Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT › 2013.08–2016.10
RM30M0E _52 Drivetrain _017087 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090614 AUTOMATIC TRANSAXLE UNIT A

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

HINT:

Check bearing position and installation direction.


C283221

Hide 2.INSPECT DIFFERENTIAL CASE TAPERED ROLLER BEARING PRELOAD

a.

Coat the differential gear assembly and the front differential case tapered roller bearing with Toyota Genuine ATF WS and install them to the transaxle case.


b.
C282704E01
0.5,1.813 0.656,2.01 0.156,0.198 10 false A 1.073,1.99 1.229,2.177 0.156,0.188 10 false A 1.396,1.948 1.552,2.146 0.156,0.198 10 false A 0.208,1.271 0.365,1.469 0.156,0.198 10 false A 0.302,0.604 0.458,0.802 0.156,0.198 10 false A 2.688,0.354 2.844,0.552 0.156,0.198 10 false A 2.917,0.958 3.073,1.156 0.156,0.198 10 false A 0.677,0.219 0.833,0.417 0.156,0.198 10 false A 2.073,0.073 2.229,0.271 0.156,0.198 10 false A 1.667,0.031 1.823,0.229 0.156,0.198 10 false A 1.104,0.073 1.26,0.271 0.156,0.198 10 false A 1.667,1.833 1.823,2.031 0.156,0.198 10 false B 2.313,1.823 2.469,2.021 0.156,0.198 10 false B 2.74,1.542 2.896,1.74 0.156,0.198 10 false B

Install the transaxle housing to the transaxle case with the 14 bolts.

Torque:
Bolt A : 29.4 N*m (300 kgf*cm, 22 ft.*lbf)
Bolt B : 22.1 N*m (225 kgf*cm, 16 ft.*lbf)


c.
C282795E01
1.917,0.427 2.521,0.729 true 1.615,0.333 1.969,0.5 0.354,0.167 10 false SST

Using SST and a torque wrench, measure the preload of the differential case tapered roller bearing.

SST
09564-32011  

Standard preload (at Starting):
New bearing:

0.98 to 1.57 N*m (10.0 to 16.0 kgf*cm, 8.7 to 13.8 in.*lbf)

Used bearing:

0.49 to 0.78 N*m (5.0 to 7.9 kgf*cm, 4.4 to 6.9 in.*lbf)


If the preload is not within the specifications, remove the front differential case rear tapered roller bearing from the transaxle case.

Select a new front differential case rear shim in accordance with the following table.

Front Differential Case Rear Shim Thickness:
Part No. Mark Thickness
mm (in.)
Part No. Mark Thickness
mm (in.)
90564-49001 01 1.90 (0.0748) 90564-49011 11 2.40 (0.0945)
90564-49002 02 1.95 (0.0768) 90564-49012 12 2.45 (0.0965)
90564-49003 03 2.00 (0.0787) 90564-49013 13 2.50 (0.0984)
90564-49004 04 2.05 (0.0807) 90564-49014 14 2.55 (0.1004)
90564-49005 05 2.10 (0.0827) 90564-49015 15 2.60 (0.1024)
90564-49006 06 2.15 (0.0846) 90564-49016 16 2.65 (0.1043)
90564-49007 07 2.20 (0.0866) 90564-49017 17 2.70 (0.1063)
90564-49008 08 2.25 (0.0886) 90564-49018 18 2.75 (0.1083)
90564-49009 09 2.30 (0.0906) 90564-49019 19 2.80 (0.1102)
90564-49010 10 2.35 (0.0925) - - -



Hide 43420H 3.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C282796E01
1.74,1.458 2.615,0.99 2.615,0.99 1.583,1.25 true 2.667,0.906 3.125,1.104 0.458,0.198 10 false SST

Using SST and a hammer, tap in a new front drive shaft oil seal LH to the transaxle case.

SST
09710-20011  (09710-06071)
09950-70010  (09951-07100)

Standard depth:

5.4 to 6.4 mm (0.213 to 0.251 in.)



b.

Coat the lip of the front drive shaft oil seal LH with MP grease.


Hide 43410M 4.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C282797E02
2.583,1.198 2.917,1.125 true 2.583,1.448 2.927,1.125 2.927,1.125 2.448,0.771 true 2.969,1.031 3.302,1.25 0.333,0.219 10 false SST

Using SST and a hammer, tap in a new front drive shaft oil seal RH to the transaxle housing.

SST
09630-24014  (09620-24051)
09950-60010  (09951-00410, 09951-00530, 09952-06010)
09950-70010  (09951-07100)

Standard depth:

1.5 to 2.5 mm (0.0591 to 0.0984 in.)



b.

Coat the lip of the front drive shaft oil seal RH with MP grease.


Hide 35506F 5.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C282798E01
1.51,1.063 0.479,0.583 0.479,0.583 0.885,1.177 true 0.188,0.479 0.646,0.677 0.458,0.198 10 false SST

Using SST and a hammer, install a new manual valve lever shaft oil seal to the transaxle case.

SST
09950-60010  (09951-00220)
09950-70010  (09951-07100)

Standard depth:

-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)



b.

Coat the lip of the manual valve lever shaft oil seal with MP grease.


Hide 35782D 6.INSTALL COUNTER DRIVE GEAR HOLE SNAP RING

a.
C282782

Using a screwdriver, install the counter drive gear hole snap ring to the transaxle case.


Hide 35782E 7.INSTALL COUNTER DRIVE GEAR BEARING

a.
C287816E01
1.438,1.25 1.479,0.938 1.479,0.938 1.24,1.01 true 1.49,0.76 1.802,0.927 0.313,0.167 10 true SST

Using SST and a hammer, install the counter drive gear bearing outer race to the transaxle case.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)


b.
C157441N01
1.052,0.958 1.24,0.938 1.24,0.938 1.125,1.302 true 1.281,0.833 1.583,1.01 0.302,0.177 10 true SST

Using SST and a hammer, install the counter drive gear bearing outer race to the transaxle case.

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)


c.

Install the 2 counter drive gear bearing inner races and 2 angular balls to the transaxle case.


Hide 41211B 8.INSTALL FRONT DRIVE PINION REAR CYLINDRICAL ROLLER BEARING

a.
C125250C01
2.427,0.792 2.125,0.969 false 0.688,0.26 0.865,0.438 0.177,0.177 10 false *a 0.719,1.698 0.906,1.875 0.188,0.177 10 false *b 2.458,0.698 2.823,1.031 0.365,0.333 10 false *1
*1 No. 1 Transaxle Case Plate
*a Bearing Side
*b Transaxle Case Side


Install the No. 1 transaxle case plate to the transaxle case.


b.
C157438N01
0.958,1.208 1.552,1.448 1.552,1.448 1.063,1.365 true 1.594,1.385 2.052,1.583 0.458,0.198 10 false SST

Using SST and a hammer, install a new front drive pinion rear cylindrical roller bearing to the transaxle case.

