When a trigger switch is pressed, the certification ECU (smart key control ECU assembly) generates a request signal and sends it to the No. 1 indoor electrical key antenna assembly (center pillar RH)*1 or No. 1 indoor electrical key antenna assembly (center pillar LH)*2. The No. 1 indoor electrical key antenna assembly (center pillar RH)*1 or No. 1 indoor electrical key antenna assembly (center pillar LH)*2 transmits the received signal within an area of approximately 0.7 m (2.30 ft.) from the driver side door in order to detect the person carrying the electrical key transmitter sub-assembly. DTC B27A2 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (center pillar RH)*1 or No. 1 indoor electrical key antenna assembly (center pillar LH)*2 (between terminals CLG2 and ANTE2, or terminals CG2B and CLGB).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B27A2 | Open in Front Passenger Side Electrical Antenna Circuit | An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (center pillar RH)*1 or No. 1 indoor electrical key antenna assembly (center pillar LH)*2 (CLG2 - ANTE2, CG2B - CLGB) (This is detected by the malfunction detection circuit in the certification ECU (smart key ECU assembly)) (1 trip detection logic*3). | ·
Wire harness or connector ·
No. 1 indoor electrical key antenna assembly (center pillar RH)*1 ·
No. 1 indoor electrical key antenna assembly (center pillar LH)*2 ·
Certification ECU (smart key ECU assembly) |
DTC Output Confirmation Operation
Any time |
*1: for LHD
*2: for RHD
*3: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
·
Power source mode does not change when engine switch pressed ·
Electrical key transmitter sub-assembly locked inside vehicle |
- |
| DTC Code | Data List and Active Test |
|---|---|
| B27A2 | Key diagnostic mode can be used to perform troubleshooting |
The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.
After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".
The No. 1 indoor electrical key antenna assembly (center pillar RH)*1 or No. 1 indoor electrical key antenna assembly (center pillar LH)*2 has an antenna coil between ANTE2 and CLGB terminals.
*1: for LHD
*2: for RHD
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Turn the engine switch off.
Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (center pillar RH).
Connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F44 certification ECU (smart key ECU assembly) connector.
Disconnect F48 No. 1 indoor electrical key antenna assembly (center pillar RH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-6 (CLG2) - F48-1 (ANTE2) | Always | Below 1 Ω |
| F44-23 (CG2B) - F48-3 (CLGB) | Always | Below 1 Ω |
| F44-6 (CLG2) or F48-1 (ANTE2) - Body ground | Always | 10 kΩ or higher |
| F44-23 (CG2B) or F48-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F44 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-10 (E) - Body ground | Always | Below 1 Ω |
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
*b | Waveform 1 |
| *c | Within approximately 30 seconds from when the door is closed | *d | After approximately 30 seconds from when the door is closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F44-6 (CLG2) - F43-10 (E) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| F44-23 (CG2B) - F43-10 (E) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the No. 1 indoor electrical key antenna assembly (center pillar RH) with a new or known good one.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check the DTCs.
DTC B27A2 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the engine switch off.
Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (center pillar LH).
Connectors are properly connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F44 certification ECU (smart key ECU assembly) connector.
Disconnect F49 No. 1 indoor electrical key antenna assembly (center pillar LH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F44-6 (CLG2) - F49-1 (ANTE2) | Always | Below 1 Ω |
| F44-23 (CG2B) - F49-3 (CLGB) | Always | Below 1 Ω |
| F44-6 (CLG2) or F49-1 (ANTE2) - Body ground | Always | 10 kΩ or higher |
| F44-23 (CG2B) or F49-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the F44 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F43-10 (E) - Body ground | Always | Below 1 Ω |
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
*b | Waveform 1 |
| *c | Within approximately 30 seconds from when the door is closed | *d | After approximately 30 seconds from when the door is closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| F44-6 (CLG2) - F43-10 (E) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| F44-23 (CG2B) - F43-10 (E) | Procedure:
1.
Engine switch off 2.
Electrical key transmitter sub-assembly not inside vehicle 3.
Door is open 4.
Door is closed 5.
Within 30 seconds |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the No. 1 indoor electrical key antenna assembly (center pillar LH) with a new or known good one.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check the DTCs.
DTC B27A2 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG