Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › CYLINDER BLOCK › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017073 1NZ-FE ENGINE MECHANICAL _0091009 CYLINDER BLOCK A

1NZ-FE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 13516B 1.INSTALL OIL JET

a.
A175161C01
1.99,0.5 2.375,0.719 0.385,0.219 10 false *a
*a Align


Align the groove on the cylinder block sub-assembly with the oil jet positioning bracket and tap in a new oil jet.

NOTICE:

Do not tap the tip of the oil jet.



Hide 11415 2.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.

Clean and degrease the cylinder block water drain cock sub-assembly and installation hole.


b.
A076531C06
2.365,1.302 2.25,0.99 false 2.302,1.333 2.615,1.49 0.313,0.156 10 false *a
*a Adhesive


Apply adhesive to the end 2 or 3 threads of the cylinder block water drain cock sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.
A300591

Using a 14 mm deep socket wrench, install the cylinder block water drain cock sub-assembly to the cylinder block sub-assembly.(*1)

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


d.
A302049E01
1.323,1.781 1.604,1.948 0.281,0.167 10 false 40° 1.938,1.792 2.219,1.958 0.281,0.167 10 false 40°

After applying the specified torque, rotate the cylinder block water drain cock sub-assembly clockwise until the drain port faces downward.

NOTICE:
·

Do not rotate the cylinder block water drain cock sub-assembly more than 360° in step (*1), and never loosen it after setting the cylinder block water drain cock sub-assembly correctly.

·

Do not fill the engine coolant for at least 1 hour after installation.




Hide 11434C 3.INSTALL STRAIGHT PIN

a.

Using a plastic hammer, tap in 7 new straight pins to the specified protrusion height.

A154883C01
0.753,0.915 0.875,1.067 0.122,0.153 10 A 2.894,1.52 3.016,1.673 0.122,0.153 10 A 0.695,3.079 0.818,3.232 0.122,0.153 10 B 2.965,3.947 3.087,4.1 0.122,0.153 10 B 4.621,1.817 4.744,1.97 0.122,0.153 10 C 6.387,3.681 6.509,3.833 0.122,0.153 10 D 4.548,3.198 4.67,3.35 0.122,0.153 10 D 2.367,5.303 2.998,5.453 0.631,0.151 10 8.5 to 9.5 2.367,7.005 3.158,7.162 0.791,0.158 10 18.5 to 19.5 5.264,5.311 5.874,5.462 0.61,0.151 10 8.5 to 9.5 5.25,7.14 6.011,7.299 0.761,0.159 10 11.5 to 12.5 1.618,6.023 2.038,6.194 0.42,0.171 10 A (φ8) 4.5,6.023 4.92,6.194 0.42,0.171 10 B (φ8) 1.618,8.164 2.118,8.335 0.5,0.171 10 C (φ10) 4.5,7.933 4.998,8.104 0.498,0.171 10 D (φ10) 6.337,8.122 6.603,8.283 0.267,0.161 10 mm 5.325,0.386 5.523,0.57 0.198,0.184 10 *b 5.325,2.356 5.523,2.54 0.198,0.184 10 *d 1.83,2.356 2.028,2.54 0.198,0.184 10 *c 1.83,0.386 2.028,0.57 0.198,0.184 10 *a
*a Upper Side *b Front Side
*c Lower Side *d Rear Side


Protrusion height:
Straight pin A:

8.5 to 9.5 mm (0.335 to 0.374 in.)

Straight pin B:

8.5 to 9.5 mm (0.335 to 0.374 in.)

Straight pin C:

18.5 to 19.5 mm (0.728 to 0.768 in.)

Straight pin D:

11.5 to 12.5 mm (0.453 to 0.492 in.)



Hide 15100A 4.INSTALL OIL PUMP SET RING PIN

a.
A105859E01
2.333,2.385 3.333,2.563 1,0.177 10 false 3.5 to 4.5 mm

Using a plastic hammer, tap in 2 new oil pump set ring pins to the specified protrusion height.

Protrusion height:

3.5 to 4.5 mm (0.138 to 0.177 in.)



Hide 5.INSTALL STUD BOLT

a.

