Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › 2013.08–2017.10
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090852 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  Security Indicator Light Does not Blink  


DESCRIPTION

The transponder key ECU assembly blinks the security indicator light when the immobiliser is set.

WIRING DIAGRAM

B343160E02
1.417,1.083 1.677,1.26 0.26,0.177 10 false 21 2.698,1.073 2.958,1.25 0.26,0.177 10 false 13 2.417,1.167 2.677,1.344 0.26,0.177 10 false LP 1.667,1.177 1.927,1.354 0.26,0.177 10 false ED 1.302,1.865 1.563,2.042 0.26,0.177 10 false F38 1.281,2.021 3.167,2.229 1.885,0.208 10 false Combination Meter Assembly 4.573,1.083 4.833,1.26 0.26,0.177 10 false 3 4.833,1.167 5.146,1.344 0.313,0.177 10 false IND 4.344,1.854 4.604,2.031 0.26,0.177 10 false F51 4.333,2.021 6.448,2.229 2.115,0.208 10 false Transponder Key ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly is replaced, refer to Service Bulletin.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Immobiliser / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
OK:

Security indicator light can be turned on and off using the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the F51 transponder key ECU assembly connector.


b.

Disconnect the F38 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-13 (LP) - F51-3 (IND) Always Below 1 Ω
F38-21 (ED) - Body ground Always Below 1 Ω
F38-13 (LP) - Body ground Always 10 kΩ or higher
F51-3 (IND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK TRANSPONDER KEY ECU ASSEMBLY (TERMINAL IND)
a.

Connect the F51 transponder key ECU assembly connector.


b.
B348677
1.469,0.25 1.896,0.51 0.427,0.26 1.885,1.833 2.052,1.229 true 1.552,0.292 1.844,0.521 0.292,0.229 10 false F38 1.802,1.875 2.094,2.104 0.292,0.229 10 false LP 0.188,0.177 0.479,0.406 0.292,0.229 10 false *a
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the voltage and check for pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F38-13 (LP) - Body ground Ignition switch off Pulse generation
Ignition switch ON Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY