Home › Drivetrain › U441E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT › 2013.08–2016.10
RM30M0E _52 Drivetrain _017088 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0090628 AUTOMATIC TRANSAXLE UNIT A

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  DISASSEMBLY  


PROCEDURE

Hide 35572A 1.REMOVE TRANSMISSION CONTROL SHAFT LEVER

a.
C286302

Remove the nut, washer and the transmission control shaft lever from the manual valve lever shaft.


Hide 84540 2.REMOVE PARK/NEUTRAL POSITION SWITCH

a.
C286303

Using a screwdriver, pry off the tabs of the lock plate.


b.

Remove the lock nut and the lock plate from the park/neutral position switch.


c.
C286305

Remove the 2 bolts and pull out the park/neutral position switch from the transaxle case.


Hide 89413B 3.REMOVE TRANSMISSION REVOLUTION SENSOR

a.
C286338

Remove the bolt and the transmission revolution sensor from the transaxle case.


b.

Remove the O-ring from the transmission revolution sensor.


Hide 35104V 4.REMOVE BREATHER PLUG HOSE

a.
C286339

Remove the breather plug hose from the No. 1 breather plug.


Hide 35104B 5.REMOVE NO. 1 BREATHER PLUG

a.
C286916

Using a screwdriver, remove the No. 1 breather plug from the transaxle case.


b.

Remove the O-ring from the No. 1 breather plug.


Hide 32921C 6.REMOVE OIL COOLER TUBE UNION

a.
C286340

Remove the 2 oil cooler tube unions from the transaxle case.


b.

Remove the 2 O-rings from the 2 oil cooler tube unions.


Hide 30500 7.SECURE AUTOMATIC TRANSAXLE ASSEMBLY

a.
C244602C01
0.938,1.792 0.615,1.625 false 2.635,1.802 2.927,1.708 false 0.458,1.531 0.667,1.698 0.208,0.167 10 false *a 2.948,1.594 3.156,1.76 0.208,0.167 10 false *a
*a Wooden Block


Place the automatic transaxle assembly on wooden blocks.


Hide 35106D 8.REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.

Remove the drain plug sub-assembly and the gasket from the automatic transaxle oil pan sub-assembly.


b.
C203891

Remove the 18 bolts, automatic transaxle oil pan sub-assembly and the automatic transaxle oil pan gasket from the transaxle case.


Hide 35394 9.REMOVE TRANSMISSION OIL CLEANER MAGNET

a.
C286291

Remove the 2 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.


b.
C283249

Examine the particles in the automatic transaxle oil pan sub-assembly.

i.

Collect any steel chips using the removed transmission oil cleaner magnets.

Carefully inspect the foreign matter and particles in the automatic transaxle oil pan sub-assembly and on the transmission oil cleaner magnets to see the type of wear which might be found in the automatic transaxle assembly.

Steel (magnetic): bearing, gear and clutch plate wear

Brass (non-magnetic): bushing wear



Hide 35330 10.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

a.
C203892

Remove the 3 bolts and the valve body oil strainer assembly from the transmission valve body assembly.


Hide 35410 11.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
C286550C01
2.115,1.302 2.885,1.75 true 2.927,1.656 3.24,1.813 0.313,0.156 10 false *1
*1 Temperature Sensor Clamp


Disengage the temperature sensor clamp and separate the transmission wire from the transmission valve body assembly.


b.

Disengage the 2 clamps, disconnect the 5 connectors and separate the transmission wire from the transmission valve body assembly.


c.
C203894

Remove the 14 bolts and the transmission valve body assembly from the transaxle case.


d.
C286343

Disconnect the manual valve connecting rod from the manual valve lever sub-assembly, then remove the transmission valve body assembly.


Hide 82125J 12.REMOVE TRANSMISSION WIRE

a.
C203904

Remove the bolt.


b.
C203903

Pull out the transmission wire from the transaxle case.


c.
C282693

Remove the O-ring from the transmission wire.