Using an E5 and E7 "TORX" wrench, install the 7 stud bolts to the cylinder block sub-assembly.

A300622C01
1.427,1.583 1.219,0.802 1.219,0.802 1.604,1.615 true 2.229,1.156 2.396,0.792 true 1.385,2.063 2.115,2.406 2.115,2.406 1.667,1.708 true 6.302,2.063 6.719,1.302 6.719,1.302 5.677,1.792 true 0.729,0.354 0.927,0.531 0.198,0.177 10 false *a 1.063,0.708 1.26,0.885 0.198,0.177 10 false B 2.448,0.688 2.646,0.865 0.198,0.177 10 false C 2.188,2.396 2.385,2.573 0.198,0.177 10 false A 4.073,0.385 4.271,0.563 0.198,0.177 10 false *b 6.76,1.208 6.958,1.385 0.198,0.177 10 false D 0.396,4.344 0.896,4.51 0.5,0.167 10 false (1.142) 0.417,4.156 0.729,4.354 0.313,0.198 10 false 29 1.51,3.938 1.823,4.135 0.313,0.198 10 false 12 1.542,4.49 1.854,4.688 0.313,0.198 10 false 9.0 2.094,4.271 2.406,4.469 0.313,0.198 10 false 23 1.542,4.667 2.042,4.833 0.5,0.167 10 false (0.354) 2.063,4.438 2.563,4.604 0.5,0.167 10 false (0.906) 3.177,4.177 3.49,4.375 0.313,0.198 10 false 12 1.531,4.104 2.031,4.271 0.5,0.167 10 false (0.472) 3.177,4.323 3.677,4.49 0.5,0.167 10 false (0.472) 3.188,4.573 3.5,4.771 0.313,0.198 10 false 9.0 3.188,4.729 3.688,4.896 0.5,0.167 10 false (0.354) 3.708,3.802 4.021,4 0.313,0.198 10 false 48 3.677,3.958 4.177,4.125 0.5,0.167 10 false (1.890) 4.958,3.417 5.271,3.615 0.313,0.198 10 false 15 4.958,3.604 5.458,3.771 0.5,0.167 10 false (0.591) 4.948,4.271 5.26,4.469 0.313,0.198 10 false 10 4.958,4.438 5.458,4.604 0.5,0.167 10 false (0.394) 5.396,3.906 5.708,4.104 0.313,0.198 10 false 43.5 5.396,4.073 5.896,4.24 0.5,0.167 10 false (1.713) 6.49,3.51 6.802,3.708 0.313,0.198 10 false 12 6.5,3.677 7,3.844 0.5,0.167 10 false (0.472) 6.51,4.458 6.823,4.656 0.313,0.198 10 false 12 6.521,4.625 7.021,4.792 0.5,0.167 10 false (0.472) 6.469,5.104 6.75,5.26 0.281,0.156 10 false mm 6.479,5.25 6.896,5.427 0.417,0.177 10 false (in.) 1.083,4.906 1.24,5.104 0.156,0.198 10 false A 2.708,4.896 2.865,5.094 0.156,0.198 10 false B 4.417,4.917 4.573,5.115 0.156,0.198 10 false C 6.083,4.917 6.24,5.115 0.156,0.198 10 false D
*a Intake Side *b Front Side


Torque:
Stud bolt A, B and D : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
Stud bolt C : 11 N*m (112 kgf*cm, 8 ft.*lbf)

NOTICE:

The lower threads of the stud bolt are installed into the cylinder block sub-assembly.



Hide 11711 6.INSTALL CRANKSHAFT BEARING

A117086C01
2.119,2.737 2.303,2.907 0.184,0.17 10 *b 1.144,2.737 1.328,2.907 0.184,0.17 10 *a
*a Incorrect
*b Correct


a.

Align the crankshaft bearing (upper) with the oil hole of the cylinder block sub-assembly and install the crankshaft bearing.

NOTICE:

Do not apply engine oil to the crankshaft bearing or its contact surface.



b.
A117087E01
0.601,0.462 0.722,0.619 0.121,0.156 10 A 0.601,1.439 0.722,1.595 0.121,0.156 10 B

Align the crankshaft bearing (lower) with the crankshaft bearing cap and install the crankshaft bearing cap.

