Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Entry Function) › 2013.08–2014.03
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090849 SMART ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Entry Function)  B27A8  Open in Outside Luggage Compartment Electrical Key Antenna Circuit  


DESCRIPTION

When the luggage door opening switch assembly is pressed certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 3 indoor electrical key antenna assembly (luggage compartment). The electrical key antenna transmits the received signal within an area of approximately 0.7 m (2.30 ft.) from the luggage compartment door in order to detect the person carrying the electrical key transmitter sub-assembly. DTC B27A8 is stored by the certification ECU (smart key ECU assembly) when an open circuit is detected between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (luggage compartment) (between terminals CLG8 and ANTE8, or terminals CG8B and CLGB).

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B27A8 Open in Outside Luggage Compartment Electrical Key Antenna Circuit An open circuit is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (luggage compartment) (CLG8 - ANTE8, CG8B - CLGB) (1 trip detection logic*).
·

Wire harness or connector

·

No. 3 indoor electrical key antenna assembly (luggage compartment)

·

Certification ECU (smart key ECU assembly)


DTC Output Confirmation Operation

Any time



*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Entry unlock operation cannot be performed for luggage compartment door -

Related Data List and Active Test
DTC Code Data List and Active Test
B27A8 Key diagnostic mode can be used to perform troubleshooting

WIRING DIAGRAM

B286267
1.229,0.979 2,1.177 0.771,0.198 10 false ANTE8 1.75,0.854 2.521,1.052 0.771,0.198 10 false 1 1.75,1.302 2.521,1.5 0.771,0.198 10 false 3 5.531,1 6.302,1.198 0.771,0.198 10 false CLG8 5.531,1.438 6.302,1.635 0.771,0.198 10 false CG8B 5.542,1.885 6.313,2.083 0.771,0.198 10 false E 5.219,1.875 5.99,2.073 0.771,0.198 10 false F43 5.24,1.698 6.01,1.896 0.771,0.198 10 false 10 5.219,1.448 5.99,1.646 0.771,0.198 10 false F44 5.25,1.25 6.021,1.448 0.771,0.198 10 false 24 5.208,1.01 5.979,1.208 0.771,0.198 10 false F44 5.281,0.813 6.052,1.01 0.771,0.198 10 false 8 1.302,1.438 2.073,1.635 0.771,0.198 10 false CLGB 0.438,2.417 1.208,2.615 0.771,0.198 10 false L4 0.438,2.594 2.083,3.385 1.646,0.792 10 false No. 3 Indoor Electrical Key Antenna Assembly (Luggage Compartment) 5.188,2.417 6.771,2.979 1.583,0.563 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

The smart entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the GTS with the vehicle engine switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

Before replacing the certification ECU (smart key ECU assembly), refer to the smart entry and start system (for Entry Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>PRECAUTION

·

After repair, confirm that no DTCs are output by performing the "DTC Output Confirmation Operation".

·

The No. 3 indoor electrical key antenna assembly (luggage compartment) has an antenna coil between ANTE8 and CLGB terminals.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 3 indoor electrical key antenna assembly (luggage compartment).

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT))

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT))
a.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L4 No. 3 indoor electrical key antenna assembly (luggage compartment) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-8 (CLG8) - L4-1 (ANTE8) Always Below 1 Ω
F44-24 (CG8B) - L4-3 (CLGB) Always Below 1 Ω
F44-8 (CLG8) or L4-1 (ANTE8) - Body ground Always 10 kΩ or higher
F44-24 (CG8B) or L4-3 (CLGB) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT))
a.

Connect the F44 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F43-10 (E) - Body ground Always Below 1 Ω



c.

Using an oscilloscope, check the waveform.

B333751C05
2.5,0.313 2.917,0.563 0.417,0.25 4.417,0.313 4.833,0.563 0.417,0.25 1.917,2.25 2.177,1.333 true 4.281,2.271 4.948,1.333 true 5.385,2.271 4.969,1.396 true 3.167,4.5 3.313,3.74 true 0.406,0.271 0.719,0.427 0.313,0.156 10 false *a 2.594,2.875 2.906,3.031 0.313,0.156 10 false *b 3.073,4.49 3.385,4.646 0.313,0.156 10 false *c 2.594,0.354 3.052,0.552 0.458,0.198 10 false F43 4.521,0.344 4.979,0.542 0.458,0.198 10 false F44 1.865,2.313 2.323,2.51 0.458,0.198 10 false E 2.365,3.604 2.823,3.802 0.458,0.198 10 false GND 4.063,2.323 4.521,2.521 0.458,0.198 10 false CLG8 5.208,2.323 5.667,2.521 0.458,0.198 10 false CG8B
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
*b Waveform 1
*c Luggage door opening switch assembly is pressed - -


OK:
Tester Connection Condition Tool Setting Specified Condition
F44-8 (CLG8) - F43-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Luggage door opening switch assembly off → on


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)
F44-24 (CG8B) - F43-10 (E) Procedure:
1.

Engine switch off

2.

All doors closed

3.

Luggage door opening switch assembly off → on


2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform 1)



Result:
Proceed to
OK
NG



OK

4.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4.REPLACE NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT)
a.

Temporarily replace the No. 3 indoor electrical key antenna assembly (luggage compartment) with a new or known good one.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Luggage Compartment)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CLEAR DTC
5.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Clear DTCs
50002 125

Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Entry Function)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
OK:

DTC B27A8 is not output.



Result:
Proceed to
OK
NG



OK

END (NO. 3 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (LUGGAGE COMPARTMENT) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)