Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › OIL PUMP › 2013.08–2016.10
RM30M0E _52 Drivetrain _017087 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090616 OIL PUMP G

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL PUMP  INSPECTION  


PROCEDURE

Hide 35370 1.INSPECT STATOR SHAFT ASSEMBLY

a.
C282863

Using a caliper gauge, measure the inside diameter of the stator shaft bushing.

Standard inside diameter:

21.500 to 21.526 mm (0.8465 to 0.8474 in.)


Maximum inside diameter:

21.526 mm (0.8474 in.)


If the inside diameter is greater than the maximum, replace the stator shaft assembly.


b.
C282864

Install the input shaft assembly onto the stator shaft assembly and check that the input shaft assembly turns smoothly.

NOTICE:

Replace the stator shaft assembly with a new one if it moves roughly or makes unusual noise.

Inspect the input shaft's contact surface with the bearing when replacing, and replace the input shaft with a new one if any damage or discoloration is found.



Hide 35301 2.INSPECT FRONT OIL PUMP BODY

a.
C282865

Using a caliper gauge, measure the inside diameter of the front oil pump body bushing.

Standard inside diameter:

38.113 to 38.138 mm (1.5006 to 1.5014 in.)


Maximum inside diameter:

38.138 mm (1.5014 in.)


If the inside diameter is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear and the front oil pump body.


Hide 3.INSPECT FRONT OIL PUMP GEAR CLEARANCE

a.
C282866

Using a feeler gauge, measure the clearance between the tips of the front oil pump driven gear teeth and the front oil pump drive gear teeth.

Standard tip clearance:

0.07 to 0.15 mm (0.00276 to 0.00590 in.)


Maximum tip clearance:

0.15 mm (0.00590 in.)


If the tip clearance is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear and the front oil pump body.


b.
C282867

Using a feeler gauge, measure the clearance while push the front oil pump driven gear to one side of the front oil pump body.

Standard body clearance:

0.10 to 0.15 mm (0.00394 to 0.00590 in.)


Maximum body clearance:

0.15 mm (0.00590 in.)


If the body clearance is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear and the front oil pump body.


c.
C282868

Using a straightedge and a feeler gauge, measure the side clearance of the front oil pump drive gear and the front oil pump driven gear.

Standard side clearance:

0.02 to 0.05 mm (0.000788 to 0.00196 in.)


Maximum side clearance:

0.05 mm (0.00196 in.)


If the side clearance is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear and the front oil pump body.

Front Oil Pump Drive Gear Thickness:
Part No. Mark Thickness
mm (in.)
35321-52060 1 9.44 to 9.45 (0.3717 to 0.3720)
35321-52070 2 9.45 to 9.46 (0.3721 to 0.3724)
35321-52080 3 9.46 to 9.47 (0.3725 to 0.3728)
35321-52090 4 9.47 to 9.48 (0.3729 to 0.3732)
35321-52100 5 9.48 to 9.49 (0.3733 to 0.3736)


Front Oil Pump Driven Gear Thickness:
Part No. Mark Thickness
mm (in.)
35322-52060 1 9.44 to 9.45 (0.3717 to 0.3720)
35322-52070 2 9.45 to 9.46 (0.3721 to 0.3724)
35322-52080 3 9.46 to 9.47 (0.3725 to 0.3728)
35322-52090 4 9.47 to 9.48 (0.3729 to 0.3732)
35322-52100 5 9.48 to 9.49 (0.3733 to 0.3736)