Home › Drivetrain › U441E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT › 2013.08–2016.10
RM30M0E _52 Drivetrain _017088 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0090628 AUTOMATIC TRANSAXLE UNIT G

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  INSPECTION  


PROCEDURE

Hide 35667A 1.INSPECT DIRECT CLUTCH DISC

a.
C286394

Check whether the sliding surfaces of the direct clutch disc, direct clutch clutch plate and the direct clutch flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.




Hide 35677H 2.INSPECT REVERSE CLUTCH DISC

a.
C286922

Check whether the sliding surfaces of the reverse clutch disc, No. 3 clutch plate and the reverse clutch flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.




Hide 35633 3.INSPECT FRONT CLUTCH CLUTCH DISC

a.
C286923

Check whether the sliding surfaces of the front clutch clutch disc, forward clutch clutch plate and the forward clutch flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.




Hide 34633 4.INSPECT 2ND COAST AND OVERDRIVE BRAKE DISC

a.
C203928

Check whether the sliding surfaces of the 2nd coast and overdrive brake disc, 2nd coast and overdrive brake plate and the 2nd coast and overdrive brake flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.




Hide 35682 5.INSPECT 2ND BRAKE BRAKE DISC

a.
C203929

Check whether the sliding surfaces of the 2nd brake brake disc, 2nd brake brake plate and the 2nd brake brake flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.




Hide 35683 6.INSPECT 1ST AND REVERSE BRAKE DISC

a.
C203930

Check whether the sliding surfaces of the 1st and reverse brake disc, 1st and reverse brake plate and the 1st and reverse brake flange are worn or burnt.

If necessary, replace them.

NOTICE:
·

If the lining of the disc is peeling off or discolored, or even if a part of the printed mark is defaced, replace all the discs.

·

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.




Hide 35604 7.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C286397

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

36.04 mm (1.42 in.)


If the free length is shorter than the standard free length, replace the direct clutch return spring sub-assembly.


Hide 34603B 8.INSPECT OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C286399

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

18.99 mm (0.748 in.)


If the free length is shorter than the standard free length, replace the overdrive brake return spring sub-assembly.


Hide 35603A 9.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C286398

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

24.04 mm (0.946 in.)


If the free length is shorter than the standard free length, replace the forward clutch return spring sub-assembly.


Hide 35608L 10.INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C286395

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

15.85 mm (0.624 in.)


If the free length is shorter than the standard free length, replace the 2nd brake piston return spring sub-assembly.


Hide 35068 11.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C286396

Using a vernier caliper, measure the free length of the spring together with the spring seat.

Standard free length:

21.71 mm (0.855 in.)


If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring sub-assembly.


Hide 35606A 12.INSPECT DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
C286400

Make sure that the check ball moves freely by shaking the direct clutch piston sub-assembly.


b.

Check that the valve does not leak by covering the check hole with a finger and applying low pressure compressed air as shown in the illustration.

If necessary, replace the direct clutch piston sub-assembly


Hide 35102 13.INSPECT TRANSAXLE REAR COVER SUB-ASSEMBLY

a.
C286401

Using a caliper gauge, measure the inside diameter of the transaxle rear cover bush.

Standard inside diameter:

13.94 to 13.96 mm (0.5489 to 0.5496 in.)


If necessary, replace the transaxle rear cover sub-assembly.