SST
09950-60010  (09951-00610)
09950-70010  (09951-07150)


Hide 41211A 9.INSTALL FRONT DRIVE PINION FRONT CYLINDRICAL ROLLER BEARING

a.
C157439N01
1.417,0.844 1.615,0.708 1.615,0.708 1.5,1.177 true 1.667,0.604 2.125,0.802 0.458,0.198 10 false SST

Coat the drive pinion thrust bearing RH with Toyota Genuine ATF WS, and install it to the transaxle housing.


b.

Using SST and a press, install a new front drive pinion front cylindrical roller bearing to the transaxle housing.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07150)


Hide 35882D 10.INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C282777

Install the differential gear lube apply tube to the transaxle housing.


Hide 33326E 11.INSTALL BEARING LOCK PLATE

a.
C282776

Install the bearing lock plate to the transaxle housing with the bolt.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 12.INSTALL COUNTER DRIVEN GEAR

a.
C283108N01
1.75,0.448 2.219,0.583 2.219,0.583 1.802,0.76 false 2.26,0.51 2.719,0.708 0.458,0.198 10 false SST

Using SST and a press, install the counter driven gear to the differential drive pinion sub-assembly.

SST
09950-60010  (09951-00350)
09950-70010  (09951-07150)

NOTICE:
·

When replacing the counter driven gear, replace the counter drive gear in the transaxle case as well.

·

Press in the differential drive pinion sub-assembly until it comes into contact with the counter driven gear.




Hide 41211E 13.INSTALL DIFFERENTIAL DRIVE PINION PLUG

a.
C282803E01
1.844,0.573 2.448,0.688 false 2.49,0.625 2.948,0.823 0.458,0.198 10 false SST

Using SST and a plastic hammer, install a new differential drive pinion plug to the differential drive pinion sub-assembly.

SST
09221-25026  (09221-00071)

Standard depth:

2.5 to 3.5 mm (0.0985 to 0.137 in.)



Hide 41205 14.INSTALL DIFFERENTIAL DRIVE PINION SUB-ASSEMBLY

a.
C282804

Coat the drive pinion thrust bearing LH with Toyota Genuine ATF WS, and install it to the transaxle case.


b.

Install the differential drive pinion sub-assembly to the transaxle case.


Hide 35557 15.INSTALL PARKING LOCK PAWL

a.
C282773

Install the parking lock pawl and the parking lock pawl shaft torsion spring to the transaxle case with the parking lock pawl shaft.

NOTICE:

Check that the parking lock pawl moves smoothly.



Hide 35561 16.INSTALL MANUAL VALVE LEVER SHAFT

a.
C287815

Install the manual valve lever shaft to the transaxle case.

NOTICE:

Do not damage the oil seal lip.



Hide 35501 17.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

a.
C282771

Install the parking lock rod sub-assembly to the manual valve lever sub-assembly.


Hide 35505 18.INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

a.
C282770

Install the manual valve lever sub-assembly and a new manual valve lever spacer to the manual valve lever shaft.


b.

Using a 3 mm pin punch and a hammer, drive in the manual valve lever shaft spring pin.


c.
C282805

Turn the manual valve lever spacer and the manual valve lever shaft to align the small hole for locating the staking position on the manual valve lever spacer with the staking position mark on the manual valve lever shaft.


d.

Using a punch, stake the manual valve lever spacer through the small hole.


e.

Check that the manual valve lever shaft spacer does not turn.


Hide 35506J 19.INSTALL MANUAL VALVE LEVER SHAFT RETAINER SPRING

a.
C282768

Install the manual valve lever shaft retainer spring to the manual valve lever shaft.


Hide 35595 20.INSTALL PARKING LOCK PAWL BRACKET

a.
C282767

Install the parking lock rod sub-assembly, parking lock cam guide and the parking lock pawl bracket to the transaxle case with the 3 bolts.

Torque:
20.1 N*m (205 kgf*cm, 15 ft.*lbf)


Hide 35623Q 21.INSTALL NO. 2 1ST AND REVERSE BRAKE PISTON O-RING

a.
C282766

Coat 2 new No. 2 1st and reverse brake piston O-rings with Toyota Genuine ATF WS, and install them to the No. 2 1st and reverse brake piston.

NOTICE:

Do not damage the O-ring.



Hide 35623P 22.INSTALL NO. 2 1ST AND REVERSE BRAKE PISTON

a.
C282806

Install the No. 2 1st and reverse brake piston to the transaxle case.

NOTICE:

Do not damage the O-ring.



Hide 35068 23.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C282764E02
0.396,1.802 1.427,1.479 true 0.104,1.719 0.563,1.917 0.458,0.198 10 false SST

Install the 1st and reverse brake return spring sub-assembly to the transaxle case.


b.

Using SST, a press and a screwdriver, install the brake flange hole snap ring to the transaxle case.

SST
09387-00070  


Hide 35782C 24.INSTALL COUNTER DRIVE GEAR

a.
C283222E01
1.906,2.198 2.188,1.521 2.188,1.521 1.76,1.677 false 2.5,3.406 2.875,3.313 2.875,3.313 2.448,3.031 false 2.927,3.229 3.385,3.427 0.458,0.198 10 false SST 2.25,1.427 2.708,1.625 0.458,0.198 10 false SST

Using SST and a press, install the counter drive gear to the transaxle case.

SST
09223-15030  
09527-17011  
09950-60010  (09951-00650)
09950-70010  (09951-07150)


Hide 35720G 25.INSTALL PLANETARY GEAR ASSEMBLY

a.
C283223E01
1.906,2.281 2.156,1.396 2.156,1.396 1.76,1.573 false 2.479,3.583 2.854,3.438 2.854,3.438 2.438,3.167 false 2.208,1.313 2.667,1.51 0.458,0.198 10 false SST 2.896,3.354 3.354,3.552 0.458,0.198 10 false SST

Using SST and a press, install the planetary gear assembly to the transaxle case.

SST
09223-15030  
09527-17011  
09950-60010  (09951-00480)
09950-70010  (09951-07150)


Hide 35782H 26.INSTALL COUNTER DRIVE GEAR NUT

a.
C282761

Fix the counter driven gear with the parking lock pawl.


b.
C282807E01
1.188,1.563 0.479,0.604 true 0.188,0.5 0.646,0.698 0.458,0.198 10 false SST

Using SST, install a new counter drive gear lock nut lock washer and the counter drive gear nut.

SST
09387-00121  

Torque:
280 N*m (2855 kgf*cm, 207 ft.*lbf)


c.
C282808E01
0.521,0.656 1.198,1.542 true 0.188,0.406 0.646,0.604 0.458,0.198 10 false SST

Using SST and a torque wrench, measure the rotating torque while turning the counter drive gear at 60 turns per minute.

