Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › DRIVE BELT › 2013.08–2016.07
RM30M0E _51 Engine / Hybrid System _017073 1NZ-FE ENGINE MECHANICAL _0090999 DRIVE BELT A

1NZ-FE ENGINE MECHANICAL  DRIVE BELT  INSTALLATION  


PROCEDURE

Hide 16361A 1.INSTALL FAN AND GENERATOR V BELT

a.
A111165C02
1.104,1.708 1.365,1.667 true 1.083,3.802 1.344,3.76 true 2.313,0.604 2.573,0.563 true 2.323,2.698 2.583,2.656 true 2.302,1.271 2.563,1.229 true 2.344,3.292 2.604,3.25 true 2.438,4.021 2.698,3.979 true 0.104,0.135 0.417,0.292 0.313,0.156 12 false *A 0.115,2.469 0.396,2.698 0.281,0.229 12 false *B 0.885,1.646 1.094,1.823 0.208,0.177 10 false *1 2.625,0.49 2.938,0.646 0.313,0.156 10 false *2 2.625,1.156 2.938,1.313 0.313,0.156 10 false *3 2.76,3.917 3.073,4.073 0.313,0.156 10 false *4 0.906,3.75 1.115,3.927 0.208,0.177 10 false *1 2.646,2.552 2.958,2.708 0.313,0.156 10 false *2 2.656,3.156 2.969,3.313 0.313,0.156 10 false *3
*A w/o Air Conditioning System
*B w/ Air Conditioning System
*1 Crankshaft Damper Sub-assembly
*2 Generator with Regulator Assembly
*3 Engine Water Pump Assembly
*4 Cooler Compressor Assembly


Temporarily install the fan and generator V belt to each pulley.

NOTICE:
·

Make sure that there is no foreign matter or liquid, such as oil, on the fan and generator V belt and pulleys.

·

Make sure that the fan and generator V belt is securely fitted into the rib grooves of the pulley.




Hide 16361A 2.ADJUST FAN AND GENERATOR V BELT

a.
A116198C01
0.344,1.021 0.656,1.177 0.313,0.156 10 false *a 2.427,0.313 2.74,0.469 0.313,0.156 10 false *b
*a OK
*b NG
V100135

Front of Vehicle


Insert an adjusting bar between the engine mounting insulator sub-assembly RH and generator with regulator assembly. Pull the adjusting bar toward the vehicle front to adjust the fan and generator V belt tension.

NOTICE:

Do not insert the adjusting bar between the camshaft timing oil control valve assembly and generator with regulator assembly. It could damage the camshaft timing oil control valve assembly.



b.
A111164E02
2.281,0.365 2.438,0.563 0.156,0.198 10 false A 1.969,1.948 2.125,2.146 0.156,0.198 10 false B

First tighten the bolt A, then tighten the bolt B.

Torque:
Bolt A : 18.5 N*m (189 kgf*cm, 14 ft.*lbf)
Bolt B : 54 N*m (551 kgf*cm, 40 ft.*lbf)


Hide 16361A 3.INSPECT FAN AND GENERATOR V BELT

Hide 51441C 4.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

a.

Install the engine under cover RH to the vehicle with the 2 bolts and 4 screws.

Torque:
Bolt : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 51405A 5.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 6.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)