Hide 35148 13.REMOVE NO. 1 GOVERNOR APPLY GASKET

a.
C286345

Remove the No. 1 governor apply gasket from the transaxle case.


Hide 35159 14.REMOVE BRAKE DRUM GASKET

a.
C286375

Remove the brake drum gasket from the transaxle case.


Hide 35251 15.REMOVE CHECK BALL BODY

a.
C286346

Remove the check ball body and the check ball body compression spring from the transaxle case.


Hide 35425A 16.REMOVE C-2 ACCUMULATOR PISTON

a.
C203853

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole and remove the C-2 accumulator piston and the C-2 accumulator piston compression spring.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




b.
C286443

Remove the 2 C-2 accumulator piston O-rings from the C-2 accumulator piston.


Hide 35209 17.REMOVE C-2 ACCUMULATOR SPRING SUB-ASSEMBLY

a.
C286347

Using a screwdriver, remove the accumulator spring hole snap ring and the C-2 accumulator spring sub-assembly from the C-2 accumulator piston.


Hide 35424C 18.REMOVE C-1 ACCUMULATOR PISTON

a.
C203854

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole and remove the C-1 accumulator piston and the C-1 accumulator piston compression spring.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it with your hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




b.
C286442

Remove the 2 C-1 accumulator piston O-rings from the C-1 accumulator piston.


Hide 35206 19.REMOVE C-1 ACCUMULATOR SPRING SUB-ASSEMBLY

a.
C286348

Using a screwdriver, remove the C-1 accumulator spring sub-assembly from the C-1 accumulator piston.


Hide 35427R 20.REMOVE B-1 ACCUMULATOR PISTON

a.
C203855

Remove the No. 2 B-1 accumulator piston compression spring from the B-1 accumulator piston.


b.

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole and remove the B-1 accumulator piston.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it with your hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




c.
C286440

Remove the 2 B-1 accumulator piston O-rings from the B-1 accumulator piston.


Hide 35427P 21.REMOVE B-1 ACCUMULATOR PISTON COMPRESSION SPRING

a.
C286349

Using a screwdriver, remove the B-1 accumulator piston compression spring from the B-1 accumulator piston.


Hide 35111C 22.REMOVE TRANSAXLE HOUSING

a.
C286342

Remove the 16 bolts.


b.

Tap around the circumference of the transaxle housing with a plastic hammer to remove the transaxle housing from the transaxle case.

NOTICE:

The differential gear assembly may be accidentally removed when the transaxle housing is removed.



Hide 35148A 23.REMOVE NO. 2 GOVERNOR APPLY GASKET

a.
C286357

Remove the No. 2 governor apply gasket from the transaxle case.


Hide 24.INSPECT INPUT SHAFT END PLAY

a.
C286350

Using a dial indicator, measure the input shaft end play.

Standard end play:

0.3 to 0.9 mm (0.0119 to 0.0354 in.)



Hide 25.REMOVE OIL PUMP ASSEMBLY

a.
C203857

Remove the 6 bolts and the oil pump assembly from the transaxle case.


Hide 35701 26.REMOVE INPUT SHAFT SUB-ASSEMBLY

a.
C203858

Remove the input shaft sub-assembly from the transaxle case.


Hide 35370A 27.REMOVE STATOR SHAFT THRUST NEEDLE ROLLER BEARING

a.
C203859

Remove the stator shaft thrust needle roller bearing from the input shaft sub-assembly.


Hide 35667A 28.REMOVE DIRECT CLUTCH DISC

a.
C286351

Using a screwdriver, remove the direct clutch flange hole snap ring from the input shaft sub-assembly.


b.

Remove the direct clutch flange, 2 direct clutch discs and the 2 direct clutch clutch plates from the input shaft sub-assembly.


Hide 35604 29.REMOVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C286352N01
1.302,0.833 1.552,0.646 false 1.583,0.552 2.042,0.75 0.458,0.198 10 false SST

Using SST, a press and snap ring expander, remove the direct clutch return spring snap ring from the input shaft sub-assembly.

SST
09387-00020  


b.

