Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT › 2013.08–2016.10
RM30M0E _52 Drivetrain _017087 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090614 AUTOMATIC TRANSAXLE UNIT A

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 35572A 1.REMOVE TRANSMISSION CONTROL SHAFT LEVER

a.
C282395

Remove the nut, washer and the transmission control shaft lever from the manual valve lever shaft.


Hide 84540 2.REMOVE PARK/NEUTRAL POSITION SWITCH

a.
C117104

Using a screwdriver, pry off the tabs of the lock plate.


b.

Remove the lock nut and the lock plate from the park/neutral position switch.


c.
C117106

Remove the 2 bolts and pull out the park/neutral position switch from the transaxle case.


Hide 89413B 3.REMOVE TRANSMISSION REVOLUTION SENSOR

a.
C282680

Remove the bolt and the transmission revolution sensor from the transaxle case.


b.

Remove the O-ring from the transmission revolution sensor.


Hide 32921C 4.REMOVE OIL COOLER TUBE UNION

a.
C282681

Remove the 2 oil cooler tube unions from the transaxle case.


b.

Remove the 2 O-rings from the 2 oil cooler tube unions.


Hide 35104Q 5.REMOVE NO. 1 TRANSAXLE CASE PLUG

a.
C282682

Remove the 4 No. 1 transaxle case plugs from the transaxle housing and the transaxle case.


b.
C282683

Remove the No. 1 transaxle case plug from the transaxle case.


c.

Remove the 5 O-rings from the 5 No. 1 transaxle case plugs.


Hide 35012 6.REMOVE TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

a.
C287808

Remove the transmission breather hose sub-assembly from the breather plug.


Hide 35104B 7.REMOVE BREATHER PLUG

a.
C284798

Using a screwdriver, remove the breather plug from the transaxle case.


b.

Remove the O-ring from the breather plug.


Hide 30500 8.SECURE AUTOMATIC TRANSAXLE ASSEMBLY

a.
C163764C01
1.948,1.802 1.625,1.927 1.625,1.927 1.292,1.802 false 1.573,1.948 1.885,2.146 0.313,0.198 10 false *a
*a Wooden Block


Place the automatic transaxle assembly on wooden blocks.


Hide 35106D 9.REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C293686

Using a 10 mm hexagon socket wrench, remove the drain plug sub-assembly and the gasket from the automatic transaxle oil pan sub-assembly.


b.
C282685

Remove the 19 bolts, automatic transaxle oil pan sub-assembly and the automatic transaxle oil pan gasket from the transaxle case.


Hide 35394 10.REMOVE TRANSMISSION OIL CLEANER MAGNET

a.
C282686

Remove the 2 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.


b.
C283249

Examine the particles in the automatic transaxle oil pan sub-assembly.

i.

Collect any steel chips using the removed transmission oil cleaner magnets.

Carefully inspect the foreign matter and particles in the automatic transaxle oil pan sub-assembly and on the transmission oil cleaner magnets to see the type of wear which might be found in the automatic transaxle assembly.

Steel (magnetic): bearing, gear and clutch plate wear

Brass (non-magnetic): bushing wear



Hide 35330 11.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

a.
C282687

Remove the 3 bolts and the valve body oil strainer assembly from the transmission valve body assembly.


b.
C282688

Remove the oil strainer O-ring from the valve body oil strainer assembly.


Hide 35410 12.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
C282689

Remove the bolt and the temperature sensor clamp and separate the transmission wire from the transmission valve body assembly.


b.

Disconnect the 5 connectors from the transmission valve body assembly.


c.
C282690C01
2.208,0.792 2.802,0.573 true 2.229,1.219 2.792,1.427 true 2.844,0.458 3.156,0.656 0.313,0.198 10 false *1 2.823,1.333 3.135,1.531 0.313,0.198 10 false *2
*1 Manual Detent Spring Sub-assembly
*2 Manual Detent Spring Cover


Remove the 2 bolts, manual detent spring cover and the manual detent spring sub-assembly from the transmission valve body assembly.


d.
C282691

Remove the 13 bolts and the transmission valve body assembly from the transaxle case.


