Home › Drivetrain › U441E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT › 2013.08–2016.10
RM30M0E _52 Drivetrain _017088 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0090628 AUTOMATIC TRANSAXLE UNIT A

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

HINT:

Check bearing position and installation direction.


C288844N01
1.531,0.229 1.688,0.427 0.156,0.198 10 false A 2.531,0.354 2.688,0.552 0.156,0.198 10 false B 1.042,7.396 1.198,7.594 0.156,0.198 10 false C 1.844,7.958 2,8.156 0.156,0.198 10 false D 2.719,8.552 2.875,8.75 0.156,0.198 10 false E 4.031,7.802 4.188,8 0.156,0.198 10 false F 5.979,8.063 6.135,8.26 0.156,0.198 10 false G

Mark Front Race Diameter
Inside / Outside
Thrust Bearing Diameter
Inside / Outside
Rear Race Diameter
Inside / Outside
A - 32.9 mm (1.30 in.) / 48.5 mm (1.91 in.)
or
32.5 mm (1.28 in.) / 48.5 mm (1.91 in.)
-
B - 17.8 mm (0.70 in.) / 30.2 mm (1.19 in.) 20.5 mm (0.81 in.) / 32.6 mm (1.28 in.)
C 19.3 mm (0.76 in.) / 29.0 mm (1.14 in.) - -
D - 41.9 mm (1.65 in.) / 57.5 mm (2.26 in.) -
E 34.95 mm (1.38 in.) / 45.5 mm (1.79 in.) 33.3 mm (1.31 in.) / 46.5 mm (1.83 in.) -
F 19.3 mm (0.76 in.) / 30.6 mm (1.20 in.) 18.1 mm (0.71 in.) / 29.6 mm (1.17 in.) 18.1 mm (0.71 in.) / 28.2 mm (1.11 in.)
G - 43.2 mm (1.70 in.) / 62.0 mm (2.44 in.) -

Hide 41211E 2.INSTALL DIFFERENTIAL DRIVE PINION PLUG

a.
C286481

Using a 10 mm deep socket wrench and a plastic hammer, install a new differential drive pinion plug to the differential drive pinion.

Standard depth:

2.3 to 2.35 mm (0.0906 to 0.0925 in.)



Hide 41211A 3.INSTALL FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C286482N01
1.042,0.729 1.542,0.958 false 0.74,0.635 1.198,0.833 0.458,0.198 10 false SST

Using SST and a press, install a new front drive pinion front tapered roller bearing (inner race) to the differential drive pinion.

SST
09608-04031  


b.
C286483N01
1.479,1.292 0.927,0.51 0.927,0.51 1.563,0.677 true 0.635,0.417 1.094,0.615 0.458,0.198 10 false SST

Using SST and a hammer, install a new front drive pinion front tapered roller bearing (outer race) to the transaxle housing.

SST
09950-60010  (09951-00540)
09950-70010  (09951-07100)


Hide 35783R 4.INSTALL COUNTER DRIVEN GEAR

a.
C286484N01
1.552,1.708 0.698,1.302 0.698,1.302 1.51,0.729 true 0.396,1.219 0.854,1.417 0.458,0.198 10 false SST

Using SST and a press, install the counter driven gear to the differential drive pinion.

SST
09608-04031  
09950-60010  (09951-00280)


Hide 41211B 5.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C286485N01
1.583,1.688 0.719,1.229 0.719,1.229 1.531,0.667 true 0.406,1.146 0.865,1.344 0.458,0.198 10 false SST

Using SST and a press, install the front drive pinion rear tapered roller bearing (inner race) to the differential drive pinion.

SST
09608-04031  
09950-60010  (09951-00280)


b.
C286486N01
1.365,1.51 0.708,0.75 0.708,0.75 1.458,0.979 true 0.417,0.667 0.875,0.865 0.458,0.198 10 false SST

Using SST and a hammer, install the drive pinion rear plate washer and the front drive pinion rear tapered roller bearing (outer race) to the transaxle case.

SST
09950-60010  (09951-00610)
09950-70010  (09951-07150)


Hide 6.INSPECT FRONT DIFFERENTIAL CASE TAPERED ROLLER BEARING PRELOAD

a.
C286918

Coat the differential gear assembly and the tapered roller bearing with Toyota Genuine ATF Type T-IV and install them to the transaxle case.


b.
C286342

Install the transaxle housing to the transaxle case with the 16 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


c.
C286402N01
2.74,1.865 2.656,1.667 true 2.781,1.792 3.24,1.99 0.458,0.198 10 false SST

Using SST and a torque wrench, measure the preload of the front differential case tapered roller bearing.

SST
09564-32011  

Standard preload (at Starting):
New bearing:

0.78 to 1.37 N*m (8.0 to 13.9 kgf*cm, 7.0 to 12.1 in.*lbf)

Used bearing:

0.39 to 0.69 N*m (4.0 to 7.0 kgf*cm, 3.5 to 6.1 in.*lbf)


If the preload is not within the specifications, remove the front differential case rear tapered roller bearing from the transaxle case.

Select a new front differential case rear plate washer in accordance with the following table.

Front Differential Case Rear Plate Washer Thickness:
Part No. Mark Thickness
mm (in.)
Part No. Mark Thickness
mm (in.)
90564-42080 A 1.80 (0.0709) 90564-42092 N 2.26 (0.0890)
90564-42081 B 1.85 (0.0728) 90564-42093 P 2.29 (0.0902)
90564-42082 C 1.90 (0.0748) 90564-42094 Q 2.32 (0.0913)
90564-42083 D 1.95 (0.0768) 90564-42095 R 2.35 (0.0925)
90564-42084 E 2.00 (0.0787) 90564-42096 S 2.40 (0.0945)
90564-42085 F 2.05 (0.0807) 90564-42097 T 2.45 (0.0965)
90564-42086 G 2.08 (0.0819) 90564-42098 U 2.50 (0.0984)
90564-42087 H 2.11 (0.0831) 90564-42099 V 2.55 (0.1004)
90564-42088 J 2.14 (0.0843) 90564-42100 W 2.60 (0.1024)
90564-42089 K 2.17 (0.0854) 90564-42101 X 2.65 (0.1043)
90564-42090 L 2.20 (0.0866) 90564-42102 Y 2.70 (0.1063)
90564-42091 M 2.23 (0.0878) - - -



d.

Remove the 16 bolts and the transaxle housing from the transaxle case.


e.

Remove the differential gear assembly from the transaxle case.