SST
09387-00121  

Rotating torque:

0.20 to 0.49 N*m (2.1 to 4.9 kgf*cm, 1.8 to 4.3 in.*lbf)



d.
C282809E01
1.51,0.302 1.865,1.104 true 1.219,0.198 1.677,0.396 0.458,0.198 10 false SST

Using SST and a hammer, stake the counter drive gear lock nut lock washer.

SST
09930-00010  


Hide 35683 27.INSTALL 1ST AND REVERSE BRAKE DISC

a.
C282810C01
1.302,0.344 1.698,0.771 false 1.708,0.188 2.021,0.698 false 1.531,0.094 1.844,0.292 0.313,0.198 10 false *1 1.135,0.229 1.448,0.427 0.313,0.198 10 false *2 2.823,1.24 3.135,1.438 0.313,0.198 10 false *4 1.135,0.583 1.448,0.781 0.313,0.198 10 false *3
*1 1st and Reverse Plate Snap Ring
*2 1st and Reverse Brake Flange
*3 1st and Reverse Brake Disc
*4 1st and Reverse Brake Plate


Install the 4 1st and reverse brake plates, 4 1st and reverse brake discs and the 1st and reverse brake flange to the transaxle case.


b.

Using a screwdriver, install the 1st and reverse plate snap ring to the transaxle case.


Hide 28.INSPECT PACK CLEARANCE OF 1ST AND REVERSE BRAKE

a.
C282811E01
1.667,0.854 2.615,0.281 true 0.438,0.25 0.594,0.25 false 2.667,0.167 3.125,0.365 0.458,0.198 10 false SST 0.635,0.167 0.938,0.365 0.302,0.198 10 true SST

Using SST and a dial indicator, measure the 1st and reverse brake clearance while pressing the 1st and reverse brake disc and the 1st and reverse brake plate from the rear side.

SST
09350-36010  (09350-06110)

Pack clearance:

0.806 to 1.206 mm (0.0318 to 0.0474 in.)


If the clearance is outside the specifications, select a new 1st and reverse brake flange.

HINT:

There are 4 different thicknesses of flanges available.


1st and Reverse Brake Flange Thickness:
Part No. Mark Thickness
mm (in.)
35679-52020 - 3.4 (0.134)
35679-52030 1 3.6 (0.142)
35679-52040 2 3.8 (0.150)
35679-52050 3 4.0 (0.157)



b.

Check that the 1st and reverse brake piston moves when compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) is applied to the oil hole.


Hide 35714D 29.INSTALL FRONT PLANETARY SUN GEAR

a.
C282812

Coat the front planetary gear thrust needle roller bearing with Toyota Genuine ATF WS, and install it to the planetary gear assembly.


b.

Install the front planetary sun gear to the planetary gear assembly.


Hide 35664D 30.INSTALL 2ND BRAKE CYLINDER O-RING

a.
C282758

Coat 2 new 2nd brake cylinder O-rings with Toyota Genuine ATF WS, and install them to the 2nd brake cylinder.

NOTICE:

Do not damage the O-ring.



Hide 35624E 31.INSTALL 2ND BRAKE PISTON

a.
C282813

Install the 2nd brake piston to the 2nd brake cylinder.

NOTICE:

Do not damage the O-ring.



Hide 35608L 32.INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C282756

Install the 2nd brake piston return spring sub-assembly to the 2nd brake cylinder.


b.
C287813E01
2.406,0.573 2.781,0.438 false 2.854,0.333 3.313,0.531 0.458,0.198 10 false SST

Place SST on the 2nd brake piston return spring sub-assembly, and compress the 2nd brake piston return spring sub-assembly with a press.

SST
09387-00060  


c.

Using a screwdriver, install the 2nd brake piston return spring snap ring to the 2nd brake cylinder.

NOTICE:

Make sure that the end gap of the snap ring is not aligned with the piston return spring claw.



Hide 34365A 33.INSTALL OUTER RACE RETAINER

a.
C282754

Install the outer race retainer to the No. 2 1-way clutch.


Hide 35792C 34.INSTALL NO. 2 1-WAY CLUTCH

a.
C282753

Install the No. 2 1-way clutch and the 2nd brake piston to the rear planetary gear assembly.


Hide 35720K 35.INSTALL REAR PLANETARY GEAR THRUST NEEDLE ROLLER BEARING

a.
C282814

Coat the thrust bearing race with Toyota Genuine ATF WS, and install it to the transaxle case.


b.

Coat the No. 2 thrust bearing race and the rear planetary gear thrust needle roller bearing with MP grease, and install them to the rear planetary gear assembly.


Hide 35760 36.INSTALL REAR PLANETARY GEAR ASSEMBLY

a.
C282815

Install the rear planetary gear assembly, 2nd brake piston and the No. 2 1-way clutch to the transaxle case.


b.

Using a screwdriver, install the No. 2 1-way clutch hole snap ring to the transaxle case.


Hide 35792C 37.INSPECT NO. 2 1-WAY CLUTCH

a.
C282750C01
0,0 0,0 false
V100135

Lock
V100136

Free


Check that the rear planetary gear assembly turns freely counterclockwise and locks when turned clockwise.

If the No. 2 1-way clutch does not operate normally, replace it.


Hide 35626D 38.INSTALL 2ND BRAKE PISTON SLEEVE

a.
C282749

Install the 2nd brake piston sleeve to the transaxle case.


Hide 35682 39.INSTALL 2ND BRAKE BRAKE DISC

a.
C282816C01
1.792,1.156 1.354,0.656 false 1.469,1.365 0.938,1.531 0.938,1.531 1.5,1.698 false 1.479,1.531 0.979,1.531 false 2.635,1.625 1.99,1.615 true 2,1.438 2.677,1.625 2.677,1.625 1.99,1.802 true 1.656,1.219 1.125,0.948 false 1.198,0.552 1.51,0.75 0.313,0.198 10 false *1 0.958,0.844 1.271,1.042 0.313,0.198 10 false *2 0.771,1.438 1.083,1.635 0.313,0.198 10 false *3 2.708,1.531 3.021,1.729 0.313,0.198 10 false *4
*1 2nd Brake Hole Snap Ring
*2 2nd Brake Brake Flange
*3 2nd Brake Brake Disc
*4 No. 1 2nd Brake Brake Flange


Install the 3 2nd brake brake discs, 3 No. 1 2nd brake brake flanges and the 2nd brake brake flange to the transaxle case.


b.

Using a screwdriver, install the 2nd brake hole snap ring to the transaxle case.


Hide 40.INSPECT PACK CLEARANCE OF 2ND BRAKE

a.
C282817

Using a dial indicator, measure the 2nd brake pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

Pack clearance:

0.847 to 1.247 mm (0.0334 to 0.0490 in.)


If the clearance is outside the specifications, select a new 2nd brake brake flange.

HINT:

There are 4 different thicknesses of flanges available.