Hide 82125J 13.REMOVE TRANSMISSION WIRE

a.
C282692

Remove the bolt and the transmission wire from the transaxle case.


b.
C282693

Remove the O-ring from the transmission wire.


Hide 35145C 14.REMOVE TRANSAXLE CASE GASKET

a.
C282695

Remove the transaxle case gasket from the transaxle case.


Hide 35149B 15.REMOVE TRANSAXLE CASE 2ND BRAKE GASKET

a.
C282694

Remove the transaxle case 2nd brake gasket from the transaxle case.


Hide 35159 16.REMOVE BRAKE DRUM GASKET

a.
C282696

Remove the brake drum gasket from the transaxle case.


Hide 35251 17.REMOVE CHECK BALL BODY

a.
C282697

Remove the check ball body and the check ball body compression spring from the transaxle case.


Hide 35423 18.REMOVE B-2 ACCUMULATOR PISTON

a.
C282698

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-2 accumulator piston and the B-2 accumulator piston compression spring.

NOTICE:
·

Blowing the air may cause the B-2 accumulator piston to jump out. When removing the B-2 accumulator piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




b.
C282699

Remove the 2 B-2 accumulator piston O-rings from the B-2 accumulator piston.


Hide 35426D 19.REMOVE C-3 ACCUMULATOR PISTON

a.
C282700

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-3 accumulator piston and the C-3 accumulator piston compression spring.

NOTICE:
·

Blowing the air may cause the C-3 accumulator piston to jump out. When removing the C-3 accumulator piston, hold it with your hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




b.
C282701

Remove the 2 C-3 accumulator piston O-rings from the C-3 accumulator piston.


Hide 35425A 20.REMOVE C-2 ACCUMULATOR PISTON

a.
C282702

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the C-2 accumulator piston and the C-2 accumulator piston compression spring.

NOTICE:
·

Blowing the air may cause the C-2 accumulator piston to jump out. When removing the C-2 accumulator piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




b.
C282703

Remove the 2 C-2 accumulator piston O-rings from the C-2 accumulator piston.


Hide 35111C 21.REMOVE TRANSAXLE HOUSING

a.
C282704

Remove the 14 bolts.


b.

Tap around the circumference of the transaxle housing with a plastic hammer to remove the transaxle housing from the transaxle case.

NOTICE:

The differential gear assembly may be accidentally removed when the transaxle housing is removed.



c.
C282708

Remove the 2 O-rings from the transaxle case.


Hide 22.INSPECT INPUT SHAFT END PLAY

a.
C282705

Using a dial indicator, measure the input shaft end play.

Standard end play:

0.374 to 1.292 mm (0.0148 to 0.0508 in.)


If the end play is not as specified, replace the stator shaft thrust needle roller bearing and the forward clutch hub thrust needle roller bearing.


Hide 23.REMOVE OIL PUMP ASSEMBLY

a.
C282706

Remove the 7 bolts and the oil pump assembly from the transaxle case.


Hide 24.REMOVE DIFFERENTIAL GEAR ASSEMBLY

a.
C282707

Remove the differential gear assembly from the transaxle case.


Hide 35701 25.REMOVE INPUT SHAFT SUB-ASSEMBLY

a.
C282709

Remove the input shaft sub-assembly from the transaxle case.


Hide 35370A 26.REMOVE STATOR SHAFT THRUST NEEDLE ROLLER BEARING

a.
C282710

Remove the stator shaft thrust needle roller bearing from the input shaft sub-assembly.


Hide 35633 27.REMOVE FRONT CLUTCH CLUTCH DISC

a.
C282711

Using a screwdriver, remove the forward clutch flange hole snap ring from the input shaft sub-assembly.


b.

Remove the forward clutch flange, 4 front clutch clutch discs and the 4 No. 1 clutch plates from the input shaft sub-assembly.


Hide 35603A 28.REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C282712E03
1,0.635 1.583,0.958 false 0.698,0.542 1.156,0.74 0.458,0.198 10 false SST

Using SST on the No. 1 clutch balancer, compress the forward clutch return spring sub-assembly with a press.