Hide 7.INSPECT FRONT DRIVE PINION TAPERED ROLLER BEARING PRELOAD

a.
C203862

Coat the differential drive pinion assembly, differential gear assembly and the tapered roller bearing with Toyota Genuine ATF Type T-IV and install them to the transaxle case.


b.
C286342

Install the transaxle housing to the transaxle case with the 16 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


c.
C286402N01
2.74,1.865 2.656,1.667 true 2.781,1.792 3.24,1.99 0.458,0.198 10 false SST

Using SST and a torque wrench, measure the preload of the front drive pinion tapered roller bearing.

SST
09564-32011  

Formula:

Measured preload - Front differential case tapered roller bearing preload = Front drive pinion tapered roller bearing preload


Standard preload (at Starting):
New bearing:

0.33 to 0.76 N*m (3.4 to 7.7 kgf*cm, 3.0 to 6.7 in.*lbf)

Used bearing:

0.17 to 0.38 N*m (1.8 to 3.8 kgf*cm, 1.6 to 3.3 in.*lbf)


If the preload is not within the specifications, remove the front drive pinion rear tapered roller bearing from the transaxle case.

Select a new drive pinion rear plate washer in accordance with the following table.

Drive Pinion Rear Plate Washer Thickness:
Part No. Mark Thickness
mm (in.)
Part No. Mark Thickness
mm (in.)
90564-51039 1 1.70 (0.0669) 90564-51052 G 2.17 (0.0854)
90564-51040 2 1.75 (0.0689) 90564-51053 H 2.20 (0.0866)
90564-51041 3 1.80 (0.0709) 90564-51054 K 2.25 (0.0886)
90564-51042 4 1.85 (0.0728) 90564-51055 L 2.30 (0.0906)
90564-51043 5 1.90 (0.0748) 90564-51056 M 2.35 (0.0925)
90564-51044 6 1.93 (0.0760) 90564-51057 N 2.40 (0.0945)
90564-51045 7 1.96 (0.0772) 90564-51058 P 2.45 (0.0965)
90564-51046 A 1.99 (0.0783) 90564-51059 Q 2.50 (0.0984)
90564-51047 B 2.02 (0.0795) 90564-51060 R 2.55 (0.1004)
90564-51048 C 2.05 (0.0807) 90564-51061 S 2.60 (0.1024)
90564-51049 D 2.08 (0.0819) 90564-51062 U 2.65 (0.1043)
90564-51050 E 2.11 (0.0831) 90564-51063 W 2.70 (0.1063)
90564-51051 F 2.14 (0.0843) - - -



d.

Remove the 16 bolts and the transaxle housing from the transaxle case.


e.

Remove the differential drive pinion assembly and the differential gear assembly from the transaxle case.


Hide 35104Q 8.INSTALL NO. 1 TRANSAXLE CASE PLUG

a.
C203879

Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the 2 No. 1 transaxle case plugs.

NOTICE:

Do not twist the O-rings.



b.

Install the 2 No. 1 transaxle case plugs to the transaxle housing.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)

NOTICE:

Do not damage the O-rings.



Hide 35104R 9.INSTALL NO. 2 TRANSAXLE CASE PLUG

a.
C203880

Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it to the No. 2 transaxle case plug.

NOTICE:

Do not twist the O-ring.



b.

Install the No. 2 transaxle case plug to the transaxle case.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)

NOTICE:

Do not damage the O-ring.



Hide 43420H 10.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C286405N01
2.271,3.031 2.49,2.167 true 2.135,3.042 2.594,3.24 0.458,0.198 10 false SST

Using SST and a hammer, tap in a new front drive shaft oil seal LH to the transaxle case.

SST
09316-60011  (09316-00011)

Standard depth:

2.6 to 3.6 mm (0.103 to 0.141 in.)



b.

Coat the lip of the front drive shaft oil seal LH with MP grease.


Hide 43410M 11.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C286406N01
0.771,1.948 0.427,1.323 0.427,1.323 0.906,1.063 true 0.427,1.313 0.781,1.625 false 0.135,1.229 0.594,1.427 0.458,0.198 10 false SST

Using SST and a hammer, tap in a new front drive shaft oil seal RH to the transaxle housing.

SST
09630-24014  (09620-24051)
09950-60010  (09951-00410, 09951-00530, 09952-06010)
09950-70010  (09951-07100)

Standard depth:

2.6 to 3.6 mm (0.103 to 0.141 in.)



b.

Coat the lip of the front drive shaft oil seal RH with MP grease.


Hide 35882A 12.INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C286393

Install the differential gear lube apply tube to the transaxle housing.

NOTICE:

Do not apply excessive force to the differential gear lube apply tube.



Hide 35847 13.INSTALL TRANSMISSION LUBE APPLY TUBE

a.
C286392

Install the transmission lube apply tube to the transaxle housing.

NOTICE:

Do not apply excessive force to the transmission lube apply tube.



Hide 35195A 14.INSTALL NO. 1 TRANSAXLE APPLY TUBE CLAMP

a.
C203883

Install the No. 1 transaxle apply tube clamp to the transaxle housing with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 35174 15.INSTALL TRANSAXLE HOUSING OIL SEPARATOR

a.
C203882

Install the transaxle housing oil separator to the transaxle housing with the 3 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 35165 16.INSTALL NO. 1 TRANSMISSION CASE PLATE

a.
C203881

Install the No. 1 transmission case plate to the transaxle case with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35557 17.INSTALL PARKING LOCK PAWL

a.
C286553

Install the parking lock pawl and the parking lock pawl torsion spring to the transaxle case with the parking lock pawl shaft.

NOTICE:

Check that the parking lock pawl moves smoothly.



Hide 35409D 18.INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY

a.
C286387

Install the manual detent spring sub-assembly to the transaxle case with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35506F 19.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C286407N01
1.479,0.813 0.49,0.479 0.49,0.479 1.542,0.667 true 0.188,0.385 0.646,0.583 0.458,0.198 10 false SST

Using SST and a hammer, install a new manual valve lever shaft oil seal to the transaxle case.

SST
09950-60010  (09951-00210)
09950-70010  (09951-07100)

Standard depth:

0.75 to 1.25 mm (0.0296 to 0.0492 in.)



b.

Coat the lip of the manual valve lever shaft oil seal with MP grease.


Hide 35501 20.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

a.
C286386

Install the parking lock rod sub-assembly to the manual valve lever sub-assembly.


Hide 35561 21.INSTALL MANUAL VALVE LEVER SHAFT

a.
C286409

Install a new manual valve lever shaft spacer to the manual valve lever sub-assembly.


b.
C286385

Install the manual valve lever shaft and the manual valve lever sub-assembly to the transaxle case.

