Home › Engine / Hybrid System › 2NZ-FE ENGINE MECHANICAL › DRIVE BELT › 2013.08–2016.07
RM30M0E _51 Engine / Hybrid System _017074 2NZ-FE ENGINE MECHANICAL _0091011 DRIVE BELT G

2NZ-FE ENGINE MECHANICAL  DRIVE BELT  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 16361A 1.INSPECT FAN AND GENERATOR V BELT

A219362

a.

Check the fan and generator V belt for wear, cracks or other signs of damage.

If any of the following defects is found, replace the fan and generator V belt.

·

The fan and generator V belt is cracked.

·

The fan and generator V belt is worn out to the extent that the cords are exposed.

·

The fan and generator V belt has chunks missing from the ribs.



b.
A304759C01
0.698,1.385 1.01,1.542 0.313,0.156 10 false *a 2.26,1.406 2.573,1.563 0.313,0.156 10 false *b
*a Correct
*b Incorrect


Check that the fan and generator V belt fits properly in the ribbed grooves.

HINT:

Check with your hand to confirm that the fan and generator V belt has not slipped out of the grooves on the bottom of the pulley. If it has slipped out, replace the fan and generator V belt. Install a new fan and generator V belt correctly.



c.
A116200
1.104,1.771 1.417,1.667 true 2.302,0.667 2.615,0.563 true 2.323,1.302 2.635,1.198 true 2.417,4.031 2.729,3.927 true 1.063,3.823 1.375,3.719 true 2.313,2.688 2.625,2.583 true 2.302,3.323 2.615,3.219 true 0.115,2.24 0.323,2.417 0.208,0.177 12 false *B 0.104,0.125 0.417,0.281 0.313,0.156 12 false *A 0.896,1.688 1.104,1.854 0.208,0.167 10 false *1 2.656,0.479 2.969,0.635 0.313,0.156 10 false *2 2.688,1.115 3,1.271 0.313,0.156 10 false *3 2.792,3.844 3.104,4 0.313,0.156 10 false *4 0.885,3.76 1.094,3.927 0.208,0.167 10 false *1 2.688,2.51 3,2.667 0.313,0.156 10 false *2 2.688,3.135 3,3.292 0.313,0.156 10 false *3
*A w/o Air Conditioning System
*B w/ Air Conditioning System
*1 Crankshaft Damper Sub-assembly
*2 Generator with Regulator Assembly
*3 Engine Water Pump Assembly
*4 Cooler Compressor Assembly
V100135

Specified Point


Inspect the fan and generator V belt deflection and tension.

Deflection:
Item Specified Condition
New belt 8.0 to 9.0 mm (0.31 to 0.35 in)
Used belt 12.5 to 13.5 mm (0.49 to 0.53 in)


Tension:
Item Specified Condition
New belt 700 to 800 N (71 to 82 kg, 157 to 180 lb)
Used belt 300 to 400 N (31 to 41 kg, 67 to 90 lb)


If the fan and generator V belt deflection is not as specified, adjust it.

HINT:
·

When inspecting the fan and generator V belt deflection, apply 98 N (10 kgf) tensile force to it.

·

Perform the fan and generator V belt inspection and adjustment while the engine is cold.

·

The fan and generator V belt tension and deflection should be checked immediately after installation of a new fan and generator V belt, and after cranking the engine when inspecting a used belt.

·

Check the fan and generator V belt deflection at the point between the specified pulleys where the deflection is greatest.

·

When installing a new fan and generator V belt, set its tension to the intermediate value of the specification.

·

When inspecting a fan and generator V belt which has been used for over 5 minutes, apply the Used Belt specifications.

·

When reinstalling a fan and generator V belt which has been used for over 5 minutes, adjust its deflection and tension to the intermediate values of each Used Belt specification.

·

The fan and generator V belt tension and deflection should be checked after 2 revolutions of engine cranking.

·

When using a belt tension gauge, confirm its accuracy by using a master gauge first.