SST
09320-89010  

NOTICE:

Do not compress the return spring excessively.



b.

Using a snap ring expander, remove the clutch balancer snap ring from the input shaft sub-assembly.


c.
C282837

Remove the No. 1 clutch balancer and the forward clutch return spring sub-assembly from the input shaft sub-assembly.


Hide 35612B 29.REMOVE FORWARD CLUTCH PISTON

a.
C287809

Place the input shaft sub-assembly onto the oil pump assembly.


b.

Holding the forward clutch piston by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil pump assembly to remove the forward clutch piston from the input shaft sub-assembly.

HINT:

When the piston cannot be removed due to being slanted, either blow the air again with the protruding side pushed or remove the piston using needle-nose pliers with their tips wrapped in protective tape.



Hide 35612C 30.REMOVE FORWARD CLUTCH PISTON O-RING

a.
C282715

Remove the forward clutch piston O-ring from the forward clutch piston.


Hide 35712A 31.REMOVE INPUT SHAFT OIL SEAL RING

a.
C287810

Remove the input shaft oil seal ring from the input shaft sub-assembly.


Hide 35061C 32.REMOVE FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING

a.
C282717

Remove the forward clutch hub thrust needle roller bearing from the forward clutch hub sub-assembly.


Hide 35061 33.REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

a.
C282719

Remove the forward clutch hub sub-assembly from the transaxle case.


Hide 34.INSPECT INTERMEDIATE SHAFT END PLAY

a.
C282718

Using a dial indicator, measure the intermediate shaft end play.

Standard end play:

0.204 to 0.966 mm (0.00804 to 0.0380 in.)


If the end play is not as specified, select and replace the rear clutch drum thrust needle roller bearing.

HINT:

There are 2 different thicknesses of thrust needle roller bearings available.



Hide 35102 35.REMOVE TRANSAXLE REAR COVER SUB-ASSEMBLY

a.
C287818

Remove the 11 bolts.


b.

Tap around the circumference of the transaxle rear cover sub-assembly with a plastic hammer to remove the transaxle rear cover sub-assembly from the transaxle case.


c.
C282728

Remove the 4 O-rings from the transaxle case.


Hide 35102B 36.REMOVE TRANSAXLE REAR COVER PLUG

a.
C282721

Remove the 4 transaxle rear cover plugs from the transaxle rear cover sub-assembly.


b.

Remove the 4 O-rings from the 4 transaxle rear cover plugs.


Hide 34603B 37.REMOVE OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C287811E01
1.781,2.24 2.146,2.063 false 2.01,0.854 2.635,0.531 true 2.708,0.438 3.167,0.635 0.458,0.198 10 false SST 2.198,1.958 2.656,2.156 0.458,0.198 10 false SST

Using SST, a press and a screwdriver, remove the overdrive brake return spring hole snap ring from the transaxle rear cover sub-assembly.

SST
09387-00070  

NOTICE:

Stop the press when the overdrive brake return spring sub-assembly is lowered to 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove, to prevent the overdrive brake return spring sub-assembly from being deformed.



b.
C287812

Remove the overdrive brake return spring sub-assembly from the transaxle rear cover sub-assembly.


Hide 34622B 38.REMOVE 2ND COAST AND OVERDRIVE BRAKE PISTON

a.
C282724

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle rear cover sub-assembly to remove the 2nd coast and overdrive brake piston from the transaxle rear cover sub-assembly.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 34622C 39.REMOVE 2ND COAST AND OVERDRIVE O-RING

a.
C282725

Remove the 2 2nd coast and overdrive O-rings from the 2nd coast and overdrive brake piston.


Hide 35617G 40.REMOVE CLUTCH DRUM OIL SEAL RING

a.
C282726

Remove the 3 clutch drum oil seal rings from the transaxle rear cover sub-assembly.


