Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › 2013.08–2016.04
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090851 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  Immobiliser System does not Operate Properly  


DESCRIPTION

The immobiliser system compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.

The system unsets if these ID codes match. Thus, the certification ECU (smart key ECU assembly) and the ECM communicate with each other enabling the engine to start.

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the vehicle engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The immobiliser system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the immobiliser system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation."

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR



HINT:

When the ECM and certification ECU (smart key ECU assembly) DTC are output simultaneously, first perform troubleshooting for the ECM and certification ECU (smart key ECU assembly) DTC.


PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/ Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Entry&Start > Trouble Codes
50001 125
Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC is not output A
DTC is output B



A

2.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

2.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Normal Condition Reference Value Diagnostic Note
Immobiliser Fuel Cut Immobiliser fuel cut status ON or OFF ON: Immobiliser fuel cut on
OFF: Immobiliser fuel cut off
-
Powertrain > Engine and ECT > Data List
Tester Display
Immobiliser Fuel Cut
50003 234 505

Result:
Result Proceed to
"ON" is displayed on the Data List screen of the GTS (for 1NZ-FE with Automatic Transaxle) A
"ON" is displayed on the Data List screen of the GTS (for 1NZ-FE with Manual Transaxle) B
"ON" is displayed on the Data List screen of the GTS (for 2NZ-FE with Automatic Transaxle) C
"ON" is displayed on the Data List screen of the GTS (for 2NZ-FE with Manual Transaxle) D
"OFF" is displayed on the Data List screen of the GTS E



A

B

C

D

E

3.CHECK WHETHER ENGINE STARTS
3.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts 5 seconds after the engine switch turned on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

4.INSPECT ECM (TERMINAL IMI AND IMO)
4.INSPECT ECM (TERMINAL IMI AND IMO)
a.

for Automatic Transaxle:

i.

Using an oscilloscope, check the waveform.

E273501C03
4.333,0.156 4.75,0.417 0.417,0.26 2.99,3.344 2.969,3.76 true 3.396,5.396 3.333,5.792 true 3.896,1.083 3.708,1.74 true 4.01,1.094 4.125,1.729 true 1.292,1.99 1.604,2.146 0.313,0.156 10 false *1 1.271,4.115 1.583,4.271 0.313,0.156 10 false *2 2.208,6.198 2.521,6.354 0.313,0.156 10 false *3 3.031,2.365 3.344,2.521 0.313,0.156 10 false *4 3.427,4.313 3.74,4.469 0.313,0.156 10 false *5 0.656,0.281 0.969,0.438 0.313,0.156 10 false *a 2.865,3.781 3.177,3.938 0.313,0.156 10 false *b 3.115,3.406 3.427,3.563 0.313,0.156 10 false *c 3.531,5.479 3.844,5.635 0.313,0.156 10 false *c 2.375,4.302 2.688,4.458 0.313,0.156 10 false *3 3.24,5.802 3.552,5.958 0.313,0.156 10 false *b 2.646,6.979 2.958,7.177 0.313,0.198 10 false *d 4.677,6.969 4.99,7.167 0.313,0.198 10 false *d 2.729,7.219 3.042,7.417 0.313,0.198 10 false *e 4.615,7.229 4.927,7.427 0.313,0.198 10 false *e 3.813,6.76 4.125,6.958 0.313,0.198 10 false or 1,5.354 1.458,5.552 0.458,0.198 10 false GND 0.99,3.313 1.448,3.51 0.458,0.198 10 false GND 4.438,0.208 4.896,0.406 0.458,0.198 10 false F82 3.604,1.771 3.844,2.063 0.24,0.292 10 false IMI 4.021,1.76 4.375,2.094 0.354,0.333 10 false IMO
*1 Waveform (IMO) *2 Waveform (IMI)
*3 Waveform A *4 Waveform B
*5 Waveform C - -
*a Component with harness connected
(ECM)
*b Approximately 160 ms
*c Approximately 270 ms *d Approximately 40 ms
*e Approximately 60 ms - -


HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Measurement Condition:
Item Content
Tester Connection F82-15 (IMO) - Body ground
F82-16 (IMI) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected




b.

for Manual Transaxle:

i.