Remove the direct clutch return spring sub-assembly from the input shaft sub-assembly.


Hide 35606A 30.REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
C286353

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the input shaft sub-assembly to remove the direct clutch piston sub-assembly from the input shaft sub-assembly.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35606C 31.REMOVE DIRECT CLUTCH PISTON O-RING

a.
C286354

Remove the direct clutch piston O-ring from the direct clutch piston sub-assembly.


b.
C286355

Remove the direct clutch piston O-ring from the input shaft sub-assembly.


Hide 35712A 32.REMOVE INPUT SHAFT OIL SEAL RING

a.
C286356

Remove the 2 input shaft oil seal rings from the input shaft sub-assembly.


Hide 35720J 33.REMOVE PLANETARY GEAR FRONT THRUST NEEDLE ROLLER BEARING

a.
C203860

Remove the planetary gear front thrust needle roller bearing and the planetary gear thrust bearing race from the transaxle case.


Hide 35654B 34.REMOVE DIRECT CLUTCH HUB

a.
C203861

Remove the direct clutch hub from the transaxle case.


Hide 35.REMOVE DIFFERENTIAL GEAR ASSEMBLY

a.
C203862

Remove the differential gear assembly and the differential drive pinion with the counter driven gear from the transaxle case.


Hide 35102 36.REMOVE TRANSAXLE REAR COVER SUB-ASSEMBLY

a.
C288071

Remove the 9 bolts.


b.

Tap around the circumference of the transaxle rear cover sub-assembly with a plastic hammer to remove the transaxle rear cover sub-assembly from the transaxle case.


Hide 34603B 37.REMOVE OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C286344N01
2.125,1.01 2.781,0.479 true 1.896,2.177 2.292,2.115 true 2.813,0.385 3.271,0.583 0.458,0.198 10 false SST 2.333,2.042 2.792,2.24 0.458,0.198 10 false SST

Using SST, a press and screwdriver, remove the overdrive brake return spring hole snap ring from the transaxle rear cover sub-assembly.

SST
09387-00070  


b.

Remove the overdrive brake return spring sub-assembly from the transaxle rear cover sub-assembly.


Hide 34622B 38.REMOVE 2ND COAST AND OVERDRIVE BRAKE PISTON

a.
C203890

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the transaxle rear cover sub-assembly to remove the 2nd coast and overdrive brake piston from the transaxle rear cover sub-assembly.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 34622C 39.REMOVE 2ND COAST AND OVERDRIVE O-RING

a.
C203886

Remove the 2 2nd coast and overdrive O-rings from the 2nd coast and overdrive brake piston.


Hide 35617G 40.REMOVE CLUTCH DRUM OIL SEAL RING

a.
C203887

Remove the 2 clutch drum oil seal rings from the transaxle rear cover sub-assembly.


Hide 35102B 41.REMOVE TRANSAXLE REAR COVER PLUG

a.
C286467

Remove the 4 transaxle rear cover plugs from the transaxle rear cover sub-assembly.


b.

Remove the 4 O-rings from the 4 transaxle rear cover plugs.


Hide 35149B 42.REMOVE TRANSAXLE CASE 2ND BRAKE GASKET

a.
C203864

Remove the 4 transaxle case 2nd brake gaskets from the transaxle case.


Hide 35601D 43.REMOVE FRONT CLUTCH DRUM THRUST NEEDLE ROLLER BEARING

a.
C203865

Remove the front clutch drum thrust needle roller bearing from the intermediate shaft sub-assembly.


Hide 35708G 44.REMOVE INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
C203866

Remove the intermediate shaft sub-assembly from the transaxle case.


Hide 35706G 45.REMOVE SUN GEAR REAR THRUST BEARING

a.
C203867

Remove the front planetary flange rear thrust bearing race, sun gear rear thrust bearing and the sun gear rear thrust bearing race from the intermediate shaft sub-assembly.


Hide 35677H 46.REMOVE REVERSE CLUTCH DISC

a.
C286358

Using a screwdriver, remove the reverse clutch flange hole snap ring from the intermediate shaft sub-assembly.


b.

