

Check whether the sliding surface of the 1st and reverse brake disc, 1st and reverse brake plate and the 1st and reverse brake flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF WS for at least 15 minutes.




Hide 35603A 7.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C287819

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

21.69 mm (0.854 in.)


If the free length is shorter than the standard free length, replace the forward clutch return spring sub-assembly.


Hide 34603B 8.INSPECT OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C287820

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

17.88 mm (0.704 in.)


If the free length is shorter than the standard free length, replace the overdrive brake return spring sub-assembly.


Hide 35604 9.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C282788

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

32.9 mm (1.30 in.)


If the free length is shorter than the standard free length, replace the direct clutch return spring sub-assembly.


Hide 35608L 10.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C287821

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

14.65 mm (0.577 in.)


If the free length is shorter than the standard free length, replace the 2nd brake piston return spring sub-assembly.


Hide 35068 11.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C287820

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

13.96 mm (0.550 in.)


If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring sub-assembly.


Hide 35606A 12.INSPECT DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
C282792

Shake the direct clutch pin and confirm that the check ball is not stuck.


b.

Apply low pressure compressed air to the check ball and check that no air leakage is identified.

If necessary, replace the direct clutch piston sub-assembly.


Hide 35708G 13.INSPECT INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
C282793

Shake the direct clutch pin and confirm that the check ball is not stuck.


b.

Apply low pressure compressed air to the check ball and check that no air leakage is identified.

If necessary, replace the intermediate shaft sub-assembly.