Hide 35102D 41.REMOVE TRANSAXLE REAR COVER NEEDLE ROLLER BEARING

a.
C282727C01
0.365,1.25 0.844,0.917 true 2.365,1.094 2.479,1.021 false 0.479,0.24 0.792,0.438 0.313,0.198 10 false *a 1.667,0.865 1.979,1.063 0.313,0.198 10 false *b 0.063,1.167 0.521,1.365 0.458,0.198 10 false SST 2.073,1.021 2.531,1.219 0.458,0.198 10 false SST
*a Hold
*b Turn


Using SST, remove the transaxle rear cover needle roller bearing from the transaxle rear cover sub-assembly.

SST
09387-00041  (09387-01021, 09387-01030, 09387-01041)


Hide 35651B 42.REMOVE REAR CLUTCH DRUM THRUST NEEDLE ROLLER BEARING

a.
C282729

Using a magnet hand, remove the rear clutch drum thrust needle roller bearing from the intermediate shaft sub-assembly.


Hide 35708G 43.REMOVE INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
C282730

Remove the intermediate shaft sub-assembly from the transaxle case.


Hide 35677H 44.REMOVE REVERSE CLUTCH DISC

a.
C282731

Using a screwdriver, remove the reverse clutch flange hole snap ring from the intermediate shaft sub-assembly.


b.

Remove the reverse clutch flange, 2 reverse clutch discs and the 2 No. 3 clutch plates from the intermediate shaft sub-assembly.


Hide 35667A 45.REMOVE DIRECT CLUTCH DISC

a.
C282732

Using a screwdriver, remove the direct clutch flange hole snap ring from the intermediate shaft sub-assembly.


b.

Remove the direct clutch flange, 3 direct clutch discs and the 3 rear clutch flanges from the intermediate shaft sub-assembly.


Hide 35604 46.REMOVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C282733E01
2.552,0.875 2.823,0.875 false 2.875,0.802 3.333,1 0.458,0.198 10 false SST

Using SST, a press and a snap ring expander, remove the direct clutch piston shaft snap ring from the direct clutch drum sub-assembly.

SST
09387-00020  


b.

Remove the direct clutch return spring sub-assembly from the intermediate shaft sub-assembly.


Hide 35606A 47.REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
C282734

Install the intermediate shaft sub-assembly onto the transaxle rear cover sub-assembly.


b.

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole shown in the illustration and remove the direct clutch piston sub-assembly from the intermediate shaft sub-assembly.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35606C 48.REMOVE DIRECT CLUTCH PISTON O-RING

a.
C282736

Remove the 2 direct clutch piston O-rings from the direct clutch piston sub-assembly.


Hide 35605A 49.REMOVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

a.
C282735C01
2.781,0.969 2.781,0.573 true 2.688,0.302 2.792,0.406 false 2.542,0.198 2.854,0.354 0.313,0.156 10 false *a 2.729,0.979 3.042,1.135 0.313,0.156 10 false *b
*a Cutout
*b Matchmark


Install the intermediate shaft sub-assembly onto the transaxle rear cover sub-assembly.


b.

Put a matchmark on the direct clutch drum sub-assembly in the same position as the cutout of the intermediate shaft sub-assembly.


c.

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole shown in the illustration and remove the direct clutch drum sub-assembly from the intermediate shaft sub-assembly.

NOTICE:
·

Blowing the air may cause the drum to jump out. When removing the drum, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35605D 50.REMOVE DIRECT CLUTCH DRUM O-RING

a.
C282737

Remove the direct clutch drum O-ring from the direct clutch drum sub-assembly.


Hide 34633 51.REMOVE 2ND COAST AND OVERDRIVE BRAKE DISC

a.
C282738

Remove the 2nd coast and overdrive brake flange, 2 2nd coast and overdrive brake discs and the 2 No. 2 2nd coast and overdrive brake flanges from the transaxle case.


Hide 35605B 52.REMOVE THRUST NEEDLE ROLLER BEARING

a.
C282739

Using a magnet hand, remove the C-2 hub thrust bearing race, thrust needle roller bearing and the No. 3 thrust bearing race from the direct clutch hub.


Hide 35654B 53.REMOVE DIRECT CLUTCH HUB

a.
C282740

Remove the direct clutch hub from the transaxle case.