2nd Brake Brake Flange Thickness:
Part No. Mark Thickness
mm (in.)
35678-52020 - 3.0 (0.118)
35678-52030 1 3.2 (0.126)
35678-52040 2 3.4 (0.134)
35678-52050 3 3.6 (0.142)



Hide 34625E 41.INSTALL 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING

a.
C282747

Using a screwdriver, install the 2nd coast and overdrive brake flange hole snap ring to the transaxle case.


Hide 35790A 42.INSTALL 1-WAY CLUTCH ASSEMBLY

a.
C282746

Coat the No. 2 planetary carrier thrust washer with Toyota Genuine ATF WS, and install it to the rear planetary sun gear assembly.


b.

Install the 1-way clutch assembly to the rear planetary sun gear assembly.


Hide 35790A 43.INSPECT 1-WAY CLUTCH ASSEMBLY

a.
C282745C01
0,0 0,0 false
V100135

Lock
V100136

Free


Hold the rear planetary sun gear assembly and turn the 1-way clutch assembly.


b.

Check that the 1-way clutch assembly turns freely counterclockwise and locks when turned clockwise.

If the 1-way clutch assembly does not operate normally, replace it.


Hide 35730B 44.INSTALL REAR PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING

a.
C282818

Coat the No. 1 planetary carrier thrust washer and the rear planetary sun gear thrust needle roller bearing with Toyota Genuine ATF WS, and install them to the transaxle case.


Hide 35730 45.INSTALL REAR PLANETARY SUN GEAR ASSEMBLY

a.
C282742

Install the rear planetary sun gear assembly and the 1-way clutch assembly to the transaxle case.


Hide 35730C 46.INSTALL REAR NO. 2 PLANETARY SUN GEAR THRUST NEEDLE ROLLER BEARING

a.
C282819

Coat the rear No. 2 planetary sun gear thrust needle roller bearing with Toyota Genuine ATF WS, and install it to the rear planetary sun gear assembly.


Hide 35654B 47.INSTALL DIRECT CLUTCH HUB

a.
C282740

Install the direct clutch hub to the transaxle case.


Hide 35605B 48.INSTALL THRUST NEEDLE ROLLER BEARING

a.
C282820

Coat the No. 3 thrust bearing race, thrust needle roller bearing and the C-2 hub thrust bearing race with Toyota Genuine ATF WS, and install them to the direct clutch hub.


Hide 35605D 49.INSTALL DIRECT CLUTCH DRUM O-RING

a.
C282737

Coat a new direct clutch drum O-ring with Toyota Genuine ATF WS, and install it to the direct clutch drum sub-assembly.

NOTICE:

Do not damage the O-ring.



Hide 35606C 50.INSTALL DIRECT CLUTCH PISTON O-RING

a.
C282736

Coat 2 new direct clutch piston O-rings with Toyota Genuine ATF WS, and install them to the direct clutch piston sub-assembly.

NOTICE:

Do not damage the O-ring.



Hide 35605A 51.INSTALL DIRECT CLUTCH DRUM SUB-ASSEMBLY

a.

Coat the direct clutch drum sub-assembly with Toyota Genuine ATF WS.


b.
C282822C01
2.698,0.792 2.906,0.844 true 2.677,0.135 3.031,0.25 true 3.052,0.167 3.25,0.375 0.198,0.208 10 false *a 2.938,0.76 3.125,0.927 0.188,0.167 10 true *b
*a Cutout
*b Matchmark


Align the cutout in the intermediate shaft sub-assembly with the matchmark on the direct clutch drum sub-assembly and install the direct clutch drum sub-assembly to the intermediate shaft sub-assembly.

NOTICE:

Do not damage the O-ring.



Hide 35606A 52.INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
C282823

Install the direct clutch piston sub-assembly to the intermediate shaft sub-assembly.

NOTICE:

Do not damage the O-ring.



Hide 35604 53.INSTALL DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C282733E01
2.552,0.875 2.823,0.875 false 2.875,0.802 3.333,1 0.458,0.198 10 false SST

Install the direct clutch return spring sub-assembly to the direct clutch piston sub-assembly.


b.

Place SST on the direct clutch return spring sub-assembly and compress the springs with a press.

SST
09387-00020  


c.

Using a snap ring expander, install the direct clutch piston shaft snap ring to the direct clutch drum sub-assembly.

NOTICE:
·

Stop pressing the press when the spring seat is lowered to 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring seat from deforming.

·

Do not expand the snap ring excessively.




Hide 35667A 54.INSTALL DIRECT CLUTCH DISC

a.
C282824C01
1.729,0.958 0.604,0.729 0.604,0.729 1.708,0.542 true 0.667,0.729 1.708,0.75 true 2.469,0.625 2.865,0.844 2.865,0.844 2.458,1.042 true 2.469,0.406 2.802,0.406 true 1.938,0.177 2.167,0.281 false 2.479,0.844 2.833,0.844 true 1.771,0.094 2.083,0.292 0.313,0.198 10 false *1 2.833,0.302 3.146,0.5 0.313,0.198 10 false *2 2.917,0.75 3.229,0.948 0.313,0.198 10 false *4 0.438,0.635 0.75,0.833 0.313,0.198 10 false *3
*1 Direct Clutch Flange Hole Snap Ring
*2 Direct Clutch Flange
*3 Direct Clutch Disc
*4 Rear Clutch Flange


Install the direct clutch flange, 3 direct clutch discs and the 3 rear clutch flanges to the intermediate shaft sub-assembly.


b.

Using a screwdriver, install the direct clutch flange hole snap ring to the intermediate shaft sub-assembly.


Hide 35677H 55.INSTALL REVERSE CLUTCH DISC

a.
C282825C01
2.146,0.177 2.417,0.396 true 1.813,0.354 2.073,0.531 true 1.948,0.677 1.688,0.625 1.688,0.625 1.938,0.854 true 2.688,0.938 2.917,0.865 2.917,0.865 2.677,0.75 true 1.625,0.25 1.938,0.448 0.313,0.198 10 false *2 1.99,0.083 2.302,0.281 0.313,0.198 10 false *1 2.958,0.76 3.354,0.99 0.396,0.229 10 false *4 1.51,0.542 1.906,0.771 0.396,0.229 10 false *3
*1 Reverse Clutch Flange Hole Snap Ring
*2 Reverse Clutch Flange
*3 Reverse Clutch Disc
*4 No. 3 Clutch Plate


Install the reverse clutch flange, 2 reverse clutch discs and the 2 No. 3 clutch plates to the intermediate shaft sub-assembly.


b.

Using a screwdriver, install the reverse clutch flange hole snap ring to the intermediate shaft sub-assembly.


Hide 56.INSPECT PACK CLEARANCE OF REVERSE CLUTCH

a.
C282826

Install the intermediate shaft sub-assembly and the rear clutch drum thrust needle roller bearing to the transaxle rear cover sub-assembly.


b.