NOTICE:

Do not damage the lip of the manual valve lever shaft oil seal.



c.

Using a 3 mm pin punch and hammer, drive in the slotted spring pin to the manual valve lever sub-assembly.


d.
C282805

Turn the manual valve lever shaft spacer and the manual valve lever shaft to align the small hole for locating the staking position on the manual valve lever shaft spacer with the staking position mark on the manual valve lever shaft.


e.

Using a punch, stake the manual valve lever shaft spacer through the small hole.


f.

Check that the manual valve lever shaft spacer does not turn.


Hide 35595 22.INSTALL PARKING LOCK PAWL BRACKET

a.
C203878

Install the parking lock pawl bracket to the transaxle case with the 2 bolts.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 35623J 23.INSTALL 1ST AND REVERSE BRAKE O-RING

a.
C203877

Coat 2 new 1st and reverse brake O-rings with Toyota Genuine ATF Type T-IV, and install them to the 1st and reverse brake piston.

NOTICE:

Do not twist the O-rings.



Hide 35623H 24.INSTALL 1ST AND REVERSE BRAKE PISTON

a.
C286410

Install the 1st and reverse brake piston to the transaxle case.

NOTICE:

Do not damage the O-rings.



Hide 35068 25.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C286379

Install the 1st and reverse brake return spring sub-assembly to the transaxle case.


Hide 35683 26.INSTALL 1ST AND REVERSE BRAKE DISC

a.
C286411C01
2.073,0.833 2.51,0.833 true 1.531,1.021 0.917,1.073 0.917,1.073 1.531,0.906 false 1.542,1.25 0.927,1.073 0.927,1.073 1.531,1.135 false 2.073,1.188 2.531,1.115 2.531,1.115 2.083,1.073 true 2.083,1.292 2.531,1.115 2.531,1.115 2.073,0.958 true 0.74,0.979 1.052,1.135 0.313,0.156 10 false *1 2.563,0.74 2.875,0.896 0.313,0.156 10 false *2 2.573,1.031 2.885,1.188 0.313,0.156 10 false *3
*1 1st and Reverse Brake Disc
*2 1st and Reverse Brake Flange
*3 1st and Reverse Brake Plate


Install the 4 1st and reverse brake plates, 4 1st and reverse brake discs and the 1st and reverse brake flange to the transaxle case.

NOTICE:

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



b.
C288062N01
1.01,0.688 0.479,0.26 0.479,0.26 1.417,0.49 true 0.188,0.167 0.646,0.365 0.458,0.198 10 false SST

Using SST, a press and screwdriver, install the brake flange hole snap ring to the transaxle case.

SST
09387-00100  
09950-70010  (09951-07100)

NOTICE:

Make sure that the snap ring is installed in the groove of the transaxle case correctly.



Hide 35679 27.INSPECT PISTON STROKE OF 1ST AND REVERSE BRAKE

a.
C286413N01
1.281,1.042 0.552,0.49 true 0.25,0.406 0.708,0.604 0.458,0.198 10 false SST

Using SST and a dial indicator, measure the 1st and reverse brake piston stroke while applying and releasing compressed air (392 to 785 kPa (4.0 to 8.0 kgf/cm2, 57 to 113 psi)).

SST
09350-36010  (09350-06110)

Standard piston stroke:

0.791 to 1.489 mm (0.0312 to 0.0586 in.)


If the piston stroke is outside the specifications, inspect the 1st and reverse brake discs, 1st and reverse brake plates and the 1st and reverse brake flange.


Hide 35782C 28.INSTALL COUNTER DRIVE GEAR

a.
C286414N01
0.719,2.896 0.385,3.052 0.385,3.052 0.542,3.26 false 1.313,1.51 1.104,1.083 1.104,1.083 1.594,1.198 false 0.083,2.969 0.542,3.167 0.458,0.198 10 false SST 0.802,1 1.26,1.198 0.458,0.198 10 false SST

Using SST and a press, install the counter drive gear to the transaxle case.

SST
09223-15030  
09387-00060  
09950-60020  (09951-00710)
09950-70010  (09951-07100)

NOTICE:

Do not apply excessive force to the transaxle case.



Hide 35762E 29.INSTALL PLANETARY RING GEAR FLANGE

a.
C286552

Install a new planetary ring gear flange to the planetary ring gear.


b.

Using snap ring pliers, install the planetary ring gear hole snap ring to the planetary ring gear.


Hide 35743K 30.INSTALL PLANETARY RING GEAR

a.
C286415N01
0.719,2.927 0.375,3.104 0.375,3.104 0.542,3.26 false 1.594,1.198 1.177,1.031 1.177,1.031 1.396,1.438 false 0.885,0.948 1.344,1.146 0.458,0.198 10 false SST 0.083,3.031 0.542,3.229 0.458,0.198 10 false SST

Using SST and a press, install the planetary ring gear to the transaxle case.

SST
09223-15030  
09387-00060  
09950-60010  (09951-00500)
09950-70010  (09951-07100)


Hide 35782H 31.INSTALL COUNTER DRIVE GEAR NUT

a.
C288063

Fix the counter drive gear with the parking lock pawl.


b.
C286382

Using a 55 mm socket wrench, temporarily tighten a new counter drive gear nut to the planetary ring gear flange.

HINT:

Torque: 100 N*m (1020 kgf*cm, 74 ft.*lbf)



c.
C286416

Tighten the counter drive gear nut so that the preload is within the specified range when the counter drive gear is rotated at 100 rpm.

Standard preload:

0.05 to 0.35 N*m (0.6 to 3.5 kgf*cm, 0.5 to 3.0 in.*lbf)


HINT:

Tighten the counter drive gear nut gradually so that the preload is within the specifications.



d.
C286380N01
0.531,2.75 0.396,2.594 0.396,2.594 0.958,2.458 false 0.104,2.5 0.563,2.698 0.458,0.198 10 false SST

Using SST, lift the transaxle case.

SST
09223-15020  
09387-00060  


e.
C286417

Using a chisel and hammer, stake the planetary ring gear flange.

NOTICE:

When staking the planetary ring gear flange, do not damage the counter drive gear nut.



Hide 35720G 32.INSTALL PLANETARY GEAR ASSEMBLY

a.
C286378

Install the planetary gear assembly to the transaxle case.


Hide 35792C 33.INSTALL NO. 2 1-WAY CLUTCH

a.
C203874

Install the No. 2 1-way clutch to the transaxle case.