Remove the 2 reverse clutch flange, 2 reverse clutch discs and the No. 3 clutch plate from the intermediate shaft sub-assembly.


Hide 35633 47.REMOVE FRONT CLUTCH CLUTCH DISC

a.
C286359

Using a screwdriver, remove the forward clutch flange hole snap ring from the clutch drum sub-assembly.


b.

Remove the forward clutch flange, 4 front clutch clutch discs and the 4 forward clutch clutch plates from the clutch drum sub-assembly.


Hide 35668 48.REMOVE NO. 1 CLUTCH BALANCER

a.
C286360N01
1.021,0.74 1.24,0.542 false 1.281,0.448 1.74,0.646 0.458,0.198 10 false SST

Using SST, a press and snap ring expander, remove the clutch balancer snap ring from the intermediate shaft sub-assembly.

SST
09387-00020  


b.

Remove the No. 1 clutch balancer from the intermediate shaft sub-assembly.


Hide 35603A 49.REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C286361

Remove the forward clutch return spring sub-assembly from the intermediate shaft sub-assembly.


Hide 35612B 50.REMOVE FORWARD CLUTCH PISTON

a.
C286362

Install the intermediate shaft sub-assembly onto the transaxle rear cover sub-assembly.


b.

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the transaxle rear cover sub-assembly to remove the forward clutch piston from the intermediate shaft sub-assembly.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35601 51.REMOVE CLUTCH DRUM SUB-ASSEMBLY

a.
C286363

Install the intermediate shaft sub-assembly onto the transaxle rear cover sub-assembly.


b.

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the transaxle rear cover sub-assembly to remove the clutch drum sub-assembly from the intermediate shaft sub-assembly.

NOTICE:
·

Blowing the air may cause the drum to jump out. When removing the drum, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35612C 52.REMOVE FORWARD CLUTCH PISTON O-RING

a.
C286364

Remove the forward clutch piston O-ring from the intermediate shaft sub-assembly.


Hide 35601B 53.REMOVE FRONT CLUTCH DRUM O-RING

a.
C286365

Remove the front clutch drum O-ring from the clutch drum sub-assembly.


Hide 35748C 54.REMOVE INTERMEDIATE SHAFT OIL SEAL RING

a.
C286366

Remove the intermediate shaft oil seal ring from the intermediate shaft sub-assembly.


Hide 34633 55.REMOVE 2ND COAST AND OVERDRIVE BRAKE DISC

a.
C203868

Remove the 2nd coast and overdrive brake flange, 2 2nd coast and overdrive brake discs, 2nd coast and overdrive brake plate and the No. 2 2nd coast and overdrive brake flange from the transaxle case.


Hide 34625E 56.REMOVE 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING

a.
C286548

Using a screwdriver, remove the 2nd coast and overdrive brake flange hole snap ring from the transaxle case.


Hide 35061 57.REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

a.
C203870

Remove the forward clutch hub sub-assembly from the transaxle case.


Hide 35061C 58.REMOVE FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING

a.
C286367

Remove the forward clutch hub thrust needle roller bearing from the forward clutch hub sub-assembly.


Hide 35061B 59.REMOVE FORWARD CLUTCH HUB THRUST BEARING RACE

a.
C286368

Remove the forward clutch hub thrust bearing race from the transaxle case.


Hide 35730 60.REMOVE REAR PLANETARY SUN GEAR ASSEMBLY

a.
C286369

Remove the rear planetary sun gear assembly with the 1-way clutch assembly from the transaxle case.


Hide 35720K 61.REMOVE PLANETARY GEAR REAR THRUST NEEDLE ROLLER BEARING

a.
C286370

Remove the planetary gear rear thrust needle roller bearing from the rear planetary sun gear assembly.


Hide 35790A 62.INSPECT 1-WAY CLUTCH ASSEMBLY

a.
C286371C01
0.813,0.719 1.052,0.917 0.24,0.198 10 false *a 2.552,1.354 2.792,1.552 0.24,0.198 10 false *b
*a Hold
*b Turn
V100135

Lock
V100136

Free


Hold the rear planetary sun gear assembly and turn the 1-way clutch assembly.


b.

