CHECK SMART ENTRY AND START SYSTEM (for Entry Function) OPERATION
Make sure that the smart entry and start system (for Entry Function) has not been canceled before performing this inspection.
Check the entry unlock function (driver door).
| *1 | Trigger Switch |
Perform a wireless lock operation to lock the door, pressed the trigger switch on the front door outside handle assembly (for driver door) of the driver door while carrying the electrical key transmitter sub-assembly and check that the door unlocks.
To perform a wireless lock operation, press the lock button of the electrical key transmitter sub-assembly while standing near the front door outside handle assembly (for driver door).
| *A | for LHD |
| *B | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Inspect the entry unlock detection area. Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly (for driver door) and hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly (for driver door) at a distance of approximately 0.7 m (2.30 ft.), press the trigger switch, and check that all doors unlock.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the front door outside handle assembly (for driver door).
| *1 | Trigger Switch |
Check the entry lock function (driver door).
If the electrical key transmitter sub-assembly is inside the vehicle but outside the detection area (for example, on top of the instrument panel, on the floor, near the center pillar LH or RH, in the door pockets, in the glove box, or in a storage compartment) and a door lock operation is performed, the key lock-in prevention function will not operate and the electrical key transmitter sub-assembly will be locked inside the vehicle.
With the door closed and unlocked, pressed the trigger switch on the front door outside handle assembly (for driver door) of the driver door while carrying the electrical key transmitter sub-assembly and check that the door locks.
| *A | for LHD |
| *B | for RHD |
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
Inspect the entry lock operating range. Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly (for driver door) at a distance of approximately 0.7 m (2.30 ft.), press the trigger switch, and check that all doors lock.
If the key lock-in prevention function buzzer sounds, electric waves from the indoor electrical key antenna may be leaking from the vehicle.
Check the entry luggage compartment door open function.
| *a | Approximately 0.7 m (2.30 ft.) |
Perform a wireless lock operation to lock the doors, operate the unlock switch of the luggage door opening switch assembly while carrying the electrical key transmitter sub-assembly and check that the luggage compartment door open.
Inspect the entry luggage compartment door unlock operating range. While standing at the rear of the vehicle, hold the electrical key transmitter sub-assembly so that it is facing the direction shown in the above illustration at the same height as the luggage door opening switch assembly and approximately 0.7 m (2.30 ft.) from the vehicle, press the unlock switch of the luggage door opening switch assembly and check that the luggage compartment door open.
Check the key lock-in prevention function (vehicle interior).
In order to prevent the electrical key transmitter sub-assembly from being locked inside the vehicle, perform this inspection with the window of a door open.
Turn the engine switch off.
Place the electrical key transmitter sub-assembly on a front or rear seat.
Close the door, making sure the doors are unlocked.
Press the trigger switch on the front door outside handle assembly (for driver door) and check that the doors do not lock and the key lock-in prevention function buzzer (external) sounds for approximately 5 seconds.
Check the push start function. (for Automatic Transaxle)
With the engine switch off, move the shift lever to P, depress the brake pedal while carrying the electrical key transmitter sub-assembly and check that the smart warning light in the combination meter assembly illuminates green. Then, when the smart warning light in the combination meter assembly illuminates green, press the engine switch and check that the engine starts.
With the brake pedal released and the engine switch off, press the engine switch while carrying the electrical key transmitter sub-assembly and check that the power source mode changes as follows: off → on (ACC) → on (IG) → off. However, if the shift lever is in any position other than P while the engine switch is on (IG), the power source mode will not change to off, but to on (ACC).
Stop the vehicle, press the engine switch and check that the power source mode changes to off (the engine stops and all electrical systems are off). However, if the shift lever is in any position other than P, even if the engine switch is pressed while the vehicle is stationary, the power source mode will not change to off, but to on (ACC). Move the shift lever to P, open the door and check that the steering lock operates.
| *a | Inspection Point |
Inspect the push start operating range (front floor). Place the electrical key transmitter sub-assembly on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.
Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in a door pocket, in the glove box, on the floor or in a storage compartment.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the shift lever.
Perform the inspection for both inspection points.
| *a | Inspection Point |
Inspect the push start operating range (rear floor). Place the key on the rear seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.
Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in a door pocket, in the glove box, on the floor or in a storage compartment.
Communication may not be possible if the key is within 0.2 m (0.66 ft.) of the center of the rear seat cushion.
Perform the inspection for both inspection points.
Check the push start function. (for Manual Transaxle)
With the engine switch off, depress the clutch pedal while carrying the electrical key transmitter sub-assembly and check that the smart warning light in the combination meter assembly illuminates green. Then, when the smart warning light in the combination meter assembly illuminates green, press the engine switch and check that the engine starts.
With the clutch pedal released and the engine switch off, press the engine switch while carrying the electrical key transmitter sub-assembly and check that the power source mode changes as follows: off → on (ACC) → on (IG) → off.
Stop the vehicle, press the engine switch and check that the power source mode changes to off (the engine stops and all electrical systems are off).
| *a | Inspection Point |
Inspect the push-button start operating range (front floor). Place the electrical key transmitter sub-assembly on the front seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.
Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in a door pocket, in the glove box, on the floor or in a storage compartment.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the shift lever.
