Home › Vehicle Interior › SEAT BELT › TONGUE PLATE STOPPER
RM30M0E _58 Vehicle Interior _017117 SEAT BELT _0092583 TONGUE PLATE STOPPER A

SEAT BELT  TONGUE PLATE STOPPER  REPLACEMENT  


PROCEDURE

Hide 73219 1.REMOVE TONGUE PLATE STOPPER

a.
B244166
1.927,0.24 2.479,0.198 true 2.333,0.531 2.677,0.76 false 1.844,1.417 2.24,1.313 true 2.729,0.719 3.021,0.99 0.292,0.271 10 false *1 2.531,0.094 2.833,0.365 0.302,0.271 10 false *a 2.281,1.188 2.573,1.49 0.292,0.302 10 false *b
*1 Tongue Plate
*a Adhesive Tape
*b Broken Tongue Plate Stopper


Slide the tongue plate above the installation position of the tongue plate stopper, and temporarily hold it with adhesive tape.


b.

Remove any pieces of the original tongue plate stopper in the belt webbing with a pair of pliers.

NOTICE:

Be careful not to damage the belt webbing during repair.



Hide 73219 2.INSTALL TONGUE PLATE STOPPER

a.
B245036
1.677,2.875 2.073,2.76 false 1.427,3.917 1.958,4.208 true 2.177,4.24 2.927,4.24 false 2.198,3.76 2.427,3.885 false 2.625,3.917 2.771,3.917 2.771,3.917 2.771,4.24 false 0.938,1.125 0.583,1.125 false 2.792,1.906 2.438,1.906 false 2.104,2.646 2.458,2.896 0.354,0.25 10 false *2 2.844,1.823 3.146,2.052 0.302,0.229 10 false *1 2.448,3.813 2.708,4.052 0.26,0.24 10 false *b 1.979,4.125 2.25,4.385 0.271,0.26 10 false *a 0.385,1.031 0.625,1.281 0.24,0.25 10 false *1 2.99,4.135 3.281,4.417 0.292,0.281 10 false *1
*1 Tongue Plate Stopper
*2 Belt Webbing
*a Male
*b Female


Position a new tongue plate stopper in the hole of the belt webbing.

HINT:

Make sure that the installation direction of the tongue plate stopper is as shown in the illustration.



b.
B244167
2.594,1.375 2.219,1.219 true 1.406,0.615 1.75,0.865 false 2.646,1.281 2.969,1.552 0.323,0.271 10 false *a 1.208,0.49 1.531,0.76 0.323,0.271 10 false *a
*a Protective Tape


Hold the tongue plate stopper in the hole of the belt webbing using an adjustable wrench, and turn the adjustment screw of the adjustable wrench by hand to compress the tongue plate stopper.

NOTICE:
·

When using the adjustable wrench, make sure to position the male and female parts of the tongue plate stopper parallel to each other.

·

Do not use pliers to compress the pin of the tongue plate stopper. They may damage the tongue plate stopper and belt webbing.



HINT:

Tape the jaws of the adjustable wrench before use.



c.
B244168
2.292,3.865 2.573,4.104 0.281,0.24 10 false *a
*a 4.5 to 5.0 mm


When the adjustment screw of the adjustable wrench cannot be turned by hand, tighten the adjustment screw using a pair of adjustable joint pliers until the tongue plate stopper thickness is 4.5 to 5.0 mm (0.177 to 0.197 in.). (Refer to the illustrations.)


d.
B245037
0.354,2.292 0.74,2.583 0.385,0.292 10 *b 0.354,0.333 0.75,0.625 0.396,0.292 10 *a
*a Correct
*b Incorrect


Make sure that the male pin of the tongue plate stopper has expanded evenly in the hole of the female part and is firmly held to the belt webbing. (Refer to the illustrations.)