Using a dial indicator, measure the reverse clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

Pack clearance:

0.862 to 1.262 mm (0.0340 to 0.0496 in.)


If the clearance is outside the specifications, select a new reverse clutch flange.

HINT:

There are 4 different thicknesses of flanges available.


Reverse Clutch Flange Thickness:
Part No. Mark Thickness
mm (in.)
35649-52020 - 3.0 (0.118)
35649-52030 1 3.2 (0.126)
35649-52040 2 3.4 (0.134)
35649-52050 3 3.6 (0.142)



Hide 57.INSPECT PACK CLEARANCE OF DIRECT CLUTCH

a.
C282827E01
2.156,1.385 2.875,1.781 true 2.927,1.708 3.281,1.927 0.354,0.219 10 false SST

Install the intermediate shaft sub-assembly and the rear clutch drum thrust needle roller bearing to the transaxle rear cover sub-assembly.


b.

Using SST and a dial indicator, measure the direct clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

SST
09350-36010  (09350-06110)

Pack clearance:

0.620 to 1.020 mm (0.0245 to 0.0401 in.)


If the clearance is outside the specifications, select a new direct clutch flange.

HINT:
·

The direct and reverse clutch will come out as the compressed air is applied. Therefore, while performing the check, press on the input shaft of the direct and reverse clutch using a stamping machine or the equivalent so that the pressure is not applied to the direct and reverse clutch.

·

There are 4 different thicknesses of flanges available.



Direct Clutch Flange Thickness:
Part No. Mark Thickness
mm (in.)
35675-52040 - 3.0 (0.118)
35675-52050 1 3.2 (0.126)
35675-52060 2 3.4 (0.134)
35675-52070 3 3.6 (0.142)



Hide 35102D 58.INSTALL TRANSAXLE REAR COVER NEEDLE ROLLER BEARING

a.
C282831E01
1.073,0.958 0.531,0.229 0.531,0.229 1.052,0.469 true 0.25,0.146 0.708,0.344 0.458,0.198 10 false SST

Coat a new transaxle rear cover needle roller bearing with Toyota Genuine ATF WS.


b.

Using SST and a press, install the transaxle rear cover needle roller bearing to the transaxle rear cover sub-assembly.

SST
09950-60010  (09951-00190, 09952-06010)
09950-70010  (09951-07100)

Standard depth:

25.2 mm (0.992 in.)



Hide 35617G 59.INSTALL CLUTCH DRUM OIL SEAL RING

a.
C282726

Coat 3 new clutch drum oil seal rings with Toyota Genuine ATF WS, and install them to the transaxle rear cover sub-assembly.

NOTICE:

Do not expand the clutch drum oil seal rings excessively.



Hide 34622C 60.INSTALL 2ND COAST AND OVERDRIVE O-RING

a.
C282725

Coat 2 new 2nd coast and overdrive O-rings with Toyota Genuine ATF WS, and install them to the 2nd coast and overdrive brake piston.

NOTICE:

Do not damage the O-ring.



Hide 34622B 61.INSTALL 2ND COAST AND OVERDRIVE BRAKE PISTON

a.
C282833

Install the 2nd coast and overdrive brake piston to the transaxle rear cover sub-assembly.

NOTICE:

Do not damage the O-ring.



Hide 34603B 62.INSTALL OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C287812

Install the overdrive brake return spring sub-assembly to the transaxle rear cover sub-assembly.


b.
C287811E01
1.781,2.24 2.146,2.063 false 2.01,0.854 2.635,0.531 true 2.708,0.438 3.167,0.635 0.458,0.198 10 false SST 2.198,1.958 2.656,2.156 0.458,0.198 10 false SST

Using SST, a press and a screwdriver, shorten the overdrive brake return spring sub-assembly, then install the overdrive brake return spring hole snap ring to the transaxle rear cover sub-assembly.

SST
09387-00070  

NOTICE:

Stop the press when the overdrive brake return spring sub-assembly is lowered to 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove, to prevent the overdrive brake return spring sub-assembly from being deformed.



Hide 35102B 63.INSTALL TRANSAXLE REAR COVER PLUG

a.
C282721

Coat 4 new O-rings with Toyota Genuine ATF WS, and install them to the 4 transaxle rear cover plugs.


b.

Install the 4 transaxle rear cover plugs to the transaxle rear cover sub-assembly.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)

NOTICE:

Do not damage the O-ring.



Hide 35708G 64.INSTALL INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
C282730

Install the intermediate shaft sub-assembly to the transaxle case.


Hide 34633 65.INSTALL 2ND COAST AND OVERDRIVE BRAKE DISC

a.
C282821C01
1.823,0.927 2.438,0.927 true 1.823,1.125 2.354,1.583 2.354,1.583 1.823,1.313 true 1.313,1.031 0.833,1.083 0.833,1.083 1.313,1.198 true 2.49,0.823 2.802,1.021 0.313,0.198 10 false *1 0.646,0.979 0.958,1.177 0.313,0.198 10 false *2 2.406,1.531 2.719,1.729 0.313,0.198 10 false *3
*1 2nd Coast and Overdrive Brake Flange
*2 2nd Coast and Overdrive Brake Disc
*3 No. 2 2nd Coast and Overdrive Brake Flange


Install the 2 2nd coast and overdrive brake discs, 2 No. 2 2nd coast and overdrive brake flanges and the 2nd coast and overdrive brake flange to the transaxle case.


Hide 66.INSPECT CLEARANCE OF 2ND COAST AND OVERDRIVE BRAKE

a.
C282828E01
0.177,0.313 0.333,0.51 0.156,0.198 10 false A

As shown in the illustration, place a straightedge on the transaxle case and measure the distance between the 2nd coast and overdrive brake flange and straightedge using a vernier caliper. (Dimension A)


b.
C282829E01
2.906,0.833 3.063,1.031 0.156,0.198 10 false B

As shown in the illustration, place a straightedge on the 2nd coast and overdrive brake piston and measure the distance between the transaxle rear cover sub-assembly and straightedge using a vernier caliper. (Dimension B)

Calculate the piston stroke value using the following formula. Select a 2nd coast and overdrive brake flange which meets the piston stroke value and install it.

HINT:

Pack clearance = Dimension A - Dimension B


Pack clearance:

2.091 to 2.491 mm (0.0824 to 0.0980 in.)


If the clearance is outside the specifications, select a new 2nd coast and overdrive brake flange.

HINT:

There are 4 different thicknesses of flanges available.


2nd Coast and Overdrive Brake Flange Thickness:
Part No. Mark Thickness
mm (in.)
34625-52110 4 4.0 (0.157)
34625-52071 5 4.2 (0.165)
34625-52081 6 4.4 (0.173)
34625-52091 7 4.6 (0.181)



Hide 35651B 67.INSTALL REAR CLUTCH DRUM THRUST NEEDLE ROLLER BEARING

a.
C282830

Coat the rear clutch drum thrust needle roller bearing with MP grease, and install it to the transaxle rear cover sub-assembly.