Check that the 1-way clutch assembly turns freely clockwise and locks when turned counterclockwise.


Hide 35790A 63.REMOVE 1-WAY CLUTCH ASSEMBLY

a.
C203871

Remove the 1-way clutch assembly and the No. 2 planetary carrier thrust washer from the rear planetary sun gear assembly.


Hide 35737 64.REMOVE PLANETARY CARRIER THRUST WASHER

a.
C203872

Remove the planetary carrier thrust washer from the transaxle case.


Hide 35706 65.REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C203873

Remove the planetary sun gear sub-assembly from the transaxle case.


Hide 35789 66.REMOVE FRONT PLANETARY FLANGE FRONT THRUST BEARING RACE

a.
C286372

Remove the front planetary flange front thrust bearing race from the planetary sun gear sub-assembly.


Hide 35664C 67.REMOVE 2ND BRAKE CYLINDER

a.
C286717C01
2.219,1.24 1.906,0.656 1.906,0.656 2.469,1.031 true 0.417,1.313 0.729,0.667 false 0.74,1.615 0.938,1.51 false 1.604,0.563 2.063,0.76 0.458,0.198 10 false SST 0.74,0.552 0.948,0.75 0.208,0.198 10 false *1 0.958,1.406 1.167,1.604 0.208,0.198 10 false *2
*1 2nd Brake Cylinder Hole Snap Ring
*2 2nd Brake Cylinder


Using SST, a press and screwdriver, remove the 2nd brake cylinder hole snap ring from the transaxle case.

SST
09387-00100  
09950-70010  (09951-07100)


b.

Remove the 2nd brake cylinder from the transaxle case.


Hide 35624E 68.REMOVE 2ND BRAKE PISTON

a.
C286549

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the 2nd brake cylinder to remove the 2nd brake piston from the 2nd brake cylinder.

NOTICE:
·

Blowing the air may cause the piston to jump out. When removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35664D 69.REMOVE 2ND BRAKE CYLINDER O-RING

a.
C203889

Remove the 2 2nd brake cylinder O-rings from the 2nd brake piston.


Hide 35608L 70.REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C286373

Remove the 2nd brake piston return spring sub-assembly from the transaxle case.


Hide 35682 71.REMOVE 2ND BRAKE BRAKE DISC

a.
C286374

Remove the 2 2nd brake brake plates, 2 2nd brake brake discs and the 2nd brake brake flange from the transaxle case.


Hide 34365A 72.REMOVE OUTER RACE RETAINER

a.
C286376

Remove the outer race retainer from the transaxle case.


Hide 35792C 73.INSPECT NO. 2 1-WAY CLUTCH

a.
C286377C01
0,0 0,0 false
V100135

Lock
V100136

Free


Check that the planetary gear assembly turns freely counterclockwise and locks when turned clockwise.


Hide 35792C 74.REMOVE NO. 2 1-WAY CLUTCH

a.
C203874

Remove the No. 2 1-way clutch from the transaxle case.


Hide 35720G 75.REMOVE PLANETARY GEAR ASSEMBLY

a.
C286378

Remove the planetary gear assembly from the transaxle case.


Hide 35683 76.REMOVE 1ST AND REVERSE BRAKE DISC

a.
C288062N01
1.01,0.688 0.479,0.26 0.479,0.26 1.417,0.49 true 0.188,0.167 0.646,0.365 0.458,0.198 10 false SST

Using SST, a press and screwdriver, remove the brake flange hole snap ring from the transaxle case.

SST
09387-00100  
09950-70010  (09951-07100)


b.

Remove the 1st and reverse brake flange, 4 1st and reverse brake discs and the 4 1st and reverse brake plates from the transaxle case.


Hide 35068 77.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C286379

Remove the 1st and reverse brake return spring sub-assembly from the transaxle case.


