Home › Engine / Hybrid System › 2NZ-FE COOLING › COOLANT › 2013.08–2016.07
RM30M0E _51 Engine / Hybrid System _017082 2NZ-FE COOLING _0092340 COOLANT A

2NZ-FE COOLING  COOLANT  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:

Be sure that the ignition switch is off if you work near the electric cooling fans or radiator grille. With the ignition switch ON, the electric cooling fans may automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

NOTICE:

To avoid the danger of being burned, do not remove the water filler cap sub-assembly while the engine and radiator assembly are still hot. Thermal expansion will cause hot engine coolant and steam to blow out from the radiator assembly.


A304787C02
1.698,0.927 2.5,0.49 true 0.625,2.948 1.042,2.5 true 2.552,0.375 2.865,0.531 0.313,0.156 10 false *1 0.448,2.875 0.76,3.031 0.313,0.156 10 false *2
*1 Water Filler Cap Sub-assembly
*2 Radiator Drain Cock Plug


a.

Loosen the radiator drain cock plug.


b.

Remove the water filler cap sub-assembly, then drain the engine coolant.


Hide 2.ADD ENGINE COOLANT

a.

Tighten the radiator drain cock plug by hand.


b.
A206788C11
2.719,0.865 2.896,0.604 false 2.208,1.573 2.469,1.792 false 2.938,0.5 3.25,0.656 0.313,0.156 10 false *a 2.521,1.729 2.833,1.885 0.313,0.156 10 false *b 2.75,1.135 3.063,1.292 0.313,0.156 10 false *c
*a Filler Tube End
*b Coolant Level
*c 20 mm (0.787 in.)


Slowly fill the radiator assembly with TOYOTA Super Long Life Coolant (SLLC) from the water filler. (Engine coolant level should be within 20 mm (0.787 in.) from the filler tube end.)

Capacity:
Transaxle Type Fan Shroud Ventilation Duct Coolant Capacity
Automatic Transaxle With 5.0 liters (5.3 US qts, 4.4 Imp. qts)
Without 4.6 liters (4.9 US qts, 4.0 Imp. qts)
Manual Transaxle With 5.0 liters (5.3 US qts, 4.4 Imp. qts)
Without 4.6 liters (4.9 US qts, 4.0 Imp. qts)


NOTICE:

Do not substitute water for engine coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate engine coolant with long-life hybrid organic acid technology (engine coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).



c.

Remove the reserve tank cap.


d.
A246002C06
2.188,1.667 2.51,1.49 true 2.094,0.99 2.479,0.781 true 2.552,0.688 2.865,0.844 0.313,0.156 10 false *a 2.563,1.385 2.875,1.542 0.313,0.156 10 false *b
*a Full Line
*b Low Line


Slowly pour engine coolant into the radiator reserve tank assembly until it reaches the full line.


e.

Install the water filler cap sub-assembly securely.


f.

Install the reserve tank cap.


g.

Bleed air from the cooling system.

i.

Warm up the engine until the thermostat opens.

While the thermostat is open, circulate the engine coolant for several minutes.

NOTICE:
·

Make sure that the radiator reserve tank assembly still has some engine coolant in it.


·

If the engine coolant temperature gauge indicates an excessive temperature, turn off the engine and let it cool.


·

If there is not enough engine coolant, the engine may overheat or be seriously damaged.


·

If the radiator reserve tank assembly does not have enough engine coolant, perform the following: stop the engine, wait until the engine coolant has cooled down and add engine coolant until the radiator reserve tank assembly is filled to the full line.



HINT:

The thermostat open timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.




h.

Stop the engine and wait until the engine coolant cools down.


i.

Recheck the engine coolant level inside the radiator reserve tank assembly. If it is below the full level, add engine coolant.