Hide 68.INSPECT INTERMEDIATE SHAFT END PLAY

a.

Remove any remaining seal packing from the contact surfaces of the transaxle rear cover sub-assembly and transaxle case.


b.
C287818

Install the transaxle rear cover sub-assembly to the transaxle case with the 11 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


c.
C282718

Using a dial indicator, measure the intermediate shaft end play.

Standard end play:

0.204 to 0.966 mm (0.00804 to 0.0380 in.)


If the end play is not as specified, select and replace the rear clutch drum thrust needle roller bearing.

HINT:

There are 2 different thicknesses of thrust needle roller bearings available.


Rear Clutch Drum Thrust Needle Roller Bearing Thickness:
Part No. Color Thickness
mm (in.)
90374-43004 Brown 2.5 (0.0984)
90374-43005 Black 2.8 (0.110)



d.

Remove the 11 bolts and the transaxle rear cover sub-assembly.


Hide 35102 69.INSTALL TRANSAXLE REAR COVER SUB-ASSEMBLY

a.

Remove any remaining seal packing from the contact surfaces of the transaxle rear cover sub-assembly and transaxle case.

NOTICE:

Make sure that there is no ATF on the contact surfaces.



b.
C282728

Coat 4 new O-rings with Toyota Genuine ATF WS, and install them to the transaxle case.


c.
C282834C01
0.5,0.969 0.958,0.979 true 0.281,0.875 0.594,1.073 0.313,0.198 10 false *a
*a Seal Packing


Apply a continuous bead of seal packing (width 1.2 mm (0.0472 in.)) to the transaxle case sealing surface as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.



d.
C287818

Install the transaxle rear cover sub-assembly to the transaxle case with the 11 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 35061 70.INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY

a.
C282719

Install the forward clutch hub sub-assembly to the transaxle case.


Hide 35061C 71.INSTALL FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING

a.
C282835

Coat the forward clutch hub thrust needle roller bearing with Toyota Genuine ATF WS, and install it to the forward clutch hub sub-assembly.


Hide 35712A 72.INSTALL INPUT SHAFT OIL SEAL RING

a.
C287810

Coat a new input shaft oil seal ring with Toyota Genuine ATF WS, and install it to the input shaft sub-assembly.


Hide 35612C 73.INSTALL FORWARD CLUTCH PISTON O-RING

a.
C282715

Coat a new forward clutch piston O-ring with Toyota Genuine ATF WS, and install it to the forward clutch piston.


Hide 35612B 74.INSTALL FORWARD CLUTCH PISTON

a.
C282836

Coat the forward clutch piston with Toyota Genuine ATF WS, and install it to the input shaft sub-assembly.

NOTICE:

Do not damage the O-ring.



Hide 35603A 75.INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C282837

Install the forward clutch return spring sub-assembly to the input shaft sub-assembly.


b.

Coat the No. 1 clutch balancer with Toyota Genuine ATF WS, and install it to the input shaft sub-assembly.


c.
C282712E03
1,0.635 1.583,0.958 false 0.698,0.542 1.156,0.74 0.458,0.198 10 false SST

Using SST on the No. 1 clutch balancer, compress the forward clutch return spring sub-assembly with a press.

SST
09320-89010  


d.

Using a snap ring expander, install the clutch balancer snap ring to the input shaft sub-assembly.


Hide 35633 76.INSTALL FRONT CLUTCH CLUTCH DISC

a.
C282838C01
1.99,0.823 1.24,0.344 1.24,0.344 1.948,0.938 true 1.865,0.281 2.146,0.438 false 1.969,0.688 1.26,0.354 1.26,0.354 1.938,0.563 true 2.219,0.167 2.438,0.385 false 2.531,0.76 2.927,0.75 2.927,0.75 2.521,0.635 true 2.531,1.01 2.917,0.75 2.917,0.75 2.521,0.885 true 2.969,0.656 3.281,0.854 0.313,0.198 10 false *4 1.073,0.24 1.385,0.438 0.313,0.198 10 false *3 1.688,0.167 2,0.365 0.313,0.198 10 false *2 2.052,0.052 2.365,0.25 0.313,0.198 10 false *1
*1 Forward Clutch Flange Hole Snap Ring
*2 Forward Clutch Flange
*3 Front Clutch Clutch Disc
*4 No. 1 Clutch Plate


Install the forward clutch flange, 4 front clutch clutch discs and the 4 No. 1 clutch plates to the input shaft sub-assembly.


b.

Using a screwdriver, install the forward clutch flange hole snap ring to the input shaft sub-assembly.


Hide 77.INSPECT PACK CLEARANCE OF FORWARD CLUTCH

a.
C282839

Using a dial indicator, measure the pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

Pack clearance:

1.406 to 1.806 mm (0.0554 to 0.0711 in.)


If the clearance is outside the specifications, select a new forward clutch flange.

HINT:

There are 4 different thicknesses of flanges available.


Forward Clutch Flange Thickness:
Part No. Mark Thickness
mm (in.)
35635-52050 - 3.0 (0.118)
35635-52060 1 3.2 (0.126)
35635-52070 2 3.4 (0.134)
35635-52080 3 3.6 (0.142)



Hide 35370A 78.INSTALL STATOR SHAFT THRUST NEEDLE ROLLER BEARING

a.
C282840

Coat the stator shaft thrust needle roller bearing with Toyota Genuine ATF WS, and install it to the input shaft sub-assembly.


Hide 35701 79.INSTALL INPUT SHAFT SUB-ASSEMBLY

a.
C282709

Install the input shaft sub-assembly to the transaxle case.


Hide 80.INSTALL DIFFERENTIAL GEAR ASSEMBLY

a.
C282707

Install the differential gear assembly to the transaxle case.


Hide 81.INSTALL OIL PUMP ASSEMBLY

a.
C282706

Install the oil pump assembly to the transaxle case with the 7 bolts.

Torque:
22.1 N*m (225 kgf*cm, 16 ft.*lbf)


Hide 35701 82.INSPECT INPUT SHAFT SUB-ASSEMBLY

a.
C282841

Make sure that the input shaft sub-assembly turns smoothly.

If the input shaft sub-assembly does not operate normally, replace it.


Hide 83.INSPECT INPUT SHAFT END PLAY

a.
C282705

Using a dial indicator, measure the input shaft end play.

Standard end play:

0.374 to 1.292 mm (0.0148 to 0.0508 in.)


If the end play is not as specified, replace the stator shaft thrust needle roller bearing and the forward clutch hub thrust needle roller bearing.


Hide 35111C 84.INSTALL TRANSAXLE HOUSING

a.