Using an oscilloscope, check the waveform.

E272488C02
2.198,0.177 2.615,0.469 0.417,0.292 1.917,1.698 2.125,1.125 true 2.448,1.698 2.25,1.125 true 2.938,3.813 2.99,3.354 true 3.333,5.844 3.385,5.385 true 1.167,0.302 1.479,0.5 0.313,0.198 10 false *a 2.292,0.24 2.656,0.448 0.365,0.208 10 false F81 1.813,1.74 2.177,1.948 0.365,0.208 10 false IMI 2.375,1.74 2.74,1.948 0.365,0.208 10 false IMO 1.167,2.021 1.479,2.219 0.313,0.198 10 false *1 3.031,2.385 3.344,2.583 0.313,0.198 10 false *4 3.115,3.406 3.427,3.604 0.313,0.198 10 false *c 2.865,3.854 3.177,4.052 0.313,0.198 10 false *b 0.938,3.313 1.302,3.521 0.365,0.208 10 false GND 1.135,4.094 1.448,4.292 0.313,0.198 10 false *2 0.927,5.344 1.292,5.552 0.365,0.208 10 false GND 2.438,4.333 2.75,4.531 0.313,0.198 10 false *3 3.427,4.333 3.74,4.531 0.313,0.198 10 false *5 3.51,5.427 3.823,5.625 0.313,0.198 10 false *c 3.25,5.875 3.563,6.073 0.313,0.198 10 false *b 2.219,6.198 2.531,6.396 0.313,0.198 10 false *3 2.646,6.979 2.958,7.177 0.313,0.198 10 false *d 2.719,7.24 3.031,7.438 0.313,0.198 10 false *e 4.656,6.969 4.969,7.167 0.313,0.198 10 false *d 4.594,7.229 4.906,7.427 0.313,0.198 10 false *e 3.74,6.771 4.052,6.969 0.313,0.198 10 false or
*1 Waveform (IMO) *2 Waveform (IMI)
*3 Waveform A *4 Waveform B
*5 Waveform C - -
*a Component with harness connected
(ECM)
*b Approximately 160 ms
*c Approximately 270 ms *d Approximately 40 ms
*e Approximately 60 ms - -


HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


Measurement Condition:
Item Content
Tester Connection F81-18 (IMO) - Body ground
F81-19 (IMI) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds after engine starts, or within 3 seconds after engine switch turned on (IG) after battery disconnected and reconnected


Result:
Result Proceed to
Normal waveform A
Waveform A not output, or has abnormal wavelength or shape B
Waveform B not output, or has abnormal wavelength or shape (for 1NZ-FE) C
Waveform B not output, or has abnormal wavelength or shape (for 2NZ-FE) D
Waveform C not output, or has abnormal wavelength or shape E





A

5.REGISTER ECU COMMUNICATION ID

B

7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)

C

D

E

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
5.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM)
a.

Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

for Automatic Transaxle:

i.

Disconnect the F82 ECM connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-35 (EFIO) - F82-16 (IMI) Always Below 1 Ω
F44-35 (EFIO) - Body ground Always 10 kΩ or higher
F82-16 (IMI) - Body ground Always 10 kΩ or higher




c.

for Manual Transaxle:

i.

Disconnect the F81 ECM connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F44-35 (EFIO) - F81-19 (IMI) Always Below 1 Ω
F44-35 (EFIO) - Body ground Always 10 kΩ or higher
F81-19 (IMI) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.REGISTER RECOGNITION CODES
9.REGISTER RECOGNITION CODES
a.

Register the recognition codes in the ECUs.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.REGISTER ECU COMMUNICATION ID
10.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER ENGINE STARTS
11.CHECK WHETHER ENGINE STARTS
a.

Using a registered vehicle key, turn the engine switch on (IG).

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (for 1NZ-FE with Automatic Transaxle) B
NG (for 1NZ-FE with Manual Transaxle) C
NG (for 2NZ-FE with Automatic Transaxle) D
NG (for 2NZ-FE with Manual Transaxle) E



A

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

B

C

D

E