Hide 35730C 54.REMOVE REAR NO. 2 PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING

a.
C282741

Using a magnet hand, remove the rear No. 2 planetary sun gear thrust needle roller bearing from the rear planetary sun gear assembly.


Hide 35730 55.REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

a.
C282742

Remove the rear planetary sun gear assembly and the 1-way clutch assembly from the transaxle case.


Hide 35730B 56.REMOVE REAR PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING

a.
C282743

Remove the rear planetary sun gear thrust needle roller bearing and the No. 1 planetary carrier thrust washer from the rear planetary sun gear assembly.


Hide 35790A 57.INSPECT 1-WAY CLUTCH ASSEMBLY

a.
C282745C01
0,0 0,0 false
V100135

Lock
V100136

Free


Hold the rear planetary sun gear assembly and turn the 1-way clutch assembly.


b.

Check that the 1-way clutch assembly turns freely counterclockwise and locks when turned clockwise.

If the 1-way clutch assembly does not operate normally, replace it.


Hide 35790A 58.REMOVE 1-WAY CLUTCH ASSEMBLY

a.
C282746

Remove the 1-way clutch assembly and the No. 2 planetary carrier thrust washer from the rear planetary sun gear assembly.


Hide 34625E 59.REMOVE 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING

a.
C282747

Using a screwdriver, remove the 2nd coast and overdrive brake flange hole snap ring from the transaxle case.


Hide 35682 60.REMOVE 2ND BRAKE BRAKE DISC

a.
C282748

Using a screwdriver, remove the 2nd brake hole snap ring from the transaxle case.


b.

Remove the 2nd brake brake flange, 3 2nd brake brake discs and the 3 No. 1 2nd brake brake flanges from the transaxle case.


Hide 35626D 61.REMOVE 2ND BRAKE PISTON SLEEVE

a.
C282749

Remove the 2nd brake piston sleeve from the transaxle case.


Hide 35792C 62.INSPECT NO. 2 1-WAY CLUTCH

a.
C282750C01
0,0 0,0 false
V100135

Lock
V100136

Free


Check that the rear planetary gear assembly turns freely counterclockwise and locks when turned clockwise.

If the No. 2 1-way clutch does not operate normally, replace it.


Hide 35760 63.REMOVE REAR PLANETARY GEAR ASSEMBLY

a.
C282751

Using a screwdriver, remove the No. 2 1-way clutch hole snap ring from the transaxle case.


b.

Remove the rear planetary gear assembly, 2nd brake piston and the No. 2 1-way clutch from the transaxle case.


Hide 35720K 64.REMOVE REAR PLANETARY GEAR THRUST NEEDLE ROLLER BEARING

a.
C282752

Remove the thrust bearing race, rear planetary gear thrust needle roller bearing and the No. 2 thrust bearing race from the rear planetary gear assembly.


Hide 35792C 65.REMOVE NO. 2 1-WAY CLUTCH

a.
C282753

Remove the No. 2 1-way clutch and the 2nd brake piston from the rear planetary gear assembly.


Hide 34365A 66.REMOVE OUTER RACE RETAINER

a.
C282754

Remove the outer race retainer from the No. 2 1-way clutch.


Hide 35608L 67.REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C287813E01
2.406,0.573 2.781,0.438 false 2.854,0.333 3.313,0.531 0.458,0.198 10 false SST

Using SST, a press and a screwdriver, remove the 2nd brake piston return spring snap ring from the 2nd brake cylinder.

SST
09387-00060  


b.
C282756

Remove the 2nd brake piston return spring sub-assembly from the 2nd brake cylinder.


Hide 35624E 68.REMOVE 2ND BRAKE PISTON

a.
C282757

Hold the 2nd brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the 2nd brake cylinder to remove the 2nd brake piston from the 2nd brake cylinder.


Hide 35664D 69.REMOVE 2ND BRAKE CYLINDER O-RING

a.
C282758

Remove the 2 2nd brake cylinder O-rings from the 2nd brake cylinder.


Hide 35714D 70.REMOVE FRONT PLANETARY SUN GEAR

a.
C282759

Remove the front planetary sun gear and the front planetary gear thrust needle roller bearing from the planetary gear assembly.