NOTICE:
·

Install the crankshaft bearing cap so that the gap between A and B is 0 to 0.4 mm (0 to 0.016 in.).

·

Do not apply engine oil to the crankshaft bearing or its contact surface.




Hide 11791 7.INSTALL UPPER CRANKSHAFT THRUST WASHER

A302050

a.

Install the 2 upper crankshaft thrust washers to the No. 3 journal position of the cylinder block sub-assembly with the oil grooves facing outward.


b.

Apply engine oil to the crankshaft bearing (upper) and install the crankshaft to the cylinder block sub-assembly.


Hide 13411 8.INSTALL CRANKSHAFT

A267077C07
0.688,0.813 0.885,0.49 true 1.021,0.969 1.344,0.708 true 2.344,0.823 2.542,0.5 true 0.927,0.365 1.094,0.521 0.167,0.156 10 false *a 2.604,0.375 2.771,0.531 0.167,0.156 10 false *c 1.427,0.615 1.604,0.771 0.177,0.156 10 false *b 0.063,0.083 0.26,0.24 0.198,0.156 10 false *1 1.844,0.063 2.021,0.219 0.177,0.156 10 false *2
*1 No. 3 Crankshaft Bearing Cap
*2 No. 1, 2, 4, 5 Crankshaft Bearing Cap
*a Front Mark
*b Number
*c Front Mark and Number


a.

Examine the front marks and numbers and install the 5 crankshaft bearing caps to the cylinder block sub-assembly.


b.

Apply a light coat of engine oil to the threads of the crankshaft bearing cap set bolts.


c.
A302806E02
1.563,0.406 1.75,0.573 0.188,0.167 10 true 1 0.958,0.396 1.167,0.552 0.208,0.156 10 true 5 0.26,0.375 0.469,0.552 0.208,0.177 10 true 9 2.813,0.417 3.021,0.594 0.208,0.177 10 true 7 2.198,0.385 2.406,0.563 0.208,0.177 10 true 3 1.573,1.677 1.729,1.865 0.156,0.188 10 true 2 0.927,1.656 1.083,1.844 0.156,0.188 10 true 6 0.271,1.656 0.479,1.844 0.208,0.188 10 true 10 2.833,1.656 3.042,1.844 0.208,0.188 10 true 8 2.208,1.667 2.417,1.854 0.208,0.188 10 true 4

Tighten the crankshaft bearing cap bolts in several steps to the specified torque in the sequence shown in the illustration. (*1)

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)

NOTICE:

Check that the crankshaft turns smoothly.



d.
A302031C05
2.26,0.51 2.646,0.25 true 2.688,0.177 2.927,0.354 0.24,0.177 10 false *a 1.177,0.24 1.417,0.417 0.24,0.177 10 false 90°
*a Paint Mark
V100136

Engine Front


Mark the front of the crankshaft bearing cap set bolts with paint.


e.

Further tighten the crankshaft bearing cap set bolts by 90° in the same sequence as step (*1).


f.

Check that the painted mark is now at a 90° angle from the front.


Hide 9.INSPECT CRANKSHAFT THRUST CLEARANCE

Hide 13101 10.INSTALL PISTON WITH PIN SUB-ASSEMBLY

a.
A249224C01
0.958,0.438 0.771,0.854 0.771,0.854 1.104,1.583 true 0.573,0.771 0.74,0.938 0.167,0.167 10 false *a
*a Front Mark


Coat the piston pin and pin holes in the piston with engine oil.


b.

Align the cavity of the piston with the protruding portion on the connecting rod.


c.

Using SST, press in the piston pin.