Hide 35782H 78.REMOVE COUNTER DRIVE GEAR NUT

a.
C286380N01
0.531,2.75 0.396,2.594 0.396,2.594 0.958,2.458 false 0.104,2.5 0.563,2.698 0.458,0.198 10 false SST

Using SST, lift the transaxle case.

SST
09223-15020  
09387-00060  


b.
C286381N01
0.865,0.688 1.188,0.302 true 1.229,0.229 1.688,0.427 0.458,0.198 10 false SST

Using SST and a hammer, release the counter drive gear nut.

SST
09930-00010  

NOTICE:

If a chisel or other tool is used to unstake the planetary ring gear flange, the impact may damage the bearing.



c.
C288063

Fix the counter drive gear with the parking lock pawl.


d.
C286382

Using a 55 mm socket wrench, remove the counter drive gear nut from the planetary ring gear flange.


Hide 35743K 79.REMOVE PLANETARY RING GEAR

a.
C286551N01
1.198,1.135 0.448,0.406 0.448,0.406 1.271,0.708 true 0.156,0.323 0.615,0.521 0.458,0.198 10 false SST

Using SST and a press, remove the planetary ring gear from the transaxle case.

SST
09950-60010  (09951-00420)
09950-70010  (09951-07100)


Hide 35762E 80.REMOVE PLANETARY RING GEAR FLANGE

a.
C286552

Using snap ring pliers, remove the planetary ring gear hole snap ring from the planetary ring gear.


b.

Remove the planetary ring gear flange from the planetary ring gear.


Hide 35782C 81.REMOVE COUNTER DRIVE GEAR

a.
C286383

Install the 3 service bolts to the counter drive gear.

Recommended Service Bolt
Diameter Pitch Length
6 mm (0.236 in.) 1.0 mm (0.0394 in.) 40 to 80 mm (1.58 to 3.14 in.)


b.

Rotate the 3 service bolts and remove the counter drive gear from the transaxle case.


Hide 35623H 82.REMOVE 1ST AND REVERSE BRAKE PISTON

a.
C288064

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the transaxle case to remove the 1st and reverse brake piston from the transaxle case.

NOTICE:
·

Blowing the air may cause the piston to jump out when removing the piston, hold it by hand using a piece of cloth.

·

Do not splash ATF with the compressed air.




Hide 35623J 83.REMOVE 1ST AND REVERSE BRAKE O-RING

a.
C203877

Remove the 2 1st and reverse brake O-rings from the 1st and reverse brake piston.


Hide 35595 84.REMOVE PARKING LOCK PAWL BRACKET

a.
C203878

Remove the 2 bolts and the parking lock pawl bracket from the transaxle case.


Hide 35561 85.REMOVE MANUAL VALVE LEVER SHAFT

a.
C286384

Using a screwdriver, cut off the manual valve lever shaft spacer and remove it from the manual valve lever sub-assembly.


b.
C286385

Using a 3 mm pin punch and hammer, drive out the slotted spring pin from the manual valve lever sub-assembly.


c.

Remove the manual valve lever shaft and the manual valve lever sub-assembly from the transaxle case.


Hide 35501 86.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

a.
C286386

Remove the parking lock rod sub-assembly from the manual valve lever sub-assembly.


Hide 35506F 87.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C286389C01
0.531,0.573 1.833,0.958 false 0.365,0.49 0.677,0.646 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, pry out the manual valve lever shaft oil seal from the transaxle case.


Hide 35409D 88.REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY

a.
C286387

Remove the bolt and the manual detent spring sub-assembly from the transaxle case.


Hide 35557 89.REMOVE PARKING LOCK PAWL

a.
C286553

Remove the parking lock pawl shaft, parking lock pawl torsion spring and the parking lock pawl from the transaxle case.


Hide 35165 90.REMOVE NO. 1 TRANSMISSION CASE PLATE

a.
C203881

Remove the bolt and the No. 1 transmission case plate from the transaxle case.


Hide 35174 91.REMOVE TRANSAXLE HOUSING OIL SEPARATOR

a.
C203882

Remove the 3 bolts and the transaxle housing oil separator from the transaxle housing.