Hide 35683 71.REMOVE 1ST AND REVERSE BRAKE DISC

a.
C287814

Using a screwdriver, remove the 1st and reverse plate snap ring from the transaxle case.


b.

Remove the 1st and reverse brake flange, 4 1st and reverse brake discs and the 4 1st and reverse brake plates from the transaxle case.


Hide 35782H 72.REMOVE COUNTER DRIVE GEAR NUT

a.
C282761

Fix the counter drive gear with the parking lock pawl.


b.
C282762E02
0.615,0.417 1.76,1.01 true 0.302,0.323 0.76,0.521 0.458,0.198 10 false SST

Using SST and a hammer, release the counter drive gear lock nut lock washer.

SST
09930-00010  


c.
C282763E02
1.365,1.198 0.448,0.604 true 0.146,0.51 0.604,0.708 0.458,0.198 10 false SST

Using SST, remove the counter drive gear nut and the counter drive gear lock nut lock washer.

SST
09387-00121  


Hide 35720G 73.REMOVE PLANETARY GEAR ASSEMBLY

a.
C283219E02
2,1.615 2.771,1.333 2.771,1.333 1.802,1.146 false 2.813,1.25 3.271,1.448 0.458,0.198 10 false SST

Using SST and a press, remove the planetary gear assembly from the transaxle case.

SST
09950-60010  (09951-00400, 09951-00320, 09952-06010)
09950-70010  (09951-07100)


Hide 35782C 74.REMOVE COUNTER DRIVE GEAR

a.
C283220

Install the 2 bolts to the counter drive gear.

Recommended service bolt:
Diameter:

10 mm

Pitch:

1.25 mm

Length:

40 to 80 mm (1.58 to 3.14 in.)



b.

Rotate the 2 bolts and remove the counter drive gear from the transaxle case.


Hide 35068 75.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C282764E02
0.396,1.802 1.427,1.479 true 0.104,1.719 0.563,1.917 0.458,0.198 10 false SST

Using SST, a press and a screwdriver, remove the brake flange hole snap ring from the transaxle case.

SST
09387-00070  


b.

Remove the 1st and reverse brake return spring sub-assembly from the transaxle case.


Hide 35623P 76.REMOVE NO. 2 1ST AND REVERSE BRAKE PISTON

a.
C282765

Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the No. 2 1st and reverse brake piston from the transaxle case.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35623Q 77.REMOVE NO. 2 1ST AND REVERSE BRAKE PISTON O-RING

a.
C282766

Remove the 2 No. 2 1st and reverse brake piston O-rings from the No. 2 1st and reverse brake piston.


Hide 35595 78.REMOVE PARKING LOCK PAWL BRACKET

a.
C282767

Remove the 3 bolts, parking lock cam guide and the parking lock pawl bracket from the transaxle case.


Hide 35506J 79.REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING

a.
C282768

Remove the manual valve lever shaft retainer spring from the manual valve lever shaft.


Hide 35505 80.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

a.
C282769

Using a screwdriver, release and remove the manual valve lever spacer.


b.
C282770

Using a 3 mm pin punch and a hammer, drive out the manual valve lever shaft slotted spring pin.


c.

Remove the manual valve lever sub-assembly from the manual valve lever shaft.


Hide 35501 81.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

a.
C282771

Remove the parking lock rod sub-assembly from the manual valve lever sub-assembly.


Hide 35561 82.REMOVE MANUAL VALVE LEVER SHAFT

a.
C287815

Remove the manual valve lever shaft from the transaxle case.


Hide 35557 83.REMOVE PARKING LOCK PAWL

a.
C282773

Remove the parking lock pawl shaft, parking lock pawl torsion spring and the parking lock pawl from the transaxle case.


Hide 41205 84.REMOVE DIFFERENTIAL DRIVE PINION SUB-ASSEMBLY

a.
C282774

Remove the differential drive pinion sub-assembly and the drive pinion thrust bearing LH from the transaxle case.