Remove any remaining seal packing from the contact surfaces of the transaxle housing and transaxle case.

NOTICE:

Make sure that there is no ATF on the contact surfaces.



b.
C282708

Coat 2 new O-rings with Toyota Genuine ATF WS, and install them to the transaxle case.


c.
C282842C01
2.656,0.573 3.01,0.302 true 3.063,0.167 3.375,0.365 0.313,0.198 10 false *a
*a Seal Packing


Apply a continuous bead of seal packing (width 1.2 mm (0.0472 in.)) to the transaxle case sealing surface as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.



d.
A192239C42
1.698,1.5 1.698,1.74 false 1.646,1.75 1.823,1.906 0.177,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads on the ends of the 3 bolts B.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



e.
C282704E01
0.5,1.813 0.656,2.01 0.156,0.198 10 false A 1.073,1.99 1.229,2.177 0.156,0.188 10 false A 1.396,1.948 1.552,2.146 0.156,0.198 10 false A 0.208,1.271 0.365,1.469 0.156,0.198 10 false A 0.302,0.604 0.458,0.802 0.156,0.198 10 false A 2.688,0.354 2.844,0.552 0.156,0.198 10 false A 2.917,0.958 3.073,1.156 0.156,0.198 10 false A 0.677,0.219 0.833,0.417 0.156,0.198 10 false A 2.073,0.073 2.229,0.271 0.156,0.198 10 false A 1.667,0.031 1.823,0.229 0.156,0.198 10 false A 1.104,0.073 1.26,0.271 0.156,0.198 10 false A 1.667,1.833 1.823,2.031 0.156,0.198 10 false B 2.313,1.823 2.469,2.021 0.156,0.198 10 false B 2.74,1.542 2.896,1.74 0.156,0.198 10 false B

Install the transaxle housing to the transaxle case with the 14 bolts.

Torque:
Bolt A : 29.4 N*m (300 kgf*cm, 22 ft.*lbf)
Bolt B : 22.1 N*m (225 kgf*cm, 16 ft.*lbf)


Hide 35425A 85.INSTALL C-2 ACCUMULATOR PISTON

a.
C282703

Coat 2 new C-2 accumulator piston O-rings with Toyota Genuine ATF WS, and install them to the C-2 accumulator piston.

NOTICE:

Do not damage the O-ring.



b.
C282843

Install the C-2 accumulator piston compression spring and the C-2 accumulator piston to the transaxle case.

Accumulator Spring:
Spring Free Length/
Outer Diameter mm (in.)
Color
C-2 66.9 (2.63)
17.2 (0.677)
-



Hide 35426D 86.INSTALL C-3 ACCUMULATOR PISTON

a.
C282701

Coat 2 new C-3 accumulator piston O-rings with Toyota Genuine ATF WS, and install them to the C-3 accumulator piston.

NOTICE:

Do not damage the O-ring.



b.
C282844

Install the C-3 accumulator piston compression spring and the C-3 accumulator piston to the transaxle case.

Accumulator Spring:
Spring Free Length/
Outer Diameter mm (in.)
Color
C-3 80.2 (3.16)
18.7 (0.736)
Blue



Hide 35423 87.INSTALL B-2 ACCUMULATOR PISTON

a.
C282699

Coat 2 new B-2 accumulator piston O-rings with Toyota Genuine ATF WS, and install them to the B-2 accumulator piston.

NOTICE:

Do not damage the O-ring.



b.
C282845

Install the B-2 accumulator piston compression spring and the B-2 accumulator piston to the transaxle case.

Accumulator Spring:
Spring Free Length/
Outer Diameter mm (in.)
Color
B-2 66.9 (2.63)
15.5 (0.610)
Green



Hide 35251 88.INSTALL CHECK BALL BODY

a.
C282697

Install the check ball body compression spring and the check ball body to the transaxle case.


Hide 35159 89.INSTALL BRAKE DRUM GASKET

a.
C282696

Install a new brake drum gasket to the transaxle case.


Hide 35149B 90.INSTALL TRANSAXLE CASE 2ND BRAKE GASKET

a.
C282694

Coat a new transaxle case 2nd brake gasket with Toyota Genuine ATF WS, and install it to the transaxle case.


Hide 35145C 91.INSTALL TRANSAXLE CASE GASKET

a.
C282695

Coat a new transaxle case gasket with Toyota Genuine ATF WS, and install it to the transaxle case.


Hide 82125J 92.INSTALL TRANSMISSION WIRE

a.
C282693

Coat a new O-ring with Toyota Genuine ATF WS, and install it to the transmission wire.

NOTICE:

Do not damage the O-ring.



b.
C282388

Pass the transmission wire through the transaxle case.


c.
C282692

Install the transmission wire to the transaxle case with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Do not damage the O-ring.



Hide 35410 93.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C283428C01
2.885,0.969 2.885,0.51 true 3.167,0.927 3.042,0.458 true 2.823,0.979 3.021,1.177 0.198,0.198 10 false *1 3.125,0.948 3.313,1.146 0.188,0.198 10 false *2 2.26,0.104 2.396,0.281 0.135,0.177 10 true A 1.573,0 1.708,0.177 0.135,0.177 10 true A 1.302,0 1.438,0.177 0.135,0.177 10 true A 0.51,1.51 0.646,1.688 0.135,0.177 10 false A 2.646,0.813 2.781,0.99 0.135,0.177 10 false B 1.844,0 1.979,0.177 0.135,0.177 10 true B 0.802,0.052 0.938,0.229 0.135,0.177 10 true B 1.427,1.313 1.563,1.49 0.135,0.177 10 true B 0.458,1.281 0.594,1.458 0.135,0.177 10 false B 0.427,1.021 0.563,1.198 0.135,0.177 10 false C 0.427,0.792 0.563,0.969 0.135,0.177 10 false C 1.417,1.031 1.552,1.208 0.135,0.177 10 true D 1.396,0.823 1.531,1 0.135,0.177 10 true D
*1 Manual Valve
*2 Manual Valve Lever Sub-assembly


Align the groove of the manual valve with the pin of the manual valve lever sub-assembly.


b.

Temporarily install the transmission valve body assembly to the transaxle case with the 13 bolts.

HINT:

Bolt length:

·

Bolt A: 20 mm (0.787 in.)

·

Bolt B: 32 mm (1.26 in.)

·

Bolt C: 45 mm (1.77 in.)

·

Bolt D: 55 mm (2.17 in.)




c.
C282690C02
2.208,0.792 2.75,0.583 true 2.229,1.229 2.75,1.406 true 2.781,0.479 3.094,0.635 0.313,0.156 10 false *1 2.792,1.323 3.104,1.479 0.313,0.156 10 false *2 2.542,1.01 2.698,1.208 0.156,0.198 10 false A 2.427,1.51 2.583,1.708 0.156,0.198 10 true B
*1 Manual Detent Spring Sub-assembly
*2 Manual Detent Spring Cover


Temporarily install the manual detent spring sub-assembly and the manual detent spring cover to the transmission valve body assembly with the 2 bolts.