Hide 35792C 34.INSPECT NO. 2 1-WAY CLUTCH

a.
C286377C01
0,0 0,0 false
V100135

Lock
V100136

Free


Check that the planetary gear assembly turns freely counterclockwise and locks when turned clockwise.

If the No. 2 1-way clutch does not operate normally, replace it.


Hide 34365A 35.INSTALL OUTER RACE RETAINER

a.
C286376

Install the outer race retainer in the place shown in the illustration (the space between the No. 2 1-way clutch outer race and transaxle case). Push the outer race retainer in until it makes a click sound.


Hide 35682 36.INSTALL 2ND BRAKE BRAKE DISC

a.
C286418C01
2.094,1.323 2.573,1.323 false 1.052,1.198 0.729,0.885 0.729,0.885 1.052,1.031 false 2.094,0.948 2.583,1.01 2.583,1.01 2.104,1.115 true 0.573,0.802 0.885,0.958 0.313,0.156 10 false *1 2.656,1.25 2.969,1.406 0.313,0.156 10 false *2 2.656,0.938 2.969,1.094 0.313,0.156 10 false *3
*1 2nd Brake Brake Disc
*2 2nd Brake Brake Flange
*3 2nd Brake Brake Plate


Install the 2nd brake brake flange, 2 2nd brake brake discs and the 2 2nd brake brake plates to the transaxle case.

NOTICE:

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



Hide 35608L 37.INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C286373

Install the 2nd brake piston return spring sub-assembly to the transaxle case.


Hide 35664D 38.INSTALL 2ND BRAKE CYLINDER O-RING

a.
C203889

Coat 2 new 2nd brake cylinder O-rings with Toyota Genuine ATF Type T-IV, and install them to the 2nd brake piston.

NOTICE:

Do not twist the O-rings.



Hide 35624E 39.INSTALL 2ND BRAKE PISTON

a.
C286554

Install the 2nd brake piston to the 2nd brake cylinder.

NOTICE:

Do not damage the O-rings.



Hide 35664C 40.INSTALL 2ND BRAKE CYLINDER

a.
C286419C01
0.552,1.979 0.844,1.906 false 0.385,1.875 0.656,2.073 0.271,0.198 10 false *a
*a Projection


Install the 2nd brake cylinder to the transaxle case as shown in the illustration.

HINT:

Install the 2nd brake cylinder so that the projection is aligned with the groove on the lower side of the transaxle case.



b.
C286717C01
2.219,1.24 1.906,0.656 1.906,0.656 2.469,1.031 true 0.417,1.313 0.729,0.667 false 0.74,1.615 0.938,1.51 false 1.604,0.563 2.063,0.76 0.458,0.198 10 false SST 0.74,0.552 0.948,0.75 0.208,0.198 10 false *1 0.958,1.406 1.167,1.604 0.208,0.198 10 false *2
*1 2nd Brake Cylinder Hole Snap Ring
*2 2nd Brake Cylinder


Using SST, a press and screwdriver, install the 2nd brake cylinder hole snap ring to the transaxle case.

SST
09387-00100  
09950-70010  (09951-07100)

NOTICE:

Make sure that the snap ring is installed in the groove of the transaxle case correctly.



Hide 34625E 41.INSTALL 2ND COAST AND OVERDRIVE BRAKE FLANGE HOLE SNAP RING

a.
C286548

Using a screwdriver, install the 2nd coast and overdrive flange hole snap ring to the transaxle case.

NOTICE:

Make sure that the snap ring is installed in the groove of the transaxle case correctly.



Hide 35789 42.INSTALL FRONT PLANETARY FLANGE FRONT THRUST BEARING RACE

a.
C286372

Coat the front planetary flange front thrust bearing race with Toyota Genuine ATF Type T-IV, and install it to the planetary sun gear sub-assembly.


Hide 35706 43.INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C203873

Install the planetary sun gear sub-assembly to the transaxle case.


Hide 35737 44.INSTALL PLANETARY CARRIER THRUST WASHER

a.
C203872

Coat the planetary carrier thrust washer with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 35790A 45.INSTALL 1-WAY CLUTCH ASSEMBLY

a.
C203871

Coat the No. 2 planetary carrier thrust washer with Toyota Genuine ATF Type T-IV, and install it to the rear planetary sun gear assembly.


b.

Install the 1-way clutch assembly to the rear planetary sun gear assembly.


Hide 35790A 46.INSPECT 1-WAY CLUTCH ASSEMBLY

a.
C286371C01
0.813,0.719 1.052,0.917 0.24,0.198 10 false *a 2.552,1.354 2.792,1.552 0.24,0.198 10 false *b
*a Hold
*b Turn
V100135

Lock
V100136

Free


Hold the rear planetary sun gear assembly and turn the 1-way clutch assembly.


b.

Check that the 1-way clutch assembly turns freely clockwise and locks when turned counterclockwise.

If the 1-way clutch assembly does not operate normally, replace it.


Hide 35720K 47.INSTALL PLANETARY GEAR REAR THRUST NEEDLE ROLLER BEARING

a.
C286370

Coat the planetary gear rear thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it to the rear planetary sun gear assembly.


Hide 35730 48.INSTALL REAR PLANETARY SUN GEAR ASSEMBLY

a.
C286369

Install the rear planetary sun gear assembly with the 1-way clutch assembly to the transaxle case.


Hide 35061B 49.INSTALL FORWARD CLUTCH HUB THRUST BEARING RACE

a.
C286368

Coat the forward clutch hub thrust bearing race with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 35061C 50.INSTALL FORWARD CLUTCH HUB THRUST NEEDLE ROLLER BEARING

a.
C286367

Coat the forward clutch hub thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it to the forward clutch hub sub-assembly.


Hide 35061 51.INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY

a.
C203870

Install the forward clutch hub sub-assembly to the transaxle case.


Hide 35748C 52.INSTALL INTERMEDIATE SHAFT OIL SEAL RING

a.
C286366

Coat a new intermediate shaft oil seal ring with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft sub-assembly.

NOTICE:

Do not expand the oil seal ring excessively.



Hide 35601B 53.INSTALL FRONT CLUTCH DRUM O-RING

a.
C286365

Coat a new front clutch drum O-ring with Toyota Genuine ATF Type T-IV, and install it to the clutch drum sub-assembly.

NOTICE:

Do not twist the O-ring.



Hide 35612C 54.INSTALL FORWARD CLUTCH PISTON O-RING

a.
C286364

Coat a new forward clutch piston O-ring with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft sub-assembly.

NOTICE:

Do not twist the O-ring.



