Home › Drivetrain › U441E AUTOMATIC TRANSMISSION / TRANSAXLE › OIL PUMP › 2013.08–2016.10
RM30M0E _52 Drivetrain _017088 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0090630 OIL PUMP G

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  OIL PUMP  INSPECTION  


PROCEDURE

Hide 35370 1.INSPECT STATOR SHAFT ASSEMBLY

a.
C286450

Using a caliper gauge, measure the inside diameter of the stator shaft bush.

Standard inside diameter:

18.424 to 18.450 mm (0.7254 to 0.7263 in.)


Maximum inside diameter:

18.450 mm (0.7263 in.)


If the inside diameter is greater than the maximum, replace the stator shaft assembly.


b.
C286451

Install the input shaft sub-assembly onto the stator shaft assembly, and check that the input shaft sub-assembly turns smoothly.

NOTICE:

Replace the stator shaft assembly with a new one if it moves roughly or makes unusual noise.

Inspect the input shaft's contact surface with the bearing when replacing, and replace the input shaft sub-assembly with a new one if any damage or discoloration is found.



Hide 2.INSPECT FRONT OIL PUMP BODY

a.
C286452

Using a caliper gauge, measure the inside diameter of the front oil pump body bush.

Standard inside diameter:

38.113 to 38.138 mm (1.5006 to 1.5014 in.)


Maximum inside diameter:

38.138 mm (1.5014 in.)


If the inside diameter is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear and the front oil pump body.


Hide 3.INSPECT FRONT OIL PUMP GEAR CLEARANCE

a.
C286453

Using a feeler gauge, measure the clearance between the tips of the front oil pump driven gear teeth and the front oil pump drive gear teeth.

Standard tip clearance:

0.07 to 0.15 mm (0.00276 to 0.00590 in.)


Maximum tip clearance:

0.15 mm (0.00590 in.)


If the tip clearance is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear and the front oil pump body.


b.
C286454

Using a feeler gauge, measure the clearance between the front oil pump driven gear and the front oil pump body.

Standard body clearance:

0.10 to 0.17 mm (0.00394 to 0.00669 in.)


Maximum body clearance:

0.17 mm (0.00669 in.)


If the body clearance is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear and the front oil pump body.


c.
C286455

Using a straightedge and feeler gauge, measure the side clearance of the front oil pump drive gear and the front oil pump driven gear.

Standard side clearance:

0.02 to 0.05 mm (0.000788 to 0.00196 in.)


Maximum side clearance:

0.05 mm (0.00196 in.)


If the side clearance is greater than the maximum, replace the front oil pump drive gear, front oil pump driven gear and the front oil pump body.

Front Oil Pump Drive Gear Thickness:
Part No. Mark Thickness
mm (in.)
35321-52010 1 8.445 (0.3325)
35321-52020 2 8.455 (0.3329)
35321-52030 3 8.465 (0.3333)
35321-52040 4 8.475 (0.3337)
35321-52050 5 8.485 (0.3341)


Front Oil Pump Driven Gear Thickness:
Part No. Mark Thickness
mm (in.)
35322-52010 1 8.445 (0.3325)
35322-52020 2 8.455 (0.3329)
35322-52030 3 8.465 (0.3333)
35322-52040 4 8.475 (0.3337)
35322-52050 5 8.485 (0.3341)