HINT:

Bolt length:

·

Bolt A: 14 mm (0.551 in.)

·

Bolt B: 45 mm (1.77 in.)




d.

Check that the manual valve lever sub-assembly comes into contact with the center of the roller at the tip of the manual detent spring sub-assembly.


e.

Tighten the 15 bolts.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)


f.
C282689

Connect the 5 connectors to the transmission valve body assembly.


g.

Coat the ATF temperature sensor O-ring on the transmission wire with Toyota Genuine ATF WS.


h.

Install the transmission wire to the transmission valve body assembly with the temperature sensor clamp and the bolt.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)

HINT:

Bolt length: 55 mm (2.17 in.)



Hide 35330 94.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.
C282688

Coat a new oil strainer O-ring with Toyota Genuine ATF WS, and install it to the valve body oil strainer assembly.


b.
C282687

Install the valve body oil strainer assembly to the transmission valve body assembly with the 3 bolts.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)


Hide 35394 95.INSTALL TRANSMISSION OIL CLEANER MAGNET

a.
C282686

Install the 2 transmission oil cleaner magnets to the automatic transaxle oil pan sub-assembly.


Hide 35106D 96.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
A192239C42
1.698,1.5 1.698,1.74 false 1.646,1.75 1.823,1.906 0.177,0.156 10 false *a
*a Adhesive


Clean and degrease 2 bolts A and bolt holes.


b.

Apply adhesive to 2 or 3 threads on the ends of the 2 bolts A.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.
C282685E01
2.521,0.938 2.677,1.135 0.156,0.198 10 true A 2.51,0.688 2.667,0.885 0.156,0.198 10 false A 2.448,0.208 2.604,0.406 0.156,0.198 10 false B 1.938,0.031 2.094,0.229 0.156,0.198 10 false B 1.688,0.031 1.844,0.229 0.156,0.198 10 false B 1.427,0.042 1.583,0.24 0.156,0.198 10 false B 1.177,0.042 1.333,0.24 0.156,0.198 10 false B 0.969,0.042 1.125,0.24 0.156,0.198 10 false B 0.5,0.302 0.656,0.5 0.156,0.198 10 false B 0.396,0.552 0.552,0.75 0.156,0.198 10 false B 0.344,1.01 0.5,1.208 0.156,0.198 10 false B 0.344,1.271 0.5,1.469 0.156,0.198 10 false B 0.469,1.781 0.625,1.979 0.156,0.198 10 false B 0.958,1.979 1.115,2.177 0.156,0.198 10 true B 1.229,1.979 1.385,2.177 0.156,0.198 10 true B 1.521,1.979 1.677,2.177 0.156,0.198 10 true B 2.042,1.833 2.198,2.031 0.156,0.198 10 true B 2.229,1.635 2.385,1.833 0.156,0.198 10 true B 2.417,1.438 2.573,1.635 0.156,0.198 10 true B

Install a new automatic transaxle oil pan gasket and the automatic transaxle oil pan sub-assembly to the transaxle case with the 19 bolts.

Torque:
Bolt A : 7.4 N*m (75 kgf*cm, 65 in.*lbf)
Bolt B : 7.8 N*m (80 kgf*cm, 69 in.*lbf)

NOTICE:

Completely remove any oil or grease from the contact surface of the transaxle case and the automatic transaxle oil pan sub-assembly with the automatic transaxle oil pan gasket before installation.



d.

Using a 10 mm hexagon socket wrench, install a new gasket and the drain plug sub-assembly to the automatic transaxle oil pan sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 35104B 97.INSTALL BREATHER PLUG

a.
C284801

Coat a new O-ring with Toyota Genuine ATF WS, and install it to the breather plug.

NOTICE:

Do not damage the O-ring.



b.

Install the breather plug to the transaxle case.

NOTICE:

Do not damage the O-ring.



Hide 35012 98.INSTALL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

a.
C287808

Install the transmission breather hose sub-assembly to the breather plug.


Hide 35104Q 99.INSTALL NO. 1 TRANSAXLE CASE PLUG

a.
C282682

Coat 5 new O-rings with Toyota Genuine ATF WS, and install them to the No. 1 transaxle case plugs.

NOTICE:

Do not damage the O-ring.



b.

Install the 4 No. 1 transaxle case plugs to the transaxle housing and the transaxle case.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)

NOTICE:

Do not damage the O-ring.



c.
C282683

Install the No. 1 transaxle case plug to the transaxle case.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)

NOTICE:

Do not damage the O-ring.



Hide 32921C 100.INSTALL OIL COOLER TUBE UNION

a.
C282681

Coat 2 new O-rings with Toyota Genuine ATF WS, and install them to the 2 oil cooler tube unions.

NOTICE:

Do not damage the O-ring.



b.

Install the 2 oil cooler tube unions to the transaxle case.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:

Do not damage the O-ring.



Hide 89413B 101.INSTALL TRANSMISSION REVOLUTION SENSOR

a.
C282680

Coat a new O-ring with Toyota Genuine ATF WS, and install it to the transmission revolution sensor.

NOTICE:

Do not damage the O-ring.



b.

Install the transmission revolution sensor to the transaxle case with the bolt.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)

NOTICE:

Do not damage the O-ring.



Hide 84540 102.INSTALL PARK/NEUTRAL POSITION SWITCH

a.
C117106

Temporarily install the park/neutral position switch to the transaxle case with the 2 bolts.


b.
C293451

Install a new lock plate and the lock nut to the park/neutral position switch.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


c.

Temporarily install the transmission control shaft lever to the manual valve lever shaft.


d.
C117103C01
0.823,2 1.135,2.156 0.313,0.156 10 false *a 0.406,1.375 0.604,1.542 0.198,0.167 10 true *b
*a P Position
*b N Position


Rotate the transmission control shaft lever counterclockwise until it stops, and then from that position rotate it clockwise by 2 notches to set it to the N position.


e.

Remove the transmission control shaft lever from the manual valve lever shaft.


f.
C117107C02
0.458,0.771 1.542,0.917 true 0.448,1.281 1.604,1.156 true 0.302,0.677 0.615,0.833 0.313,0.156 10 false *a 0.292,1.188 0.604,1.344 0.313,0.156 10 false *b
*a Neutral Basic Line
*b Protrusion


Rotate the park/neutral position switch clockwise or counterclockwise to align the neutral basic line with the protrusion as shown in the illustration.


g.

Hold the park/neutral position switch in this position and tighten the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


h.
C117105

Using a screwdriver, stake the nut with the lock plate.


Hide 35572A 103.INSTALL TRANSMISSION CONTROL SHAFT LEVER

a.
C282395

Install the transmission control shaft lever to the manual valve lever shaft with the washer and the nut.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)