Hide 35601 55.INSTALL CLUTCH DRUM SUB-ASSEMBLY

a.
C286421

Coat the clutch drum sub-assembly with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft sub-assembly.

NOTICE:

Do not damage the O-ring.



Hide 35612B 56.INSTALL FORWARD CLUTCH PISTON

a.
C286422

Coat the forward clutch piston with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft sub-assembly.

NOTICE:

Do not damage the O-ring.



Hide 35603A 57.INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C286361

Install the forward clutch return spring sub-assembly to the intermediate shaft sub-assembly.


Hide 35668 58.INSTALL NO. 1 CLUTCH BALANCER

a.
C286360N01
1.021,0.74 1.24,0.542 false 1.281,0.448 1.74,0.646 0.458,0.198 10 false SST

Coat the No. 1 clutch balancer with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft sub-assembly.


b.

Using SST, a press and snap ring expander, install the clutch balancer snap ring to the intermediate shaft sub-assembly.

SST
09387-00020  


Hide 35633 59.INSTALL FRONT CLUTCH CLUTCH DISC

a.
C286423C01
2.188,0.417 2.646,0.417 true 1.844,0.74 1.563,0.573 1.563,0.573 1.854,0.458 false 1.844,0.656 1.573,0.573 1.573,0.573 1.833,0.563 false 2.198,0.688 2.656,0.635 2.656,0.635 2.188,0.594 true 2.188,0.781 2.667,0.646 2.667,0.646 2.188,0.5 true 1.406,0.49 1.719,0.646 0.313,0.156 10 false *1 2.708,0.313 3.021,0.469 0.313,0.156 10 false *2 2.719,0.552 3.031,0.708 0.313,0.156 10 false *3
*1 Front Clutch Clutch Disc
*2 Forward Clutch Flange
*3 Forward Clutch Clutch Plate


Install the 4 forward clutch clutch plates, 4 front clutch clutch discs and the forward clutch flange to the clutch drum sub-assembly.

NOTICE:

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



b.

Using a screwdriver, install the forward clutch flange hole snap ring to the clutch drum sub-assembly.


Hide 35677H 60.INSTALL REVERSE CLUTCH DISC

a.
C286424C01
2.198,0.469 2.719,0.469 true 1.708,0.781 1.438,0.677 1.438,0.677 1.698,0.583 false 2.198,0.677 2.719,0.677 true 2.198,0.885 2.719,0.885 true 1.271,0.594 1.583,0.75 0.313,0.156 10 false *1 2.771,0.385 3.083,0.542 0.313,0.156 10 false *2 2.771,0.583 3.083,0.74 0.313,0.156 10 false *3 2.771,0.802 3.083,0.958 0.313,0.156 10 false *4
*1 Reverse Clutch Disc
*2 Reverse Clutch Flange
*3 No. 3 Clutch Plate
*4 Reverse Clutch Flange 3.0 mm (0.118 in.)


Install the 2 reverse clutch flanges, 2 reverse clutch discs and the No. 3 clutch plate to the intermediate shaft sub-assembly.

NOTICE:

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



b.

Using a screwdriver, install the reverse clutch flange hole snap ring to the intermediate shaft sub-assembly.


Hide 35649 61.INSPECT PACK CLEARANCE OF REVERSE CLUTCH

a.
C286425

Install the intermediate shaft sub-assembly onto the transaxle rear cover sub-assembly.


b.

Using a dial indicator, measure the clearance of the reverse clutch while applying and releasing compressed air (400 kPa (4.1 kgf/cm2, 58 psi)).

Standard clearance:

0.4 to 1.0 mm (0.0158 to 0.0393 in.)


If the clearance is outside the specifications, select a new reverse clutch flange.

Reverse Clutch Flange Thickness:
Part No. Mark Thickness
mm (in.)
35649-52010 1 3.0 (0.118)
35649-52060 2 3.2 (0.126)
35649-52070 3 3.4 (0.134)
35649-52080 4 3.6 (0.142)



Hide 35635 62.INSPECT PACK CLEARANCE OF FORWARD CLUTCH

a.
C286426N01
1.448,0.635 1.99,1.063 true 1.156,0.531 1.615,0.729 0.458,0.198 10 false SST

Install the intermediate shaft sub-assembly onto the transaxle rear cover sub-assembly.


b.

Using SST and a dial indicator, measure the clearance of the forward clutch while applying and releasing compressed air (400 kPa (4.1 kgf/cm2, 58 psi)).

SST
09350-36010  (09350-06120)

Standard clearance:

1.3 to 1.5 mm (0.0512 to 0.0590 in.)


If the clearance is outside the specifications, select a new forward clutch flange.

Forward Clutch Flange Thickness:
Part No. Mark Thickness
mm (in.)
35635-52010 1 3.0 (0.118)
35635-52090 5 3.1 (0.122)
35635-52020 2 3.2 (0.126)
35635-52100 6 3.3 (0.130)
35635-52030 3 3.4 (0.134)
35635-52110 7 3.5 (0.138)
35635-52040 4 3.6 (0.142)



Hide 35706G 63.INSTALL SUN GEAR REAR THRUST BEARING

a.
C203867

Coat the sun gear rear thrust bearing race, sun gear rear thrust bearing and the front planetary flange rear thrust bearing race with Toyota Genuine ATF Type T-IV, and install them to the intermediate shaft sub-assembly.


Hide 35708G 64.INSTALL INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
C203866

Install the intermediate shaft sub-assembly to the transaxle case.


Hide 34633 65.INSTALL 2ND COAST AND OVERDRIVE BRAKE DISC

a.
C286427C01
1.49,0.896 0.698,1.135 0.698,1.135 1.5,0.74 true 2.385,0.823 2.979,0.823 true 2.385,0.646 2.979,0.646 true 2.385,1.021 2.979,1.021 true 0.542,1.052 0.854,1.25 0.313,0.198 10 false *1 3.031,0.552 3.344,0.75 0.313,0.198 10 false *2 3.031,0.719 3.344,0.917 0.313,0.198 10 false *3 3.031,0.927 3.344,1.125 0.313,0.198 10 false *4
*1 2nd Coast and Overdrive Brake Disc
*2 2nd Coast and Overdrive Brake Flange
*3 2nd Coast and Overdrive Brake Plate
*4 No. 2 2nd Coast and Overdrive Brake Flange


Install the No. 2 2nd coast and overdrive brake flange, 2 2nd coast and overdrive brake discs, 2nd coast and overdrive brake plate and the 2nd coast and overdrive brake flange to the transaxle case.