Hide 35195A 92.REMOVE NO. 1 TRANSAXLE APPLY TUBE CLAMP

a.
C203883

Remove the bolt and the No. 1 transaxle apply tube clamp from the transaxle housing.


Hide 35847 93.REMOVE TRANSMISSION LUBE APPLY TUBE

a.
C286392

Remove the transmission lube apply tube from the transaxle housing.

NOTICE:

Do not apply excessive force to the transmission lube apply tube.



Hide 35882A 94.REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C286393

Remove the differential gear lube apply tube from the transaxle housing.

NOTICE:

Do not apply excessive force to the differential gear lube apply tube.



Hide 43420H 95.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C286390

Using a screwdriver and hammer, remove the front drive shaft oil seal LH from the transaxle case.


Hide 43410M 96.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C286391

Using a screwdriver and hammer, remove the front drive shaft oil seal RH from the transaxle housing.


Hide 35104Q 97.REMOVE NO. 1 TRANSAXLE CASE PLUG

a.
C203879

Remove the 2 No. 1 transaxle case plugs from the transaxle housing.


b.

Remove the 2 O-rings from the 2 No. 1 transaxle case plugs.


Hide 35104R 98.REMOVE NO. 2 TRANSAXLE CASE PLUG

a.
C203880

Remove the No. 2 transaxle case plug from the transaxle case.


b.

Remove the O-ring from the No. 2 transaxle case plug.


Hide 41211B 99.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C286458N01
1.573,0.625 0.781,0.75 0.781,0.75 1.052,0.969 false 1.563,0.99 0.781,0.75 false 0.469,0.656 0.927,0.854 0.458,0.198 10 false SST

Using SST and a press, remove the front drive pinion rear tapered roller bearing (inner race) and the counter driven gear from the differential drive pinion.

SST
09950-00020  
09950-60010  (09951-00280)
09950-70010  (09951-07100)


b.
C286459C01
0.417,1.896 0.875,1.573 true 0.698,1.344 0.406,1.906 0.406,1.906 0.76,1.802 true 0.104,1.813 0.563,2.01 0.458,0.198 10 false SST 0.188,1.188 0.396,1.406 0.208,0.219 10 false *a 1.438,1.094 1.656,1.302 0.219,0.208 10 true *b
*a Hold
*b Turn


Using SST, remove the front drive pinion rear tapered roller bearing (outer race) and the drive pinion rear plate washer from the transaxle case.

SST
09387-00041  (09387-01030, 09387-01041)
09387-02010  
09387-02020  

NOTICE:

Apply a small amount of grease to the threads of SST before use.



Hide 41211A 100.REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C286460N01
1.552,1.25 1.073,0.292 true 1.573,0.688 1.063,0.292 1.063,0.292 1.26,0.854 false 0.76,0.208 1.219,0.406 0.458,0.198 10 false SST

Using SST and a press, remove the front drive pinion front tapered roller bearing (inner race) from the differential drive pinion.

SST
09950-00020  
09950-60010  (09951-00280)
09950-70010  (09951-07100)


b.
C286461C01
0.688,1.823 1.177,1.479 true 0.969,1.354 0.677,1.833 0.677,1.833 1.073,1.719 true 0.354,1.75 0.667,1.948 0.313,0.198 10 true SST 0.5,1.073 0.813,1.229 0.313,0.156 10 false *a 1.615,0.865 1.927,1.021 0.313,0.156 10 false *b
*a Hold
*b Turn


Using SST, remove the front drive pinion front tapered roller bearing (outer race) from the transaxle housing.

SST
09316-20011  
09387-00041  (09387-01030, 09387-01041)
09387-02020  

NOTICE:

Apply a small amount of grease to the threads of SST before use.



Hide 41211E 101.REMOVE DIFFERENTIAL DRIVE PINION PLUG

a.
C286462

Using an extension bar and a plastic hammer, remove the differential drive pinion plug from the differential drive pinion.