Home › Power Source / Network › 1NZ-FE BATTERY / CHARGING › GENERATOR › 2013.08–2016.10
RM30M0E _57 Power Source / Network _017107 1NZ-FE BATTERY / CHARGING _0090210 GENERATOR A

1NZ-FE BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27446A 1.REMOVE CLAMP

a.
A307906

Remove the bolt and clamp from the generator coil assembly.


Hide 27411 2.REMOVE GENERATOR PULLEY

a.

Secure the generator with regulator assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
A310428C01
2.396,1.26 2.51,1.115 false 2.917,1.635 3.188,0.958 true 2.417,0.156 2.969,0.75 true 2.698,1.688 3.271,1.875 0.573,0.188 10 false SST1-A 1.885,0.073 2.458,0.26 0.573,0.188 10 false SST1-B 2.323,1.292 2.635,1.49 0.313,0.198 10 false *1
*1 Generator Rotor Assembly Shaft


Install SST1-A and SST2-B to the generator rotor assembly shaft as shown in the illustration.

SST
09820-63011  (09820-06010)


c.
A307907C01
2.865,0.49 1.865,0.24 true 2.938,1.375 3.115,0.708 true 2.229,1.021 2.344,0.875 false 2.094,3.167 2.406,3.365 0.313,0.198 10 false *a 1.438,2.479 1.604,2.656 0.167,0.177 10 true *b 2.146,1.031 2.458,1.229 0.313,0.198 10 false *1 2.729,1.438 3.292,1.635 0.563,0.198 10 true SST1-A 1.333,0.146 1.896,0.344 0.563,0.198 10 false SST1-B
*1 Generator Rotor Assembly Shaft
*a Hold
*b Turn


Hold SST1-A with a torque wrench, and tighten SST1-B clockwise to the specified torque.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

NOTICE:

Check that SST is securely fitted onto the generator rotor assembly shaft.



d.
A307908E01
1.896,0.906 2.323,0.271 false 2.01,0.938 2.354,0.573 false 2.823,1.292 2.646,1.083 false 2.427,0.5 3,0.688 0.573,0.188 10 false SST1-A 2.385,0.188 2.958,0.375 0.573,0.188 10 false SST1-B 2.896,1.25 3.323,1.438 0.427,0.188 10 false SST2

Place SST2 to the nut.

SST
09820-63011  (09820-06021)

NOTICE:

Securely attach SST to the generator pulley and generator rotor assembly shaft.



e.
A307909C01
2.823,1.396 2.938,0.99 true 2.573,0.563 1.927,0.573 true 2.615,1.469 3.146,1.677 0.531,0.208 10 false SST1-A 1.521,0.5 1.948,0.698 0.427,0.198 10 false SST2 0.906,2.896 1.219,3.094 0.313,0.198 10 false *a 1.719,2.865 2.031,3.063 0.313,0.198 10 false *b
*a Hold
*b Turn


While holding SST2, turn SST1-A in the direction shown in the illustration to loosen the nut.

NOTICE:

To prevent damage to the generator rotor assembly shaft, do not loosen the nut by more than one half turn.



f.

Remove SST2 from the nut.


g.
A307910C01
2.875,1.333 3.094,0.74 true 1.844,0.156 2.865,0.5 true 2.646,1.406 3.229,1.604 0.583,0.198 10 false SST1-A 1.281,0.073 1.865,0.271 0.583,0.198 10 false SST1-B 2.198,3.125 2.51,3.323 0.313,0.198 10 false *a 1.438,2.74 1.75,2.938 0.313,0.198 10 false *b
*a Hold
*b Turn


Hold SST1-A, turn SST1-B in the direction shown in the illustration, and remove SST1-A and SST1-B from the generator rotor assembly shaft.


h.

Remove the nut and generator pulley from the generator rotor assembly shaft.


i.

Remove the generator with regulator assembly from the vise.


Hide 27039 3.REMOVE GENERATOR REAR END COVER

a.

Place the generator drive end frame assembly on the generator pulley.


b.
A307911

Remove the 3 bolts and generator rear end cover from the generator coil assembly.


Hide 27387B 4.REMOVE GENERATOR TERMINAL INSULATOR

a.
A307912

Remove the generator terminal insulator from the generator coil assembly.


Hide 27370A 5.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A307913

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 27360 6.REMOVE GENERATOR COIL ASSEMBLY

a.
A311767

Remove the 4 bolts from the generator coil assembly.


b.
A310423C01
0.625,1.833 1.031,2.031 true 2.323,0.781 2.833,0.854 false 1.094,1.969 1.479,2.125 0.385,0.156 10 false SST 2.906,0.75 3.292,0.906 0.385,0.156 10 false SST 0.146,0.771 0.458,0.969 0.313,0.198 10 false *a 2.906,0.156 3.219,0.354 0.313,0.198 10 false *b
*a Hold
*b Turn


Using SST, remove the generator coil assembly from the generator drive end frame assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)
09950-60010  (09951-00250)

NOTICE:

Apply grease to the threads and tip of the SST center bolt before use.



c.
A310405

Remove the generator bearing cover packing from the generator coil assembly.

NOTICE:

If the generator bearing cover packing breaks, remove broken pieces completely.


HINT:

The generator bearing cover packing may be installed on the generator rotor assembly.



Hide 27330 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A310406

Remove the generator rotor assembly from the generator drive end frame assembly.

NOTICE:

Do not drop the generator rotor assembly.



Hide 8.INSPECT GENERATOR DRIVE END FRAME BEARING

a.
A310422

Check that the generator drive end frame bearing is not rough or worn.

If the generator drive end frame bearing does not rotate smoothly, replace the generator rotor assembly.


Hide 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A310407

Remove the 4 screws and retainer plate from the generator drive end frame assembly.


b.
A310408E01
2.573,1.313 2.333,0.896 2.333,0.896 2.635,1.063 true 1.208,1.521 0.677,1.885 0.677,1.885 1.219,1.354 true 2.208,0.719 2.594,0.896 0.385,0.177 10 false SST 0.542,1.906 0.927,2.083 0.385,0.177 10 false SST

Using SST and a hammer, tap out the generator drive end frame bearing from the generator drive end frame assembly.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)