Home › Drivetrain › C50 MANUAL TRANSMISSION / TRANSAXLE › SHIFT AND SELECT LEVER SHAFT(for 1NZ-FE) › 2013.08–2016.07
RM30M0E _52 Drivetrain _017090 C50 MANUAL TRANSMISSION / TRANSAXLE _0091176 SHIFT AND SELECT LEVER SHAFT(for 1NZ-FE) A

C50 MANUAL TRANSMISSION / TRANSAXLE  SHIFT AND SELECT LEVER SHAFT(for 1NZ-FE)  REASSEMBLY  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

All disassembled parts should be cleaned before reassembly.

·

Coat all of the sliding and rotating surfaces with gear oil before reassembly, and check that they move smoothly after reassembly.



Hide 33276H 2.INSTALL NO. 1 SELECT SPRING SEAT SHAFT SNAP RING

a.
C120738

Coat the shift and select lever shaft with gear oil.


b.

Using a brass bar and a hammer, install a new No. 1 select spring seat shaft snap ring to the shift and select lever shaft.


Hide 33256 3.INSTALL SELECT INNER LEVER

a.
C157382C01
3.063,1.073 3.375,1.271 0.313,0.198 10 false *a
*a Drive in Depth


Coat the No. 1 select spring seat with gear oil.


b.

Using a 5 mm pin punch and a hammer, install the No. 1 select spring seat, compression spring, select inner lever and the select inner lever slotted spring pin to the shift and select lever shaft.

Driven in depth:

3.0 to 4.0 mm (0.119 to 0.157 in.)



Hide 33251A 4.INSTALL INNER NO. 1 SHIFT LEVER

a.
C286556C01
3.104,0.781 3.302,0.979 0.198,0.198 10 false *a
*a Drive in Depth


Coat the shift interlock plate and the inner No. 1 shift lever with gear oil.


b.

Using a 5 mm pin punch and a hammer, install the shift interlock plate, inner No. 1 shift lever and the inner No. 1 shift lever slotted spring pin to the shift and select lever shaft.

Driven in depth:

-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)



Hide 33252A 5.INSTALL INNER NO. 2 SHIFT LEVER

a.
C157384C01
3.198,0.74 3.385,0.938 0.188,0.198 10 false *a
*a Drive in Depth


Coat the inner No. 2 shift lever with gear oil.


b.

Using a 5 mm pin punch and a hammer, install the inner No. 2 shift lever and the inner No. 2 shift lever slotted spring pin to the shift and select lever shaft.

Driven in depth:

1.0 to 2.0 mm (0.0394 to 0.0787 in.)



Hide 33277 6.INSTALL NO. 2 SELECT SPRING SEAT

a.
C286562

Coat the No. 2 select spring seat with gear oil.


b.

Install the No. 2 select spring seat and the compression spring to the shift and select lever shaft.


c.

Using a brass bar and a hammer, install a new E-ring to the shift and select lever shaft.


Hide 33520A 7.INSTALL FLOOR SHIFT CONTROL SHAFT ASSEMBLY

a.
C264878

Install the floor shift control shaft assembly to the selecting bellcrank support with the nut.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 33534F 8.INSTALL NO. 2 SELECTING BELLCRANK BUSH

a.
C155101

Install 2 new No. 2 selecting bellcrank bushes to the selecting bellcrank support.


b.

Coat the No. 2 selecting bellcrank bushes with MP grease.


Hide 33558 9.INSTALL NO. 2 SELECTING BELLCRANK DUST COVER

a.
C264877C01
1.365,1.719 1.76,1.917 true 1.792,1.833 1.979,2.01 0.188,0.177 10 false *a
*a Arrow Mark


Install the No. 2 selecting bellcrank dust cover to the selecting bellcrank support.

HINT:

Position the arrow mark as shown in the illustration.



Hide 33534E 10.INSTALL NO. 2 SELECTING BELLCRANK

a.
C293457

Install the No. 2 selecting bellcrank to the selecting bellcrank support.


Hide 33534G 11.INSTALL NO. 2 SELECTING BELLCRANK PLATE WASHER

a.
C264875

Install the No. 2 selecting bellcrank plate washer to the No. 2 selecting bellcrank with the nut.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 33557A 12.INSTALL NO. 1 SELECTING BELLCRANK DUST COVER

a.
C264874

Install the No. 1 selecting bellcrank dust cover to the selecting bellcrank support.


Hide 33557F 13.INSTALL FLOOR SHIFT CONTROL BELLCRANK DUST COVER

a.
C264873

Install the floor shift control bellcrank dust cover to the selecting bellcrank support.