Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System)
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090852 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  B2793  Transponder Chip Malfunction  B2794  Unmatched Encryption Code  B2797  Communication Malfunction No. 1  B2798  Communication Malfunction No. 2  


DESCRIPTION

·

DTC B2793 is stored when a malfunction is found in the key during key ID code registration or a key ID code is not registered normally. Replace the key if key ID code registration cannot be performed normally and this DTC is output.

·

DTC B2794 is stored when a key with an incomplete key ID code is inserted into the ignition key cylinder.

·

DTC B2797 is stored when a key with a BCC malfunction is inserted into the ignition key cylinder.

·

DTC B2798 is stored when a key is inserted into the ignition key cylinder, and the ignition switch is turned on, but a communication error occurs between the key and transponder key ECU assembly.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2793 Transponder Chip Malfunction A transponder chip malfunction (1 trip detection logic*1).
·

Key

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder, and the ignition switch is turned on.


B2794 Unmatched Encryption Code A key with an incomplete key ID code is inserted into the ignition key cylinder (1 trip detection logic*1).
·

Key

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder, and the ignition switch is turned on.


B2797 Communication Malfunction No. 1 A key with a BCC malfunction is inserted into the ignition key cylinder (1 trip detection logic*1).
·

Key

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder, and the ignition switch is turned on.


B2798 Communication Malfunction No. 2 Key ID code identification cannot be completed within the specified time (1 trip detection logic*1).
·

Key

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Insert the key into the ignition key cylinder, and the ignition switch is turned on.



*1: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2793 Abnormal Status
B2794 Different Encrypt Code
B2797 Bcc Malfunction
B2798 Frame Error

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or key is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Insert and remove each registered key one at a time, and check for DTCs each time.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
HINT:
·

Before checking for DTCs, perform "DTC Output Confirmation Operation" procedure.

·

If DTC B2793, B2794, B2797 or B2798 are stored, clear the DTCs before checking the next key.



OK:

DTC B2793, B2974, B2797 and B2798 is not output.



Result:
Result Proceed to
DTCs are not output A
DTCs are output for all of the keys B
DTCs are output for any of the keys C



A

B

REPLACE TRANSPONDER KEY ECU ASSEMBLY

C

REPLACE KEY THAT DTC IS OUTPUT