1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK
Check fuel pump operation.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Do not start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump /Speed.
| Tester Display |
|---|
| Control the Fuel Pump / Speed |
Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank assembly can be heard. If no sounds can be heard, check the driver side junction block assembly, fuel pump, ECM and wiring connectors.
Inspect for fuel leaks.
Check for fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts if necessary.
Turn the ignition switch off.
Disconnect the GTS from the DLC3.
2.CHECK FUEL PRESSURE
Discharge the fuel system pressure.
Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL SYSTEM>PRECAUTION
Check the voltage.
Measure the battery voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Positive (+) terminal - Negative (-) terminal | Ignition switch off | 11 to 14 V |
Disconnect the cable from the negative (-) battery terminal.
Remove the EFI fuel pipe clamp.
Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL INJECTOR>REMOVAL
Disconnect the fuel tube sub-assembly.
Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL INJECTOR>REMOVAL
Install SST (pressure gauge) using other SST as shown in the illustration.
| *1 | Fuel Tube Sub-assembly | *2 | Fuel Delivery Pipe Sub-assembly |
| *a | SST (Hose Band) | *b | SST (T-joint) |
| *c | SST (Pressure Gauge) | *d | SST (Hose) |
| *e | SST (Fuel Tube Connector) | - | - |
Clean up any spilled gasoline.
Connect the cable to the negative (-) battery terminal.
Connect the GTS to the DLC3.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
| Tester Display |
|---|
| Control the Fuel Pump / Speed |
Measure the fuel pressure.
304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44.1 to 49.7 psi)
If the fuel pressure is greater than the standard value, replace the fuel pressure regulator assembly.
If the fuel pressure is less than the standard value, check the fuel hoses and connections, fuel pump, fuel pump filter and fuel pressure regulator assembly.
Disconnect the GTS from the DLC3.
Start the engine.
Measure the fuel pressure at idle.
304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44.1 to 49.7 psi)
Stop the engine.
Check that the fuel pressure remains as specified for 5 minutes after the engine stops.
147 kPa (1.5 kgf/cm2, 21 psi) or more
If the fuel pressure is not as specified, check the fuel pump, fuel pressure regulator assembly and fuel injector assembly.
After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST to prevent gasoline from spraying.
Connect the fuel tube sub-assembly.
Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL INJECTOR>INSTALLATION
Install the EFI fuel pipe clamp.
Click hereEngine / Hybrid System>2NZ-FE FUEL>FUEL INJECTOR>INSTALLATION
Check and clear for DTCs.
for Automatic Transaxle:
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>DTC CHECK / CLEAR
for Manual Transaxle:
Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>DTC CHECK / CLEAR
Inspect for fuel leaks.