Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › IGNITION SYSTEM › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017072 2NZ-FE ENGINE CONTROL _0091217 IGNITION SYSTEM G

2NZ-FE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.PERFORM SPARK TEST

a.

Check for DTCs.


NOTICE:

If any DTC is present, perform troubleshooting in accordance with the procedure for that DTC.



b.
A156076

Disconnect the 4 fuel injector assembly connectors.


c.

Remove the 4 No. 1 ignition coils and 4 spark plugs.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL


d.
A283545

Install a spark plug to each No. 1 ignition coil and connect the No. 1 ignition coil connectors.


e.

Ground the spark plugs.


f.

Check that sparks occur while the engine is being cranked.


g.

Check whether sparks occur.

NOTICE:
·

Ground the spark plugs when checking them.

·

Replace any No. 1 ignition coils that have been subjected to a physical impact.

·

Do not crank the engine for more than 2 seconds.




h.

If spark does not occur, perform the following procedure.


Hide 2.INSPECT IGNITION COIL AND SPARK TEST

a.

Perform the spark test in accordance with the following procedure.

i.

Check that the wire harness side connector of the No. 1 ignition coil is securely connected.

Result:
Result Proceed to
OK Go to next step
NG Connect securely



b.

Perform a spark test on each No. 1 ignition coil.

i.

If there is a cylinder where sparks do not occur, replace its No. 1 ignition coil with the No. 1 ignition coil of a cylinder where sparks occur normally.


ii.

Crank the engine and visually check that sparks occur at the cylinder with the normally operating No. 1 ignition coil.

Result:
Result Proceed to
OK Go to next step
NG Replace No. 1 ignition coil



c.

Perform a spark test on each spark plug.

i.

If there is a cylinder where sparks do not occur, replace its spark plug with the spark plug of a cylinder where sparks occur normally.


ii.

Crank the engine and visually check that sparks occur at the cylinder with the normally operating spark plug.

Result:
Result Proceed to
OK Replace spark plug
NG Inspect the ignition system
·

for Automatic Transaxle:

Click here(Click here)

·

for Manual Transaxle:

Click here(Click here)





d.

Install the 4 No. 1 ignition coils and 4 spark plugs.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION


e.

Connect the 4 fuel injector assembly connectors.


Hide 19100P 3.INSPECT SPARK PLUG

NOTICE:
·

Do not use a wire brush for cleaning.

·

Do not attempt to adjust the electrode gap of a used spark plug.



a.
I109591C02
0.719,2 1.073,1.969 false 0.552,1.927 0.865,2.083 0.313,0.156 10 false *a
*a Ground


Check the electrode.

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance:
Tester Connection Condition Specified Condition
Spark plug (Terminal part) - Ground Always 10 MΩ or higher


HINT:
·

If the result is not as specified, clean the spark plug with a spark plug cleaner and measure the resistance again.

·

If a megohmmeter is not available, perform the following simple inspection instead.





b.

Alternative inspection method:

NOTICE:

Do not perform this step when any of the following DTCs are output; P0300, P0301, P0302, P0303, P0304 (Cylinder Misfire Detected)


i.

Start the engine.


ii.

Quickly accelerate the engine to 4000 rpm 5 times.


iii.

Remove the spark plug.


iv.
P003783

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage to its thread and insulator.

If there is any damage, replace the spark plug.

Recommended Spark Plug:
Manufacturer Product
DENSO K16R-U11
NGK BKR5EYA-11



d.
A122451C01
2.938,1.24 3.25,1.396 0.313,0.156 10 false *a
*a Electrode Gap


Reference:

i.

Check the spark plug electrode gap.

Maximum electrode gap for a used spark plug:

1.3 mm (0.0512 in.)


If the electrode gap is more than the maximum, replace the spark plug.

Electrode gap for a new spark plug:

1.0 to 1.1 mm (0.0394 to 0.0433 in.)


NOTICE:

Never attempt to adjust the electrode gap of a used spark plug.




e.
A296690C01
2.073,1.677 2.438,1.813 false 2.49,1.75 2.802,1.906 0.313,0.156 10 false *a
*a Spark Plug Cleaner


Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.

Standard air pressure:

588 kPa (6 kgf/cm2, 85 psi)


Standard duration:

20 seconds or less


HINT:

Only use a spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.