Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)
RM30M0E _58 Vehicle Interior _017110 DOOR LOCK _0091390 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System) D

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Smart Entry and Start System)  DIAGNOSIS SYSTEM  


INSPECT BATTERY VOLTAGE


a.

Measure the vehicle battery voltage.

Standard voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery.



SELF-DIAGNOSTIC MODE (OPERATING IGNITION KEY CYLINDER)


a.

Switch to self-diagnostic mode.

i.

Insert the key into the ignition key cylinder and remove it.


ii.

Within 5 seconds after the key is removed, insert it into the ignition key cylinder and then turn the ignition switch ON then off 1 time. (End in off)


iii.

Within 30 seconds of turning the ignition switch off, perform the following 9 times: Turn the ignition switch ON then off. (End in off)

HINT:

Turning the ignition switch ON after the procedure above has been completed will end the self-diagnostic mode.


CAUTION:

If the system fails to enter the self-diagnostic mode, the system will return to normal mode.




b.
B220865E42
0.125,0.031 1.802,0.323 1.677,0.292 10 false Interior Light Output: 0.635,1.406 1.063,1.688 0.427,0.281 10 false ON 0.573,1.688 0.896,1.948 0.323,0.26 10 false OFF 1.552,2.167 1.917,2.5 0.365,0.333 10 false T1 2.146,2.167 2.604,2.604 0.458,0.438 10 false T2 1.979,2.604 3.427,3.042 1.448,0.438 10 false T1: 0.25 seconds 1.979,2.917 3.292,3.313 1.313,0.396 10 false T2: 0.5 seconds 1.802,2.167 2.125,2.51 0.323,0.344 10 false T1

Check that the system has switched to self-diagnostic mode by checking the interior light output pattern.


c.

Check the diagnostic outputs when a door control transmitter assembly switch is pressed. The diagnostic outputs can be checked by the interior light patterns.

B163380
0.115,0.063 1.604,0.323 1.49,0.26 10 false Interior Light Output: 0.292,1.344 1.979,1.625 1.688,0.281 10 false (Lock/Unlock Switch): 0.51,1.979 0.906,2.24 0.396,0.26 10 false ON 0.458,2.365 0.844,2.583 0.385,0.219 10 false OFF 4.125,0.563 6.51,0.938 2.385,0.375 10 false Unmatching Recognition Code (B): 4.26,1.156 4.583,1.385 0.323,0.229 10 false ON 4.208,1.552 4.74,1.906 0.531,0.354 10 false OFF 4.125,2.917 5.938,3.177 1.813,0.26 10 false No Diagnostic Output (C): 4.198,3.365 4.771,3.698 0.573,0.333 10 false OFF 1.25,2.802 1.563,3.01 0.313,0.208 10 false T1 1.76,2.802 2.146,3.063 0.385,0.26 10 false T2 4.938,2.031 6.604,2.344 1.667,0.313 10 false Wave is being received 0.594,3.469 2.979,3.813 2.385,0.344 10 false T1: 0.25 seconds (Interior Light) 0.594,3.896 2.969,4.25 2.375,0.354 10 false T2: 0.5 seconds (Interior Light) 0.292,1.031 1.542,1.281 1.25,0.25 10 false Normal Wave (A):

Result
Interior Light Output Suspected Area
A Normal (No malfunction)
B Unmatching register wireless code
C Wave interference or malfunction of a related component