Hide 41211E 85.REMOVE DIFFERENTIAL DRIVE PINION PLUG

a.
C282775

Using a brass bar and a hammer, remove the differential drive pinion plug from the differential drive pinion sub-assembly.


Hide 86.REMOVE COUNTER DRIVEN GEAR

a.
C283105N01
1.771,0.552 2.406,0.75 2.406,0.75 1.823,1.083 true 2.458,0.667 2.917,0.865 0.458,0.198 10 false SST

Using SST and a press, remove the counter driven gear from the differential drive pinion sub-assembly.

SST
09950-60010  (09951-00350)
09950-70010  (09951-07150)


Hide 33326E 87.REMOVE BEARING LOCK PLATE

a.
C282776

Remove the bolt and the bearing lock plate from the transaxle housing.


Hide 35882D 88.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C282777

Remove the differential gear lube apply tube from the transaxle housing.


Hide 41211A 89.REMOVE FRONT DRIVE PINION FRONT CYLINDRICAL ROLLER BEARING

a.
C283424C01
0.656,0.271 1.052,0.563 false 0.365,0.167 0.823,0.365 0.458,0.198 10 false SST 0.125,1.167 0.438,1.365 0.313,0.198 10 false *a 1.781,0.552 1.969,0.74 0.188,0.188 10 true *b
*a Hold
*b Turn


Using SST, remove the front drive pinion front cylindrical roller bearing from the transaxle housing.

SST
09308-10010  


b.

Remove the drive pinion thrust bearing RH from the transaxle housing.


Hide 41211B 90.REMOVE FRONT DRIVE PINION REAR CYLINDRICAL ROLLER BEARING

a.
C283423C01
1.448,1.271 1.813,0.771 true 2.76,1.698 2.865,1.781 true 2.365,0.302 2.677,0.5 0.313,0.198 10 false *a 0.083,1.135 0.396,1.333 0.313,0.198 10 false *b 1.865,0.677 2.229,0.875 0.365,0.198 10 false SST 2.885,1.688 3.198,1.885 0.313,0.198 10 false *1
*1 No. 1 Transaxle Case Plate
*a Hold
*b Turn


Using SST, remove the front drive pinion rear cylindrical roller bearing from the transaxle case.

SST
09612-65014  (09612-01040, 09612-01050)


b.

Remove the No. 1 transaxle case plate from the transaxle case.


Hide 35782E 91.REMOVE COUNTER DRIVE GEAR BEARING

a.
C282780E02
0.531,0.26 0.938,0.396 false 0.24,0.167 0.698,0.365 0.458,0.198 10 false SST

Remove the 2 counter drive gear bearing inner races and 2 angular balls from the transaxle case.


b.

Using SST, remove the counter drive gear bearing outer race from the transaxle case.

SST
09308-00010  


c.
C282781E01
1.542,0.708 2.854,0.281 true 2.896,0.177 3.229,0.385 0.333,0.208 10 true SST

Using SST, remove the counter drive gear bearing outer race from the transaxle case.

SST
09308-00010  


Hide 35782D 92.REMOVE COUNTER DRIVE GEAR HOLE SNAP RING

a.
C282782

Using a screwdriver, remove the counter drive gear hole snap ring from the transaxle case.


Hide 35506F 93.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C282783C01
0.729,0.594 1.656,1.156 true 0.573,0.49 0.885,0.646 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, pry out the manual valve lever shaft oil seal from the transaxle case.


Hide 43420H 94.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C282785E01
1.396,1.271 0.573,0.354 0.573,0.354 1.469,0.698 true 0.26,0.271 0.719,0.469 0.458,0.198 10 false SST

Using SST and a hammer, remove the front drive shaft oil seal LH from the transaxle case.

SST
09950-60010  (09951-00550)
09950-70010  (09951-07100)


Hide 43410M 95.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C282784E01
1.479,1.615 0.5,0.438 0.5,0.438 1.552,0.969 true 0.188,0.344 0.646,0.542 0.458,0.198 10 false SST

Using SST and a hammer, remove the front drive shaft oil seal RH from the transaxle housing.

SST
09950-60010  (09951-00530)
09950-70010  (09951-07100)