The park/neutral position switch detects the shift lever position and sends signals to the ECM.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0705 | Transmission Range Sensor Circuit Malfunction (PRNDL Input) | One of the following conditions (A), (B) or (C) is met:
Condition (A): Any 2 or more of the following signals are ON simultaneously (2 trip detection logic). ·
One of the following conditions is met. P input signal is ON. N input signal is ON. NSW input signal is ON. ·
R input signal is ON. ·
D input signal is ON. ·
2 input signal is ON. ·
L input signal is ON. Condition (B): All switches are OFF simultaneously (2 trip detection logic). ·
P input signal is OFF. ·
N input signal is OFF. ·
NSW input signal is OFF. ·
R input signal is OFF. ·
D input signal is OFF. ·
2 input signal is OFF. ·
L input signal is OFF. Condition (C): When any of following conditions is met, the 3 position input signal is ON for 2 seconds or more (2 trip detection logic). ·
NSW input signal is ON. ·
P input signal is ON. ·
R input signal is ON. ·
N input signal is ON. ·
2 input signal is ON. ·
L input signal is ON. |
·
Wire harness or connector ·
Park/neutral position switch ·
Transmission control switch (Shift lock control unit assembly) ·
ECM |
Comes on | DTC stored |
This DTC indicates a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.
The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For safety, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the ECM according to the shift position (P, R, N, D, 2 or L). The ECM determines that there is a problem with the switch or related parts if it receives 2 or more position signals simultaneously or it receives no position signal. The ECM turns on the MIL and stores the DTC.
Inspect the fuses for circuits related to this system before performing the following procedure.
DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| Neutral Position SW Signal |
| Shift SW Status (P Range) |
| Shift SW Status (R Range) |
| Shift SW Status (2 Range) |
| Shift SW Status (L Range) |
| Shift SW Status (N Range) |
| Shift SW Status (D Range) |
| Shift SW Status (3 Range) |
In accordance with the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral Position SW Signal | Park/neutral position switch status | OFF or ON | ·
OFF: Shift lever not in P and N ·
ON: Shift lever in P or N |
When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (P Range) | Park/neutral position switch status | OFF or ON | ·
OFF: Shift lever not in P ·
ON: Shift lever in P |
When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (R Range) | Park/neutral position switch status | OFF or ON | ·
OFF: Shift lever not in R ·
ON: Shift lever in R |
When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (2 Range) | Park/neutral position switch status | OFF or ON | ·
OFF: Shift lever not in 2 ·
ON: Shift lever in 2 |
When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (L Range) | Park/neutral position switch status | OFF or ON | ·
OFF: Shift lever not in L ·
ON: Shift lever in L |
When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (N Range) | Park/neutral position switch status | OFF or ON | ·
OFF: Shift lever not in N ·
ON: Shift lever in N |
When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (D Range) | Park/neutral position switch status | OFF or ON | ·
OFF: Shift lever not in D and 3 ·
ON: Shift lever in D or 3 |
When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect. |
| Shift SW Status (3 Range) | Park/neutral position switch status | OFF or ON | ·
OFF: Shift lever not in 3 ·
ON: Shift lever in 3 |
When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect. |
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch) |
Disconnect the park/neutral position switch connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B19-2 (RB) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Park/Neutral Position Switch) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B19-4 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Park/Neutral Position Switch) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (B) - 5 (L) | Shift lever in P or N | Below 1 Ω |
| Shift lever not in P and N | 10 kΩ or higher | |
| 2 (RB) - 6 (PL) | Shift lever in P | Below 1 Ω |
| Shift lever not in P | 10 kΩ or higher | |
| 1 (RL) - 2 (RB) | Shift lever in R | Below 1 Ω |
| Shift lever not in R | 10 kΩ or higher | |
| 2 (RB) - 9 (NL) | Shift lever in N | Below 1 Ω |
| Shift lever not in N | 10 kΩ or higher | |
| 2 (RB) - 7 (DL) | Shift lever in D or 3 | Below 1 Ω |
| Shift lever not in D and 3 | 10 kΩ or higher | |
| 2 (RB) - 3 (2L) | Shift lever in 2 | Below 1 Ω |
| Shift lever not in 2 | 10 kΩ or higher | |
| 2 (RB) - 8 (LL) | Shift lever in L | Below 1 Ω |
| Shift lever not in L | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>U441E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
| *a | Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly)) |
Disconnect the F19 transmission control switch (shift lock control unit assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | Shift lever in 3 or 2 | Below 1 Ω |
| Shift lever not in 3 and 2 | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Transmission Control Switch (Shift Lock Control Unit Assembly)) |
Connect the B19 park/neutral position switch connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F19-1 - Body ground | Ignition switch ON
Shift lever in D or 3 |
11 to 14 V |
| Ignition switch ON
Shift lever not in D and 3 |
Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F19 transmission control switch (shift lock control unit assembly) connector.
Turn the ignition switch to ON.
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F82-8 (3) - Body ground | Ignition switch ON
Shift lever in 3 |
11 to 14 V |
| Ignition switch ON
Shift lever not in 3 |
Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch to ON.
| *a | Component with harness connected
(ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B31-34 (P) - Body ground | Ignition switch ON Shift lever in P | 11 to 14 V |
| Ignition switch ON Shift lever not in P | Below 1 V | |
| B31-17 (R) - Body ground | Ignition switch ON Shift lever R | 11 to 14 V* |
| Ignition switch ON Shift lever not in R | Below 1 V | |
| B31-26 (N) - Body ground | Ignition switch ON Shift lever in N | 11 to 14 V |
| Ignition switch ON Shift lever not in N | Below 1 V | |
| F82-21 (D) - Body ground | Ignition switch ON Shift lever in D or 3 | 11 to 14 V |
| Ignition switch ON Shift lever not in D and 3 | Below 1 V | |
| B31-18 (2) - Body ground | Ignition switch ON Shift lever in 2 | 11 to 14 V |
| Ignition switch ON Shift lever not in 2 | Below 1 V | |
| B31-16 (L) - Body ground | Ignition switch ON Shift lever in L | 11 to 14 V |
| Ignition switch ON Shift lever not in L | Below 1 V |
*: The voltage will drop slightly due to the back up light being turned on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F82 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F82-9 (NSW) - B19-4 (B) | Always | Below 1 Ω |
| B19-4 (B) or F82-9 (NSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG