Home › Drivetrain › U441E AUTOMATIC TRANSMISSION / TRANSAXLE › TRANSMISSION CONTROL CABLE › 2013.08–2014.03
RM30M0E _52 Drivetrain _017088 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0090625 TRANSMISSION CONTROL CABLE A

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  INSTALLATION  


PROCEDURE

Hide 33829 1.INSTALL NO. 1 TRANSMISSION CONTROL CABLE SUPPORT

HINT:

Perform this procedure only when replacement of the No. 1 transmission control cable support is necessary.


a.
C282053C01
0.802,1.438 1.135,1.219 true 1.406,0.844 1.573,0.75 true 0.646,1.344 0.958,1.5 0.313,0.156 10 false *a 1.615,0.635 1.927,0.792 0.313,0.156 10 false *b
*a Arrow Mark
*b Detent


Install the No. 1 transmission control cable support to the body with the nut.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:
·

Install the No. 1 transmission control cable support so that its arrow mark points to the front of the vehicle.

·

Make sure that the detent of the No. 1 transmission control cable support is pushing against the dash silencer.




Hide 33820B 2.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

NOTICE:

To prevent damage to the transmission control cable assembly and transmission floor shift assembly, connect the automatic transaxle assembly side of the transmission control cable assembly before connecting the transmission floor shift assembly side.


a.

Install the transmission control cable assembly to the body with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.

Install the transmission control cable assembly to the transmission control cable support.


c.
C107759C01
1.333,1.969 1.5,2.146 0.167,0.177 10 true *a 0.781,1.094 0.958,1.271 0.177,0.177 10 true *b
*a P Position
*b N Position


Rotate the transmission control shaft lever counterclockwise until it stops, and then from that position rotate it clockwise by 2 notches to set it to the N position.


d.
C286333C01
0.552,0.875 0.323,0.688 true 0.167,0.573 0.375,0.76 0.208,0.188 10 false *a
*a Paint Mark


Install the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.

NOTICE:

Make sure that the paint mark on the transmission control cable assembly is aligned with the slit in the No. 1 transmission control cable bracket before installing the clip.



e.

Connect the transmission control cable assembly to the transmission control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


f.
C288539C01
2.24,0.906 2.552,0.708 false 1,1.875 1.313,1.677 false 0.854,1.781 1.167,1.938 0.313,0.156 10 false *1 2.594,0.604 2.906,0.76 0.313,0.156 10 false *2
*1 Nut
*2 Lock
V100135

Rotate approximately 180°
V100136

Push in


Rotate the nut of the transmission control cable assembly approximately 180° in the direction shown in the illustration, and while holding the nut, push in the lock.

NOTICE:

Rotating the nut too much will damage the internal spring, and the transmission control cable assembly will not be reusable. Do not turn the nut too far.



g.
C286315C02
0.677,2.292 0.875,2.458 false 2.5,2.281 2.698,2.448 false 0.531,2.177 0.844,2.333 0.313,0.156 10 false *a 2.344,2.188 2.656,2.344 0.313,0.156 10 false *1 0.375,2.427 0.531,2.625 0.156,0.198 10 false A 1.313,2.427 1.469,2.625 0.156,0.198 10 false A
*1 Lock
*a Protrusion
V100135

Push in


Install the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Install the transmission control cable assembly with the protrusion facing upwards.

·

After installation, make sure that the lock is projecting from A as shown in the illustration.

·

Make sure that the transmission control cable assembly is securely locked.




h.
C286313

Confirm that the shift lever is in N, and then connect the end of the transmission control cable assembly to the transmission floor shift assembly.

NOTICE:
·

Securely install the end of the transmission control cable assembly to the transmission floor shift assembly.

·

Install the end of the transmission control cable assembly so that its adjustment lock section is on the driver side.




Hide 58151 4.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator to the body with the 2 bolts and nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17410 5.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 57533B 6.INSTALL FRONT FLOOR CENTER BRACE

Hide 51442C 7.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

Hide 51405A 8.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 9.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 12.INSPECT FOR EXHAUST GAS LEAK