Home › Drivetrain › U441E AUTOMATIC TRANSMISSION / TRANSAXLE › VALVE BODY ASSEMBLY › 2013.08–2016.07
RM30M0E _52 Drivetrain _017088 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0090622 VALVE BODY ASSEMBLY A

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 35148 1.INSTALL NO. 1 GOVERNOR APPLY GASKET

a.

Apply a light coat of Toyota Genuine ATF Type T-IV to a new No. 1 governor apply gasket and install it to the automatic transaxle case sub-assembly.


Hide 35251 2.INSTALL CHECK BALL BODY

a.

Install the check ball body compression spring and check ball body to the automatic transaxle case sub-assembly.


Hide 35410 3.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.

Connect the manual valve connecting rod to the manual valve lever sub-assembly.


b.
C203894N01
2.208,1.708 2.365,1.906 0.156,0.198 10 true A 2.792,1.063 2.948,1.26 0.156,0.198 10 true A 2.667,0.521 2.823,0.719 0.156,0.198 10 false A 1.99,0.073 2.146,0.271 0.156,0.198 10 false A 1.729,0.073 1.885,0.271 0.156,0.198 10 false A 1.427,0.083 1.583,0.281 0.156,0.198 10 false A 0.438,1.021 0.594,1.219 0.156,0.198 10 false B 0.448,1.396 0.604,1.594 0.156,0.198 10 false B 0.813,1.979 0.969,2.177 0.156,0.198 10 false B 1.25,1.927 1.406,2.125 0.156,0.198 10 false B 1.448,0.948 1.604,1.146 0.156,0.198 10 true B 1.833,1.75 1.99,1.948 0.156,0.198 10 false C 0.74,0.448 0.896,0.646 0.156,0.198 10 true D 1.563,1.792 1.719,1.99 0.156,0.198 10 true E

Temporarily install the transmission valve body assembly to the automatic transaxle case sub-assembly with the 14 bolts.

HINT:

Bolt length:

·

Bolt A: 20 mm (0.787 in.)

·

Bolt B: 28 mm (1.10 in.)

·

Bolt C: 36 mm (1.42 in.)

·

Bolt D: 40 mm (1.57 in.)

·

Bolt E: 49 mm (1.93 in.)




c.

Tighten the 14 bolts.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)


Hide 82125J 4.CONNECT TRANSMISSION WIRE

a.

Engage the 2 clamps, connect the 5 connectors and install the transmission wire to the transmission valve body assembly.


b.

Engage the temperature sensor clamp and install the transmission wire to the transmission valve body assembly.


Hide 35330 5.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.

Apply a light coat of Toyota Genuine ATF Type T-IV to the gasket of the valve body oil strainer assembly.


b.

Install the valve body oil strainer assembly to the transmission valve body assembly with the 3 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35394 6.INSTALL TRANSMISSION OIL CLEANER MAGNET

a.
C286291

Install the 2 transmission oil cleaner magnets to the automatic transaxle oil pan sub-assembly as shown in the illustration.


Hide 35106D 7.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.

Install a new automatic transaxle oil pan gasket and automatic transaxle oil pan sub-assembly to the automatic transaxle case sub-assembly with the 18 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

NOTICE:

Completely remove any oil or grease from the contact surfaces of the automatic transaxle case sub-assembly and the automatic transaxle oil pan sub-assembly with the automatic transaxle oil pan gasket before installation.



Hide 8.ADD AUTOMATIC TRANSAXLE FLUID

a.

Pull out the transmission oil level dipstick sub-assembly from the transmission oil filler tube sub-assembly.


b.

Add Toyota Genuine ATF Type T-IV through the transmission oil filler tube sub-assembly.

Automatic Transaxle Fluid (ATF):
Classification Capacity
(Reference)
Toyota Genuine ATF Type T-IV Dry fill 5.6 liters (5.9 US qts, 4.9 Imp. qts)
Drain and refill 2.0 liters (2.1 US qts, 1.8 Imp. qts)



Hide 10.INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEAK

Hide 51442C 11.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

Hide 51405A 12.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 13.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)