Home › Drivetrain › C50 MANUAL TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › 2013.08–2017.10
RM30M0E _52 Drivetrain _017090 C50 MANUAL TRANSMISSION / TRANSAXLE _0091177 DIFFERENTIAL CASE A

C50 MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

All disassembled parts should be cleaned before reassembly.

·

Coat all of the sliding and rotating surfaces with gear oil before reassembly, and check that they move smoothly after reassembly.



Hide 41331F 2.INSTALL FRONT DIFFERENTIAL SIDE GEAR

a.
C283051

Coat the sliding and rotating surfaces of the 2 front differential side gears, 2 front differential side gear thrust washers, 2 front differential pinions and the 2 front differential pinion thrust washers with gear oil.


b.

Install the 2 front differential side gear thrust washers to the 2 front differential side gears.


c.

Install the 2 front differential side gears, 2 front differential pinions and the 2 front differential pinion thrust washers to the front differential case.

HINT:

Rotating each front differential side gear, install the 2 front differential pinions and the 2 front differential pinion thrust washers.



Hide 41342F 3.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C283050

Coat the front No. 1 differential pinion shaft with gear oil.


b.

Install the front No. 1 differential pinion shaft to the front differential case so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front differential case.


Hide 4.ADJUST FRONT DIFFERENTIAL SIDE GEAR BACKLASH

a.
C283047

Using a dial indicator, measure the front differential side gear backlash while holding one of the front differential pinions toward the front differential case.

Standard backlash:

0.05 to 0.20 mm (0.00197 to 0.00787 in.)


If the backlash is not as specified, replace the front differential side gear thrust washers.

Front Differential Side Gear Thrust Washer Thickness:
Part No. Thickness
mm (in.)
41361-22140 0.95 (0.0374)
41361-22020 1.00 (0.0394)
41361-22150 1.05 (0.0413)
41361-22030 1.10 (0.0433)
41361-22160 1.15 (0.0452)
41361-22040 1.20 (0.0472)


HINT:
·

Measure the thickness with a micrometer to select a proper thrust washer because the thrust washers do not have any distinguishing marks.

·

Select thrust washers of the same thickness for both the right and left sides.




Hide 41342A 5.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C283058

Using a 5 mm pin punch and a hammer, install the front differential pinion shaft straight pin to the front differential case.


b.
C288397

Using a chisel and a hammer, stake the front differential case hole.


Hide 41221 6.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
C166738C01
1.063,0.417 1.281,0.615 0.219,0.198 10 false *a
*a 90 to 110°C (194 to 230°F)


Using a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

CAUTION:

Use thick gloves to protect your hands as the front differential ring gear is hot.


NOTICE:

Do not heat the ring gear to more than 110°C (230°F).



b.

Clean the contact surfaces of the front differential case and the front differential ring gear.


c.
C283046
1.688,0.833 0.896,0.833 0.896,0.833 1.635,0.781 true 0.719,0.75 1.031,0.948 0.313,0.198 10 false *a
*a Matchmark


After moisture on the front differential ring gear has completely evaporated, align the matchmarks on the front differential ring gear and the front differential case, and quickly install them.


d.

Secure the front differential case in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.

Install the 8 bolts.

Torque:
77.4 N*m (789 kgf*cm, 57 ft.*lbf)

NOTICE:
·

Do not wash the bolts in an alkaline substance.

·

Tighten the bolts after the front differential ring gear has cooled down sufficiently.




Hide 33481X 7.INSTALL SPEEDOMETER DRIVE GEAR

a.
C283044

Install the speedometer drive gear to the front differential case.