A302810C01
1.052,0.854 1.333,0.854 false 1.063,1.438 1.344,1.438 false 0.75,2.146 1.031,2.146 false 3.021,0.635 3.302,0.635 false 3.115,2.125 3.396,2.125 false 5.083,0.938 5.479,0.938 true 5.677,0.521 6.073,0.521 true 5.958,0.958 6.354,0.958 true 4.927,0.854 5.24,1.01 0.313,0.156 10 false *1 6.135,0.458 6.448,0.615 0.313,0.156 10 false *2 6.396,0.885 6.708,1.042 0.313,0.156 10 false *3 0.75,0.771 1.073,0.938 0.323,0.167 10 false SST 0.771,1.344 1.094,1.51 0.323,0.167 10 false SST 0.458,2.063 0.781,2.229 0.323,0.167 10 false SST 3.365,0.563 3.688,0.729 0.323,0.167 10 false SST 3.438,2.052 3.76,2.219 0.323,0.167 10 false SST
*1 Connecting Rod *2 Piston Pin
*3 Piston - -


SST
09221-25026  (09221-00021, 09221-00030, 09221-00150, 09221-00090, 09221-00100)


Hide 13041 11.INSTALL CONNECTING ROD BEARING

a.
A302052C01
2.458,0.573 1.958,0.198 true 1.802,0.094 2.021,0.271 0.219,0.177 10 false *a
*a Claw


Align the bearing claw with the groove of the connecting rod or connecting rod cap.

NOTICE:

Clean the back side of the bearing and bearing surface of the connecting rod and keep them free of oil.



Hide 13011 12.INSTALL PISTON RING SET

A302053C01
2.563,0.177 2.885,0.375 0.323,0.198 10 false *1
*1 No. 2 Compression Ring


HINT:

When reusing the piston rings, install them to the matched pistons with the surfaces facing correctly.


a.

Install the oil ring and 2 side rails by hand.


b.

Using a piston ring expander, install the No. 2 compression ring and No. 1 compression ring.

HINT:

When reusing the piston rings, install them to the matched pistons with the surfaces facing in the correct direction.



c.
A249063C01
2.625,0.146 2.792,0.313 0.167,0.167 10 false *2 2.635,1.719 2.802,1.885 0.167,0.167 10 false *4 1.083,1.719 1.25,1.885 0.167,0.167 10 false *3 1.073,0.146 1.24,0.313 0.167,0.167 10 false *1
*1 No. 1 Compression Ring and Oil Ring
*2 Side Rail (Lower)
*3 Side Rail (Upper )
*4 No. 2 Compression Ring
V100135

Engine Front


Position the piston rings so that the ring ends are as shown inthe illustration.


Hide 13.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, pistons, and surfaces of connecting rod bearings.


b.

Check the position of the piston ring ends.


c.
A302054C01
0.833,0.594 0.469,0.844 true 0.365,0.854 0.615,1.031 0.25,0.177 10 false *a
*a Front Mark


Using a piston ring compressor, push the correctly numbered piston and connecting rod assemblies into each cylinder with the front mark on the piston facing forward.

NOTICE:
·

Clean the back side of the bearing and bearing surface of the connecting rod cap and keep them free of oil.

·

Match the numbered connecting rod cap with the connecting rod.




d.
A302029C02
1.365,0.885 0.76,0.333 true 0.594,0.229 0.802,0.385 0.208,0.156 10 false *a
*a Front Mark


Make sure that the connecting rod and connecting rod cap are in the correct combination and that the front mark of the connecting rod cap is facing in the correct mounting orientation, then install the connecting rod cap to the connecting rod.


e.

Apply a light coat of engine oil to the threads of the connecting rod bolts.


f.
A302030E02
1.677,0.656 0.99,0.323 true 0.708,0.25 1.042,0.417 0.333,0.167 10 false SST

Using SST, tighten the connecting rod bolts in several steps to the specified torque.

SST
09205-16011  

Torque:
15 N*m (153 kgf*cm, 11 ft.*lbf)


g.
A302031C05
2.26,0.51 2.646,0.25 true 2.688,0.177 2.927,0.354 0.24,0.177 10 false *a 1.177,0.24 1.417,0.417 0.24,0.177 10 false 90°
*a Paint Mark
V100136

Engine Front


Mark the front of the connecting rod bolts with paint.


h.

Further tighten the connecting rod bolts by 90° as shown inthe illustration.


i.

Check that the crankshaft turns smoothly.


Hide 14.INSPECT CONNECTING ROD THRUST CLEARANCE