NOTICE:

Before assembling new discs, soak them in Toyota Genuine ATF Type T-IV for at least 15 minutes.



Hide 35102B 66.INSTALL TRANSAXLE REAR COVER PLUG

a.
C286467

Coat 4 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the 4 transaxle rear cover plugs.

NOTICE:

Do not twist the O-rings.



b.

Install the 4 transaxle rear cover plugs to the transaxle rear cover sub-assembly.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)

NOTICE:

Do not damage the O-rings.



Hide 35617G 67.INSTALL CLUTCH DRUM OIL SEAL RING

a.
C203887

Coat 2 new clutch drum oil seal rings with Toyota Genuine ATF Type T-IV, and install them to the transaxle rear cover sub-assembly.

NOTICE:

Do not expand the oil seal ring excessively.



Hide 34622C 68.INSTALL 2ND COAST AND OVERDRIVE O-RING

a.
C203886

Coat 2 new 2nd coast and overdrive O-rings with Toyota Genuine ATF Type T-IV, and install them to the 2nd coast overdrive brake piston.

NOTICE:

Do not twist the O-rings.



Hide 34622B 69.INSTALL 2ND COAST AND OVERDRIVE BRAKE PISTON

a.
C286429

Install the 2nd coast and overdrive brake piston to the transaxle rear cover sub-assembly.

NOTICE:

Do not damage the O-rings.



Hide 34603B 70.INSTALL OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C286344N01
2.125,1.01 2.781,0.479 true 1.896,2.177 2.292,2.115 true 2.813,0.385 3.271,0.583 0.458,0.198 10 false SST 2.333,2.042 2.792,2.24 0.458,0.198 10 false SST

Install the overdrive brake return spring sub-assembly to the transaxle rear cover sub-assembly.


b.

Using SST, a press and screwdriver, install the overdrive brake return spring hole snap ring to the transaxle rear cover sub-assembly.

SST
09387-00070  


Hide 34625D 71.INSPECT PISTON CLEARANCE OF 2ND COAST AND OVERDRIVE BRAKE

a.
C286430E01
0.271,0.385 0.427,0.583 0.156,0.198 10 false A

Using a straightedge and vernier caliper, measure dimension A from the transaxle case end surface to the 2nd coast and overdrive brake flange.


b.
C286431E01
3.104,0.667 3.26,0.865 0.156,0.198 10 false B

Using a straightedge and vernier caliper, measure dimension B from the 2nd coast and overdrive brake piston to the edge surface of the transaxle rear cover sub-assembly.


c.

Calculate the clearance from the measured dimensions A and B.

Standard clearance:

0.65 to 1.05 mm (0.0256 to 0.0413 in.)


HINT:

Piston clearance = Dimension A - Dimension B


If the clearance is outside the specifications, select a new 2nd coast and overdrive brake flange.

2nd Coast and Overdrive Brake Flange Thickness:
Part No. Mark Thickness
mm (in.)
34625-52010 1 1.8 (0.0709)
34625-52020 2 2.0 (0.0787)
34625-52030 3 2.2 (0.0866)
34625-52040 4 2.4 (0.0945)
34625-52050 5 2.6 (0.1024)



Hide 35149B 72.INSTALL TRANSAXLE CASE 2ND BRAKE GASKET

a.
C203864

Coat 4 new transaxle case 2nd brake gaskets with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.


Hide 35601D 73.INSTALL FRONT CLUTCH DRUM THRUST NEEDLE ROLLER BEARING

a.
C203865

Coat the front clutch drum thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it to the intermediate shaft sub-assembly.


Hide 35102 74.INSTALL TRANSAXLE REAR COVER SUB-ASSEMBLY

a.

Clean and degrease the contact surfaces of the transaxle rear cover sub-assembly and the transaxle case.


b.
C286432C01
0.427,0.927 0.854,0.927 true 0.219,0.823 0.531,1.021 0.313,0.198 10 false *a
*a Seal Packing
(Seal Diameter: 1.2 mm (0.0472 in.))


Apply a continuous bead of seal packing (Diameter 1.2 mm (0.0472 in.)) to the transaxle rear cover sub-assembly.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.



c.
C288071

Install the transaxle rear cover sub-assembly to the transaxle case with the 9 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 75.INSTALL DIFFERENTIAL GEAR ASSEMBLY

a.
C203862

Install the differential drive pinion assembly and the differential gear assembly to the transaxle case.


Hide 35654B 76.INSTALL DIRECT CLUTCH HUB

a.
C203861

Install the direct clutch hub to the transaxle case.


Hide 35720J 77.INSTALL PLANETARY GEAR FRONT THRUST NEEDLE ROLLER BEARING

a.
C203860

Coat the planetary gear thrust bearing race and the planetary gear front thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install them to the transaxle case.


Hide 35712A 78.INSTALL INPUT SHAFT OIL SEAL RING

a.
C286356

Coat 2 new input shaft oil seal rings with Toyota Genuine ATF Type T-IV, and install them to the input shaft sub-assembly.

NOTICE:

Do not expand the oil seal ring excessively.



Hide 35606C 79.INSTALL DIRECT CLUTCH PISTON O-RING

a.
C286355

Coat a new direct clutch piston O-ring with Toyota Genuine ATF Type T-IV, and install it to the input shaft sub-assembly.

NOTICE:

Do not twist the O-ring.



b.
C286354

Coat a new direct clutch piston O-ring with Toyota Genuine ATF Type T-IV, and install it to the direct clutch piston sub-assembly.

NOTICE:

Do not twist the O-ring.



Hide 35606A 80.INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
C286433

Install the direct clutch piston sub-assembly to the input shaft sub-assembly.

NOTICE:

Do not damage the O-rings.



Hide 35604 81.INSTALL DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
C286352N01
1.302,0.833 1.552,0.646 false 1.583,0.552 2.042,0.75 0.458,0.198 10 false SST

Install the direct clutch return spring sub-assembly to the input shaft sub-assembly.


b.

Using SST, a press and snap ring expander, install the direct clutch return spring snap ring to the input shaft sub-assembly.

SST
09387-00020  


Hide 35667A 82.INSTALL DIRECT CLUTCH DISC

a.
C286434C01
2.135,0.865 2.625,0.563 true 1.417,0.969 1.104,0.708 1.104,0.708 1.417,1.135 true 2.146,1.052 2.625,1.156 2.625,1.156 2.135,1.229 true 2.667,0.458 2.979,0.615 0.313,0.156 10 false *1 0.917,0.583 1.083,0.771 0.167,0.188 10 true *2 2.688,1.073 3,1.229 0.313,0.156 10 false *3
*1 Direct Clutch Flange
*2 Direct Clutch Disc
*3 Direct Clutch Clutch Plate


Install the 2 direct clutch clutch plates, 2 direct clutch discs and the direct clutch flange to the input shaft sub-assembly.


b.

