Home › Power Source / Network › 1NZ-FE BATTERY / CHARGING › GENERATOR › 2013.08–2016.10
RM30M0E _57 Power Source / Network _017107 1NZ-FE BATTERY / CHARGING _0090210 GENERATOR A

1NZ-FE BATTERY / CHARGING  GENERATOR  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL GENERATOR DRIVE END FRAME BEARING

a.
A310415E01
1.073,1.24 0.458,0.333 0.458,0.333 1.104,0.854 true 2.563,0.521 2.823,0.354 2.823,0.354 2.677,0.75 false 0.146,0.24 0.604,0.438 0.458,0.198 10 false SST 2.906,0.25 3.24,0.448 0.333,0.198 10 false SST

Using SST and a press, press in a new generator drive end frame bearing to the generator end frame assembly until the bearing surface is level with the frame surface.

SST
09950-60010  (09951-00470)
09950-70010  (09951-07100)


b.
A310416C01
2.365,1.833 2.646,1.583 true 2.531,1.052 2.885,0.24 true 2.917,0.125 3.229,0.323 0.313,0.198 10 false *a 2.188,1.823 2.5,2.021 0.313,0.198 10 false *b
*a Tab
*b Cutout


Fit the tabs on the retainer plate into the cutouts on the generator drive end frame assembly.


c.

Install the retainer plate to the generator drive end frame assembly with the 4 screws.

Torque:
2.3 N*m (23 kgf*cm, 20 in.*lbf)


Hide 27330 2.INSTALL GENERATOR ROTOR ASSEMBLY

A310406

a.

Place the generator drive end frame assembly on the generator pulley.


b.

Install the generator rotor assembly to the generator drive end frame assembly.


Hide 27360 3.INSTALL GENERATOR COIL ASSEMBLY

a.
A310446C01
0.792,2.823 1.552,2.729 true 1.677,2.927 2.438,2.833 true 2.844,0.833 3.146,2.031 true 2.188,0.177 2.74,0.594 true 0.635,0.552 1.219,0.208 true 0.521,0.74 0.167,1.948 true 0.615,2.74 0.927,2.938 0.313,0.198 10 false *a 2.51,2.771 2.823,2.969 0.313,0.198 10 false *b 3.083,2.094 3.333,2.292 0.25,0.198 10 false *b 2.01,0.073 2.323,0.271 0.313,0.198 10 false *a 1.26,0.104 1.573,0.302 0.313,0.198 10 false *a 0.104,2 0.385,2.385 0.281,0.385 10 true *b
*a Protrusion
*b Groove


Install a new generator bearing cover packing to the generator coil assembly.

HINT:

Align the 3 protrusions of the generator bearing cover packing with the 3 grooves of the generator coil assembly when installing.



b.
A307914

Temporarily install the generator coil assembly to the generator drive end frame assembly with the 4 bolts.


c.
A310417E01
1.344,0.49 0.802,0.365 false 2.854,0.281 2.688,0.49 false 0.469,0.281 0.813,0.448 0.344,0.167 10 false SST 2.917,0.198 3.26,0.365 0.344,0.167 10 false SST

Using SST and a press, slowly press the generator coil assembly to install it.

SST
09612-70100  (09612-07240)


d.

Tighten the 4 bolts.

Torque:
5.6 N*m (57 kgf*cm, 50 in.*lbf)


Hide 27370A 4.INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

a.
A310418C01
0.948,0.667 1.188,0.354 false 2.135,1.792 2.49,1.385 true 1.24,0.24 1.552,0.438 0.313,0.198 10 false *a 1.958,1.698 2.271,1.896 0.313,0.198 10 false *a
*a 1.0 mm (0.0394 in.) Diameter Pin


While pushing the 2 brushes into the generator brush holder assembly, insert a 1.0 mm (0.0394 in.) diameter pin into the generator brush holder assembly hole.


b.
A310419

Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

Torque:
1.8 N*m (18 kgf*cm, 16 in.*lbf)


c.
A310420C01
1.74,0.635 2.688,0.271 true 2.76,0.156 3.073,0.354 0.313,0.198 10 false *a
*a 1.0 mm (0.0394 in.) Diameter Pin
V100135

Pull Out


Pull out the 1.0 mm (0.0394 in.) diameter pin from the generator brush holder assembly.