Perform the inspection for both inspection points.
| *a | Inspection Point |
Inspect the push-button start operating range (rear floor). Place the key on the rear seat at either inspection point so that it is facing in the direction shown in the illustration and check that the engine can be started.
Even if the electrical key transmitter sub-assembly is within the vehicle interior detection area, the electrical key transmitter sub-assembly may not be properly detected if it is on the instrument panel, in a door pocket, in the glove box, on the floor or in a storage compartment.
Communication may not be possible if the key is within 0.2 m (0.66 ft.) of the center of the rear seat cushion.
Perform the inspection for both inspection points.
Check the transmitter battery saving function
Press the unlock switch of the electrical key transmitter sub-assembly twice while pressing the lock switch and check that the electrical key transmitter sub-assembly LED blinks 4 times and enters transmitter battery saving mode.
Check that the smart entry and start system (for Entry Function) does not operate while in transmitter battery saving mode.
To cancel transmitter battery saving mode, press a switch of the electrical key transmitter sub-assembly.
Check the entry cancel function.
Cancel the smart entry and start system and check that all the functions of the smart entry and start system (for Entry Function) no longer operate.
Refer to the following procedures to cancel the smart entry and start system (for Entry Function).
While the smart entry and start system is canceled, it is possible to lock and unlock the doors with the wireless operation, and the start system can be operated by holding the electrical key transmitter sub-assembly near the engine switch.
While the key cancel function (entry cancel function) is on, check that all functions of the smart entry and start system cannot be operated.
Check the answer-back function (hazard warning light flashing and buzzer sounding).
| Entry Operation | Wireless Buzzer | Hazard Warning Light |
|---|---|---|
| Entry Door Lock | Sounds once | Flashes once |
| Entry Door Unlock | Sounds twice | Flashes twice |
| Entry Luggage Compartment Door Open | Sounds once | Does not flash |
KEY DIAGNOSTIC MODE (Using GTS)
With key diagnostic mode, it is possible to check if the electrical key transmitter sub-assembly is operating properly with the selected electrical key antenna and within the selected detection area by the sounding of the wireless buzzer.
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
Enter the following menus: Body Electrical / Entry&Start / Utility / Communication Check (Key Diag Mode).
Inspect the appropriate item according to the following table.
| Tester Display | Inspection Item |
|---|---|
| [CH1/CH2] Overhead + Driver Side*1 | No. 1 indoor electrical key antenna assembly (center pillar LH)*7
No. 1 indoor electrical key antenna assembly (center pillar RH)*8 |
| [CH1] Overhead + Driver Side*1 | |
| [CH2] Overhead + Driver Side*1 | |
| [CH1/CH2] Overhead + Passenger Side*2 | No. 1 indoor electrical key antenna assembly (center pillar RH)*7
No. 1 indoor electrical key antenna assembly (center pillar LH)*8 |
| [CH1] Overhead + Passenger Side*2 | |
| [CH2] Overhead + Passenger Side*2 | |
| [CH1/CH2] Overhead + Front Room*3 | No. 1 indoor electrical key antenna assembly (center pillar RH)
No. 1 indoor electrical key antenna assembly (center pillar LH) |
| [CH1] Overhead + Front Room*3 | |
| [CH2] Overhead + Front Room*3 | |
| [CH1/CH2] Overhead + Luggage*4 | No. 3 indoor electrical key antenna assembly (luggage compartment) |
| [CH1] Overhead + Luggage*4 | |
| [CH2] Overhead + Luggage*4 | |
| [CH1/CH2] Immobiliser Amp*5 | Amplifier (engine switch) |
| [CH1] Immobiliser Amp*5 | |
| [CH2] Immobiliser Amp*5 | |
| [CH1/CH2] Overhead + Room*6 | No. 2 indoor electrical key antenna assembly (rear floor) |
| [CH1] Overhead + Room*6 | |
| [CH2] Overhead + Room*6 |
*7: for LHD
*8: for RHD
Bring the electrical key transmitter sub-assembly near the selected electrical key antenna and check that the wireless door lock buzzer sounds.
| *a | 0.7 to 1 m (2.30 to 3.28 ft.) |
*1: No. 1 indoor electrical key antenna assembly (center pillar RH)
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Hold the electrical key transmitter sub-assembly at the same height as the front door outside handle assembly (for driver door) in the position shown in the illustration.
*2: Perform the same inspection for the front passenger side.
| *a | Inspection Point |
*3: No. 1 indoor electrical key antenna assembly (center pillar RH) and No. 1 indoor electrical key antenna assembly (center pillar LH)
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Place the electrical key transmitter sub-assembly on the front seat cushion of the driver seat or front passenger seat.
| *a | Inspection Point |
*6: No. 2 indoor electrical key antenna assembly (rear floor)
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Place the electrical key transmitter sub-assembly on the rear seat cushion.
| *a | Approximately 0.7 m (2.30 ft.) |
*4: No. 3 indoor electrical key antenna assembly (luggage compartment)
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
Hold the electrical key transmitter sub-assembly at the same height as the rear bumper upper surface and align it with the center of the rear of the vehicle, as shown in the illustration.
*5: Amplifier (engine switch)
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
While facing the logo side of the electrical key transmitter sub-assembly towards the engine switch, hold the transmitter near the engine switch.