Using a screwdriver, install the direct clutch flange hole snap ring to the input shaft sub-assembly.


Hide 35675C 83.INSPECT PISTON STROKE OF DIRECT CLUTCH

a.
C286435

Install the input shaft sub-assembly onto the oil pump assembly.


b.

Using a dial indicator, measure the direct clutch piston stroke while applying and releasing compressed air (400 kPa (4.1 kgf/cm2, 58 psi)).

Standard piston stroke:

0.4 to 0.7 mm (0.0158 to 0.0275 in.)


If the piston stroke is outside the specifications, select a new direct clutch flange.

Direct Clutch Flange Thickness:
Part No. Mark Thickness
mm (in.)
35675-52010 1 3.0 (0.118)
35675-52020 2 3.2 (0.126)
35675-52030 3 3.4 (0.134)



Hide 35370A 84.INSTALL STATOR SHAFT THRUST NEEDLE ROLLER BEARING

a.
C203859

Coat the stator shaft thrust needle roller bearing with Toyota Genuine ATF Type T-IV, and install it to the input shaft sub-assembly.


Hide 35701 85.INSTALL INPUT SHAFT SUB-ASSEMBLY

a.
C203858

Install the input shaft sub-assembly to the transaxle case.


Hide 86.INSTALL OIL PUMP ASSEMBLY

a.
C203857

Install the oil pump assembly to the transaxle case with the 6 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 87.INSPECT INPUT SHAFT

a.
C286436

Make sure that the input shaft turns smoothly.


Hide 88.INSPECT INPUT SHAFT END PLAY

a.
C286350

Using a dial indicator, measure the input shaft end play.

Standard end play:

0.3 to 0.9 mm (0.0119 to 0.0354 in.)


If the end play is not as specified, select and replace the stator shaft thrust needle roller bearing.

Stator Shaft Thrust Needle Roller Bearing Thickness:
Part No. Thickness
mm (in.)
90374-32008 3.62 (0.143)
90374-32007 4.21 (0.166)



Hide 35148A 89.INSTALL NO. 2 GOVERNOR APPLY GASKET

a.
C286357

Coat a new No. 2 governor apply gasket with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 35111C 90.INSTALL TRANSAXLE HOUSING

a.

Clean and degrease the contact surfaces of the transaxle housing and the transaxle case.


b.
C286437C01
0.979,1.74 1.146,1.521 true 0.802,1.667 1.115,1.865 0.313,0.198 10 false *a
*a Seal Packing
(Seal Diameter: 1.2 mm (0.0472 in.))


Apply a continuous bead of seal packing (Diameter 1.2 mm (0.0472 in.)) to the transaxle housing.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.



c.
C286342E01
2.156,1.74 2.313,1.938 0.156,0.198 10 false A 1.865,1.75 2.021,1.948 0.156,0.198 10 false A 2.844,0.896 3,1.094 0.156,0.198 10 true A 2.729,1.438 2.885,1.635 0.156,0.198 10 true A

Clean and degrease the 4 bolts A and bolt holes.


d.

Apply adhesive to 2 or 3 threads on the ends of the 4 bolts A.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



e.

Install the transaxle housing to the transaxle case with the 16 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 35427P 91.INSTALL B-1 ACCUMULATOR PISTON COMPRESSION SPRING

a.
C286349

Using a screwdriver, install the B-1 accumulator piston compression spring to the B-1 accumulator piston.

B-1 Accumulator Piston Compression Spring:
Free Length Outer Diameter Color
19.37 mm (0.763 in.) 15.0 mm (0.591 in.) Natural



Hide 35427R 92.INSTALL B-1 ACCUMULATOR PISTON

a.
C286440

Coat 2 new B-1 accumulator piston O-rings with Toyota Genuine ATF Type T-IV, and install them to the B-1 accumulator piston.

NOTICE:

Do not twist the O-rings.



b.
C286919

Install the B-1 accumulator piston to the transaxle case.

NOTICE:

Do not damage the O-rings.



c.

Install the No. 2 B-1 accumulator piston compression spring to the B-1 accumulator piston.

No. 2 B-1 Accumulator Piston Compression Spring:
Free Length Outer Diameter Color
47.13 mm (1.86 in.) 16.0 mm (0.630 in.) Pink



Hide 35206 93.INSTALL C-1 ACCUMULATOR SPRING SUB-ASSEMBLY

a.
C286348

Using a screwdriver, install the C-1 accumulator spring sub-assembly to the C-1 accumulator piston.

C-1 Accumulator Spring Sub-assembly:
Free Length Outer Diameter Color
24.90 mm (0.980 in.) 16.8 mm (0.661 in.) Light Blue



Hide 35424C 94.INSTALL C-1 ACCUMULATOR PISTON

a.
C286442

Coat 2 new C-1 accumulator piston O-rings with Toyota Genuine ATF Type T-IV, and install them to the C-1 accumulator piston.

NOTICE:

Do not twist the O-rings.



b.
C286920

Install the C-1 accumulator piston compression spring and the C-1 accumulator piston to the transaxle case.

C-1 Accumulator Piston Compression Spring:
Free Length Outer Diameter Color
57.90 mm (2.28 in.) 17.2 mm (0.677 in.) Natural


NOTICE:

Do not damage the O-rings.



Hide 35209 95.INSTALL C-2 ACCUMULATOR SPRING SUB-ASSEMBLY

a.
C286347

Using a screwdriver, install the C-2 accumulator spring sub-assembly to the C-2 accumulator piston with the accumulator spring hole snap ring.

C-2 Accumulator Spring Sub-assembly:
Free Length*1 Coil Outer Diameter Color
17.30 mm (0.681 in.) 13.8 mm (0.543 in.) Light Green


HINT:

*1: Including the spring retainer.



Hide 35425A 96.INSTALL C-2 ACCUMULATOR PISTON

a.
C286443

Coat 2 new C-2 accumulator piston O-rings with Toyota Genuine ATF Type T-IV, and install them to the C-2 accumulator piston.

NOTICE:

Do not twist the O-rings.



b.
C286921

Install the C-2 accumulator piston compression spring and the C-2 accumulator piston to the transaxle case.

C-2 Accumulator Piston Compression Spring:
Free Length Outer Diameter Color
57.20 mm (2.25 in.) 17.5 mm (0.689 in.) Light Green


NOTICE:

Do not damage the O-rings.