Hide 27387B 5.INSTALL GENERATOR TERMINAL INSULATOR

a.
A307912

Install the generator terminal insulator to the generator coil assembly.

NOTICE:

Be sure to install the generator terminal insulator in the correct direction.



Hide 27039 6.INSTALL GENERATOR REAR END COVER

a.
A307911

Install the generator rear end cover to the generator coil assembly with the 3 bolts.

Torque:
4.6 N*m (47 kgf*cm, 41 in.*lbf)


Hide 27411 7.INSTALL GENERATOR PULLEY

a.

Secure the generator with regulator assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the generator pulley to the generator rotor assembly shaft by tightening the nut by hand.


c.
A310428C01
2.396,1.26 2.51,1.115 false 2.917,1.635 3.188,0.958 true 2.417,0.156 2.969,0.75 true 2.698,1.688 3.271,1.875 0.573,0.188 10 false SST1-A 1.885,0.073 2.458,0.26 0.573,0.188 10 false SST1-B 2.323,1.292 2.635,1.49 0.313,0.198 10 false *1
*1 Generator Rotor Assembly Shaft


Install SST1-A and SST1-B to the generator rotor assembly shaft as shown in the illustration.

SST
09820-63011  (09820-06010)


d.
A307907C01
2.865,0.49 1.865,0.24 true 2.938,1.375 3.115,0.708 true 2.229,1.021 2.344,0.875 false 2.094,3.167 2.406,3.365 0.313,0.198 10 false *a 1.438,2.479 1.604,2.656 0.167,0.177 10 true *b 2.146,1.031 2.458,1.229 0.313,0.198 10 false *1 2.729,1.438 3.292,1.635 0.563,0.198 10 true SST1-A 1.333,0.146 1.896,0.344 0.563,0.198 10 false SST1-B
*1 Generator Rotor Assembly Shaft
*a Hold
*b Turn


Hold SST1-A with a torque wrench, and tighten SST1-B clockwise to the specified torque.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)

NOTICE:

Check that SST is securely fitted onto the generator rotor assembly shaft.



e.
A307908E01
1.896,0.906 2.323,0.271 false 2.01,0.938 2.354,0.573 false 2.823,1.292 2.646,1.083 false 2.427,0.5 3,0.688 0.573,0.188 10 false SST1-A 2.385,0.188 2.958,0.375 0.573,0.188 10 false SST1-B 2.896,1.25 3.323,1.438 0.427,0.188 10 false SST2

Place SST2 to the nut.

SST
09820-63011  (09820-06021)


f.
A310421C01
2.594,0.552 1.646,0.24 true 2.865,1.396 2.969,0.958 true 2.688,1.458 3.24,1.635 0.552,0.177 10 false SST1-A 1.219,0.156 1.771,0.333 0.552,0.177 10 false SST2 0.938,2.875 1.25,3.073 0.313,0.198 10 false *a 2.385,2.76 2.698,2.958 0.313,0.198 10 false *b
*a Hold
*b Turn


Using an adjustable wrench, tighten the nut by turning SST1-A in the direction shown in the illustration.

Torque:
132.5 N*m (1351 kgf*cm, 98 ft.*lbf)

HINT:

Hold the adjustable wrench against the vise and tighten the nut securely.



g.

Remove SST2 from the nut.


h.
A307910C01
2.875,1.333 3.094,0.74 true 1.844,0.156 2.865,0.5 true 2.646,1.406 3.229,1.604 0.583,0.198 10 false SST1-A 1.281,0.073 1.865,0.271 0.583,0.198 10 false SST1-B 2.198,3.125 2.51,3.323 0.313,0.198 10 false *a 1.438,2.74 1.75,2.938 0.313,0.198 10 false *b
*a Hold
*b Turn


Hold SST1-A, turn SST1-B in the direction shown in the illustration, and remove SST1-A and SST1-B from the generator rotor assembly shaft.


i.

Turn the generator pulley, and check that the generator pulley moves smoothly.


j.

Remove the generator with regulator assembly from the vise.


Hide 27446A 8.INSTALL CLAMP

a.
A307906

Install the clamp to the generator coil assembly with the bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)