Hide 35251 97.INSTALL CHECK BALL BODY

a.
C286346

Install the check ball body compression spring and the check ball body to the transaxle case.


Hide 35159 98.INSTALL BRAKE DRUM GASKET

a.
C286375

Coat a new brake drum gasket with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 35148 99.INSTALL NO. 1 GOVERNOR APPLY GASKET

a.
C286345

Coat a new No. 1 governor apply gasket with Toyota Genuine ATF Type T-IV, and install it to the transaxle case.


Hide 82125J 100.INSTALL TRANSMISSION WIRE

a.
C282693

Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it to the transmission wire.

NOTICE:

Do not twist the O-ring.



b.
C203903

Insert the transmission wire into the transaxle case.


c.
C203904

Install the transmission wire to the transaxle case with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Do not damage the O-ring.



Hide 35410 101.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C286343

Connect the manual valve connecting rod to the manual valve lever sub-assembly.


b.
C203894N01
2.208,1.708 2.365,1.906 0.156,0.198 10 true A 2.792,1.063 2.948,1.26 0.156,0.198 10 true A 2.667,0.521 2.823,0.719 0.156,0.198 10 false A 1.99,0.073 2.146,0.271 0.156,0.198 10 false A 1.729,0.073 1.885,0.271 0.156,0.198 10 false A 1.427,0.083 1.583,0.281 0.156,0.198 10 false A 0.438,1.021 0.594,1.219 0.156,0.198 10 false B 0.448,1.396 0.604,1.594 0.156,0.198 10 false B 0.813,1.979 0.969,2.177 0.156,0.198 10 false B 1.25,1.927 1.406,2.125 0.156,0.198 10 false B 1.448,0.948 1.604,1.146 0.156,0.198 10 true B 1.833,1.75 1.99,1.948 0.156,0.198 10 false C 0.74,0.448 0.896,0.646 0.156,0.198 10 true D 1.563,1.792 1.719,1.99 0.156,0.198 10 true E

Temporarily install the transmission valve body assembly to the transaxle case with the 14 bolts.

HINT:

Bolt length:

·

Bolt A: 20 mm (0.787 in.)

·

Bolt B: 28 mm (1.10 in.)

·

Bolt C: 36 mm (1.42 in.)

·

Bolt D: 40 mm (1.57 in.)

·

Bolt E: 49 mm (1.93 in.)




c.

Tighten the 14 bolts.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)


d.
C286550C01
2.115,1.302 2.885,1.75 true 2.927,1.656 3.24,1.813 0.313,0.156 10 false *1
*1 Temperature Sensor Clamp


Engage the 2 clamps, connect the 5 connectors and install the transmission wire to the transmission valve body assembly.


e.

Engage the temperature sensor clamp and install the transmission wire to the transmission valve body assembly.


Hide 35330 102.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.

Coat the gasket of the valve body oil strainer assembly with Toyota Genuine ATF Type T-IV.


b.
C203892

Install the valve body oil strainer assembly to the transmission valve body assembly with the 3 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 35394 103.INSTALL TRANSMISSION OIL CLEANER MAGNET

a.
C286291

Install the 2 transmission oil cleaner magnets to the automatic transaxle oil pan sub-assembly.


Hide 35106D 104.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C203891

Install a new automatic transaxle oil pan gasket and the automatic transaxle oil pan sub-assembly to the transaxle case with the 18 bolts.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

NOTICE:

Completely remove any oil or grease from the contact surface of the transaxle case and the automatic transaxle oil pan sub-assembly with the automatic transaxle oil pan gasket before installation.



b.

Install a new gasket and the drain plug sub-assembly to the automatic transaxle oil pan sub-assembly.

Torque:
17.2 N*m (175 kgf*cm, 13 ft.*lbf)


Hide 32921C 105.INSTALL OIL COOLER TUBE UNION

a.
C286340

Coat 2 new O-rings with Toyota Genuine ATF Type T-IV, and install them to the 2 oil cooler tube unions.

NOTICE:

Do not twist the O-rings.



b.

Install the 2 oil cooler tube unions to the transaxle case.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)

NOTICE:

Do not damage the O-rings.



Hide 35104B 106.INSTALL NO. 1 BREATHER PLUG

a.
C286917

Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it to the No. 1 breather plug.

NOTICE:

Do not twist the O-ring.



b.

Install the No. 1 breather plug to the transaxle case.

NOTICE:

Do not damage the O-ring.



Hide 35104V 107.INSTALL BREATHER PLUG HOSE

a.
C286339

Install the breather plug hose to the No. 1 breather plug.


Hide 89413B 108.INSTALL TRANSMISSION REVOLUTION SENSOR

a.
C286338

Coat a new O-ring with Toyota Genuine ATF Type T-IV, and install it to the transmission revolution sensor.

NOTICE:

Do not twist the O-ring.



b.

Install the transmission revolution sensor to the transaxle case with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

Do not damage the O-ring.



Hide 84540 109.INSTALL PARK/NEUTRAL POSITION SWITCH

a.
C286305

Temporarily install the park/neutral position switch to the transaxle case with the 2 bolts.


b.
C286308

Install a new lock plate and the lock nut to the park/neutral position switch.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


c.
C107759C01
1.333,1.969 1.5,2.146 0.167,0.177 10 true *a 0.781,1.094 0.958,1.271 0.177,0.177 10 true *b
*a P Position
*b N Position


Temporarily install the transmission control shaft lever to the manual valve lever shaft.


d.

Rotate the transmission control shaft lever counterclockwise until it stops, and then from that position rotate it clockwise by 2 notches to set it to the N position.


e.

Remove the transmission control shaft lever from the manual valve lever shaft.


f.
C286307C01
0.833,0.76 1.531,0.927 true 0.865,1.333 1.594,1.156 true 0.677,0.646 0.99,0.802 0.313,0.156 10 false *a 0.698,1.24 1.01,1.396 0.313,0.156 10 false *b
*a Neutral Basic Line
*b Protrusion


Rotate the park/neutral position switch clockwise or counterclockwise to align the neutral basic line with the protrusion as shown in the illustration.


g.

Hold the park/neutral position switch in this position and tighten the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


h.
C286304

Using a screwdriver, secure the lock nut with the lock plate.


Hide 35572A 110.INSTALL TRANSMISSION CONTROL SHAFT LEVER

a.
C286302

Install the transmission control shaft lever to the automatic transaxle assembly with the washer and nut.

Torque:
12.3 N*m (125 kgf*cm, 9 ft.*lbf)